Posts made by jackstack

@Veti Imma have to check those out! way easier than manually measuring lol Mechanically my printers designed as a set and forget for at least several prints.

@Phaedrux Should it just be omitted then? H0 explicit but also default.

Thanks!

@Veti @Phaedrux

Yes, not using a ABL was planned. I have some adjustment for the Z end stop so I can decrease that ~3mm offset and do a more consistent job of generating the mesh bed. The scale of the display does make it seem horrible but I'm using a large nozzle so theres margin here compared to a .4mm nozzle.homeall.g

In terms of Y stepper, i was actually having worse performance running a lower acceleration for Y, speed is reasonable due to diminished torque at higher RPM but the G0 also failed at F1200 mm/minbed.g

As for "probe" I don't have one. I have a Z end stop that sets min axis point. M558 P0 H5 F120 T1200 "P0" sets it to no probe and it prompts you to manually job the z down to touch the bed.

@Phaedrux Huh, I thought Duet 2 wifi was listed as 3A max for stepper. Is it current limiting to 2400 or do I need to set it to 2400. Based on the stepper motor sizing forum page, the only "not ideal" setting of the nema 23 I'm using is its 5.4 mH.

@Veti

Important to preface that the bed is massive, unheated and fixed, and I'm not using ABL sensor. It's manually generated mesh map with a Z end stop below the bed about 3mm. I couldn't find any recommendation for resetting Z0 datum manually, but single axis moves have been fine with G29 S1 eg. moving from X min to x max Z has responded and maintained consistent height above bed and in the slicer it compensates down to initial layer reference to the mesh bed.

config.g

Not sure if M122 has to be after i replicate the failure.

Thanks!

11:44:32 PMM122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F2MS4-7JTDL-3SJ6S-TWUNH
Used output buffers: 3 of 24 (7 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93076 of which 0 recycled
Exception stack ram used: 440
Never used ram: 11844
Tasks: NETWORK(ready,764) HEAT(blocked,872) MAIN(running,3736) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:36:28 ago, cause: software
Last software reset at 2021-01-28 23:08, reason: User, spinning module GCodes, available RAM 11836 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 27.1, current 27.3, max 28.9
Supply voltage: min 22.3, current 24.1, max 25.8, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/280
Driver 1: standstill, SG min/max 0/1023
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-01-28 23:44:30
Cache data hit count 4294967295
Slowest loop: 15.78ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 154, MaxWait: 72615ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 36, completed moves: 36, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.48ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 60:01:94:2e:d0:ab
  WiFi Vcc 3.37, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 22896
  WiFi IP address 192.168.1.115
  WiFi signal strength -56dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0

So I need to bump up my Z speed so it works together? Bit confusing as the G0 X450 Y850 Z0.5 F1800 is called when position is X200 Y40 and Z15. So it would seam like Z has plenty of time to complete the moves, and my mesh bed points are spaced 200 mm apart. If Z were to lag due to stiction or something, would that impact the other axis from completing its move? Thank you for the help!

So I have a custom built gantry on a fixed bed-style printer. I have my axis tuned with nema 17 on everything except the y (which moves the gantry). This uses a nema 23 driving a hub on a fixed leadscrew. Great torque and power, I can accelerate at 700mm/s^2 to 30 mm/s and change direction instantly all day moving a ~50lb gantry.

Here's the issue: when the mesh bed leveling height map is loaded (G29 S1), and I do a G0 rapid move controlling X Y and Z, the y axis stepper seizes and emits a high whine after its accelerated to 30mm/s and moved for ~200mm.

I have repeated the Identical G0 rapid move without the mesh bed level active (G29 S2 in command console before G0 move) and it works flawlessly.

This issue is unfortunately critical is its the move generated by Cura in between start Gcode and print code

Other supporting info for my Y axis:
Nema 23 269 oz-in 2.8 amp
2272 steps per mm
x16 interpolation (tried x1 but too rough for smaller moves)
420 mm/min jerk
600 mm/s^2 accel
1800 mm/s max speed

Is it possible I'm hitting a saturation point of either current or processing power because of all 4 motors moving simultaneously? (double motor for Z axis, 2 screws)
I was trying to view the code behind a G29 S1 but couldn't figure out how to see it.
Thanks in advance!