Posts made by jensen3500

I tried to use the example from https://github.com/frank26080115/HephaestusConfig/blob/master/other/esp32cam_sketchbook.zip but when I compile I get an error. Has someone the same problem?

Yes, I am Running now 2.05.1.

But now i have a new stupid question. I can maximum choose 235 even though in the config 280 is set as maximum

I think its working now, i was too stupid to activate the heater 1 in the DWC

Heater is e3dv6 and connected to E0 Heater on the board and the thermistor is an genuine atc semitec 104gt connected to E0 thermistor.

M98 PCONFIG.G shows the following:

HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

Many thanks for the feedback. I think the update to version 2.0 worked. DWC shows now the hotend temperature.

But now i have a new problem, the heater is off and will not heat.

I am really sure that i have done the wiring correct.

I will try it. Just to be sure, i have only to download 2.05.1 Duet2CombinedFirmware.bin with 402KB and Upload via DWC?

I use Firmware version 1.21 and DWC 1.22.6.

I use an e3d v6 with an atc semitec 104gt.

Please find below my config.g

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Thu Jun 11 2020 22:27:38 GMT+0200 (Central European Summer Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Sparkcube Edge" ; set printer name
M667 S1 ; select CoreXY mode

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z1200.00 E370.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z600.00 E3000.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z320 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X255 Y175 Z300 S0 ; set axis maxima

; Endstops
M574 X2 Y1 Z2 S1 ; set active high endstops

; Z-Probe
M558 P0 H5 F120 T12000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X5:250 Y5:170 S20 ; define mesh grid

; Thermistors
M305 P0 T100000 B3974 R4700; Put your own H and/or L values here to set the bed thermistor ADC correction
M305 P1 T100000 B4725 C7.060000e-8 R4700; Put your own H and/or L values here to set first nozzle thermistor ADC correction

; Heaters
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
;M305 P0 T10000 B3974 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
;M305 P1 T10000 B4725 C7.060000e-8 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

Hi everybody, I bought an already used Duet Wifi and everything works fine except the thermistor of my hotend heater. The thermistor is only working if I upload the config.g file new. If I open the DWC after that again thermistor is showing n/a and I have to upload the config.g file again.

Does anyone already knew this issue? Many thanks in advance for feedback.