@oliof It's worth noting if I load 3.0.0 back to it, everything works smoothly again. No physical change between when it works and then doesn't on 3.1.1.
InsanityAutomation
@InsanityAutomation
Best posts made by InsanityAutomation
-
RE: Formbot Troodon RRF 3.1.1 Update
-
RE: Formbot Troodon RRF 3.1.1 Update
M569 P2
Drive 2 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 127 -
RE: Formbot Troodon RRF 3.1.1 Update
Seems akismet wants to flag it as spam for some reason... lol Im adding a bit more content above it to try and get rid of that warning....
M569 P0 Drive 0 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P1 Drive 1 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P2 Drive 2 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63 M569 P3 Drive 3 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P4 Drive 4 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63 M569 P5 Drive 5 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P6 Drive 6 runs in reverse, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P7 Drive 7 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P8 Drive 8 runs in reverse, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P9 Drive 9 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63
-
Formbot Troodon RRF 3.1.1 Update
Im trying to get the Formbot Troodon updated to 3.1.1 and running into an odd issue. Firstoff, this is a custom compatible board. Its essentially a Duet2Wifi and Duex5 in a single PCB with bigfoot format 2660 removable drivers.
The machine works as intended on 3.0.0. Config is here :
https://github.com/InsanityAutomation/FormbotTroodon/blob/master/sys/config.g3.0.1 RC11 and 3.1.1 Release both exhibit the same issue. Any motion command to any stepper gets the following response :
M997 S1
Warning: motor phase A may be disconnected reported by driver(s) 0 1
Warning: motor phase B may be disconnected reported by driver(s) 0 1I tried changing to a new stepper motor to be sure with no dice. Rolling back to 3.0.0 everything works as intended.
I attempted to modify the current values from 1200 down to 1000 and up to 1300 with no change.
Anyone have any ideas of something to try? Is there some other change between these versions im missing from the release notes?
Thanks
-
RE: Formbot Troodon RRF 3.1.1 Update
Thats correct, no changes other than bringing the firmware bin file back and forth.
With 3.0.0 Installed :
M98 Pconfig.gError: M574: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead. HTTP is enabled on port 80 FTP is disabled TELNET is disabled Error: M307: Heater 3 not found Warning: M307: heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 542C. Error: M106: Fan number 3 not found Error: M106: Fan number 4 not found Error: M106: Fan number 5 not found Error: M106: Fan number 6 not found Error: M106: Fan number 7 not found Error: M106: Fan number 8 not found
M122
=== Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later + DueX5 Board ID: 08DJM-9178L-L4MSJ-6J9FG-3S86S-982QP Used output buffers: 3 of 24 (10 max) === RTOS === Static ram: 30516 Dynamic ram: 92392 of which 60 recycled Exception stack ram used: 504 Never used ram: 7600 Tasks: NETWORK(ready,640) HEAT(blocked,1240) DUEX(suspended,160) MAIN(running,3676) IDLE(ready,156) Owned mutexes: === Platform === Last reset 45:02:35 ago, cause: software Last software reset at 2020-05-04 22:19, reason: User, spinning module GCodes, available RAM 7356 bytes (slot 1) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 0.0ms, max retries 0 MCU temperature: min 24.5, current 26.7, max 27.8 Supply voltage: min 23.8, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max 0/223 Driver 1: standstill, SG min/max not available Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 5: standstill, SG min/max 0/244 Driver 6: standstill, SG min/max 0/242 Driver 7: standstill, SG min/max 0/234 Driver 8: standstill, SG min/max 0/241 Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available Date/time: 2020-06-16 09:59:35 Cache data hit count 4294967295 Slowest loop: 77.99ms; fastest: 0.09ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 167, MaxWait: 27507ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves: 11, completed moves: 11, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Stack records: 2 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 15.49ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 2c:f4:32:58:8a:07 WiFi Vcc 3.38, reset reason Turned on by main processor WiFi flash size 4194304, free heap 23992 WiFi IP address 172.16.0.213 WiFi signal strength -58dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: no filament
And with 3.1.1
M98 Pconfig.g Error: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead. HTTP is enabled on port 80 FTP is disabled TELNET is disabled Error: Heater 3 not found Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 542C Error: Fan number 3 not found Error: Fan number 4 not found Error: Fan number 5 not found Error: Fan number 6 not found Error: Fan number 7 not found Error: Fan number 8 not found
M122
=== Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later + DueX5 Board ID: 08DJM-9178L-L4MSJ-6J9FG-3S86S-982QP Used output buffers: 3 of 24 (12 max) === RTOS === Static ram: 27980 Dynamic ram: 94372 of which 100 recycled Exception stack ram used: 264 Never used ram: 8356 Tasks: NETWORK(ready,392) HEAT(blocked,1224) DUEX(suspended,160) MAIN(running,1552) IDLE(ready,80) Owned mutexes: WiFi(NETWORK) === Platform === Last reset 00:00:57 ago, cause: software Last software reset at 2020-05-04 22:19, reason: User, spinning module GCodes, available RAM 7356 bytes (slot 1) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN Error status: 0 MCU temperature: min 25.9, current 26.6, max 26.9 Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 5: standstill, SG min/max not available Driver 6: standstill, SG min/max not available Driver 7: standstill, SG min/max not available Driver 8: standstill, SG min/max not available Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available Date/time: 2020-06-16 10:02:11 Cache data hit count 57130340 Slowest loop: 78.89ms; fastest: 0.62ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 3.0ms, write time 0.0ms, max retries 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 20.11ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 2c:f4:32:58:8a:07 WiFi Vcc 3.38, reset reason Unknown WiFi flash size 4194304, free heap 24160 WiFi IP address 172.16.0.213 WiFi signal strength -54dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: no filament === DueX === Read count 1, 1.04 reads/min
-
RE: Formbot Troodon RRF 3.1.1 Update
Also worth noting the 3 drivers listing error states (2,4, and 9) do not physically exist on this board.
