Best posts made by InsanityAutomation

undefined

@oliof It's worth noting if I load 3.0.0 back to it, everything works smoothly again. No physical change between when it works and then doesn't on 3.1.1.

undefined

Heres a few photos : https://photos.app.goo.gl/N7Ea1rB1NPq9jCTEA

undefined

M569 P2
Drive 2 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 127

undefined

Seems akismet wants to flag it as spam for some reason... lol Im adding a bit more content above it to try and get rid of that warning....

M569 P0
Drive 0 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0

M569 P1
Drive 1 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0

M569 P2
Drive 2 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63

M569 P3
Drive 3 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0

M569 P4
Drive 4 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63

M569 P5
Drive 5 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0

M569 P6
Drive 6 runs in reverse, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0

M569 P7
Drive 7 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0

M569 P8
Drive 8 runs in reverse, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0

M569 P9
Drive 9 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63

undefined

Im trying to get the Formbot Troodon updated to 3.1.1 and running into an odd issue. Firstoff, this is a custom compatible board. Its essentially a Duet2Wifi and Duex5 in a single PCB with bigfoot format 2660 removable drivers.

The machine works as intended on 3.0.0. Config is here :
https://github.com/InsanityAutomation/FormbotTroodon/blob/master/sys/config.g

3.0.1 RC11 and 3.1.1 Release both exhibit the same issue. Any motion command to any stepper gets the following response :

M997 S1
Warning: motor phase A may be disconnected reported by driver(s) 0 1
Warning: motor phase B may be disconnected reported by driver(s) 0 1

I tried changing to a new stepper motor to be sure with no dice. Rolling back to 3.0.0 everything works as intended.

I attempted to modify the current values from 1200 down to 1000 and up to 1300 with no change.

Anyone have any ideas of something to try? Is there some other change between these versions im missing from the release notes?

Thanks

undefined

Thats correct, no changes other than bringing the firmware bin file back and forth.

With 3.0.0 Installed :
M98 Pconfig.g

Error: M574: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead.
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: M307: Heater 3 not found
Warning: M307: heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 542C.

Error: M106: Fan number 3 not found
Error: M106: Fan number 4 not found
Error: M106: Fan number 5 not found
Error: M106: Fan number 6 not found
Error: M106: Fan number 7 not found
Error: M106: Fan number 8 not found

M122

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DJM-9178L-L4MSJ-6J9FG-3S86S-982QP
Used output buffers: 3 of 24 (10 max)
=== RTOS ===
Static ram: 30516
Dynamic ram: 92392 of which 60 recycled
Exception stack ram used: 504
Never used ram: 7600
Tasks: NETWORK(ready,640) HEAT(blocked,1240) DUEX(suspended,160) MAIN(running,3676) IDLE(ready,156)
Owned mutexes:
=== Platform ===
Last reset 45:02:35 ago, cause: software
Last software reset at 2020-05-04 22:19, reason: User, spinning module GCodes, available RAM 7356 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 24.5, current 26.7, max 27.8
Supply voltage: min 23.8, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/223
Driver 1: standstill, SG min/max not available
Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available
Driver 5: standstill, SG min/max 0/244
Driver 6: standstill, SG min/max 0/242
Driver 7: standstill, SG min/max 0/234
Driver 8: standstill, SG min/max 0/241
Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available
Date/time: 2020-06-16 09:59:35
Cache data hit count 4294967295
Slowest loop: 77.99ms; fastest: 0.09ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 167, MaxWait: 27507ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 11, completed moves: 11, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.49ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 2c:f4:32:58:8a:07
WiFi Vcc 3.38, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 23992
WiFi IP address 172.16.0.213
WiFi signal strength -58dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: no filament

And with 3.1.1

M98 Pconfig.g
Error: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead.
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Heater 3 not found
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 542C
Error: Fan number 3 not found
Error: Fan number 4 not found
Error: Fan number 5 not found
Error: Fan number 6 not found
Error: Fan number 7 not found
Error: Fan number 8 not found

M122

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DJM-9178L-L4MSJ-6J9FG-3S86S-982QP
Used output buffers: 3 of 24 (12 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 94372 of which 100 recycled
Exception stack ram used: 264
Never used ram: 8356
Tasks: NETWORK(ready,392) HEAT(blocked,1224) DUEX(suspended,160) MAIN(running,1552) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:57 ago, cause: software
Last software reset at 2020-05-04 22:19, reason: User, spinning module GCodes, available RAM 7356 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 25.9, current 26.6, max 26.9
Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available
Date/time: 2020-06-16 10:02:11
Cache data hit count 57130340
Slowest loop: 78.89ms; fastest: 0.62ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 20.11ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 2c:f4:32:58:8a:07
WiFi Vcc 3.38, reset reason Unknown
WiFi flash size 4194304, free heap 24160
WiFi IP address 172.16.0.213
WiFi signal strength -54dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: no filament
=== DueX ===
Read count 1, 1.04 reads/min

undefined

Also worth noting the 3 drivers listing error states (2,4, and 9) do not physically exist on this board.

Thanks

undefined

Those do function to stop the flood of warnings that were present before adding them. The command goes green in the terminal after sending on DWC with no error reported. No change in M122 output.

If my memory is correct, the M574 command was included in the 3.0 documentation on setting up the BLTouch to release the z endstop pin. Is there another line required to do the same thing with 3.1.1 or is it unassigned by default?