Thanks
-
RE: Formbot Troodon RRF 3.1.1 Update
Those do function to stop the flood of warnings that were present before adding them. The command goes green in the terminal after sending on DWC with no error reported. No change in M122 output.
If my memory is correct, the M574 command was included in the 3.0 documentation on setting up the BLTouch to release the z endstop pin. Is there another line required to do the same thing with 3.1.1 or is it unassigned by default?
Latest posts made by InsanityAutomation
-
RE: Formbot Troodon RRF 3.1.1 Update
Figured I'd bump this and see if anyone had any other idea before i dig into source myself.
-
RE: Formbot Troodon RRF 3.1.1 Update
I can grab some photos of it when I get home (Remote VPN for last testing bits!) Personally I really like the removable drivers despite the thermal constraints as they are still one of the most failure prone components on these boards. People who (ab)use machines like I do tend to go through a few of em....
-
RE: Formbot Troodon RRF 3.1.1 Update
Id assume so as well. When I showed Tony the board at ERRF last year he was glad to see something not a direct clone for a change but here is the risk of it not being a direct clone lol
-
RE: Formbot Troodon RRF 3.1.1 Update
@Phaedrux said in Formbot Troodon RRF 3.1.1 Update:
M569 P4 R-1
Yup, no change in function or output sending those manually.
-
RE: Formbot Troodon RRF 3.1.1 Update
Seems akismet wants to flag it as spam for some reason... lol Im adding a bit more content above it to try and get rid of that warning....
M569 P0 Drive 0 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P1 Drive 1 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P2 Drive 2 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63 M569 P3 Drive 3 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P4 Drive 4 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63 M569 P5 Drive 5 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P6 Drive 6 runs in reverse, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P7 Drive 7 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P8 Drive 8 runs in reverse, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 0 M569 P9 Drive 9 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 63
-
RE: Formbot Troodon RRF 3.1.1 Update
M569 P2
Drive 2 runs forwards, active low enable, step timing fast, mode spreadCycle, ccr 0x101b4, toff 4, tblank 2, hstart/hend/hdec 3/3/0, pos 127 -
RE: Formbot Troodon RRF 3.1.1 Update
Those do function to stop the flood of warnings that were present before adding them. The command goes green in the terminal after sending on DWC with no error reported. No change in M122 output.
If my memory is correct, the M574 command was included in the 3.0 documentation on setting up the BLTouch to release the z endstop pin. Is there another line required to do the same thing with 3.1.1 or is it unassigned by default?
-
RE: Formbot Troodon RRF 3.1.1 Update
Also worth noting the 3 drivers listing error states (2,4, and 9) do not physically exist on this board.
Thanks
-
RE: Formbot Troodon RRF 3.1.1 Update
Thats correct, no changes other than bringing the firmware bin file back and forth.
With 3.0.0 Installed :
M98 Pconfig.gError: M574: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead. HTTP is enabled on port 80 FTP is disabled TELNET is disabled Error: M307: Heater 3 not found Warning: M307: heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 542C. Error: M106: Fan number 3 not found Error: M106: Fan number 4 not found Error: M106: Fan number 5 not found Error: M106: Fan number 6 not found Error: M106: Fan number 7 not found Error: M106: Fan number 8 not found
M122
=== Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later + DueX5 Board ID: 08DJM-9178L-L4MSJ-6J9FG-3S86S-982QP Used output buffers: 3 of 24 (10 max) === RTOS === Static ram: 30516 Dynamic ram: 92392 of which 60 recycled Exception stack ram used: 504 Never used ram: 7600 Tasks: NETWORK(ready,640) HEAT(blocked,1240) DUEX(suspended,160) MAIN(running,3676) IDLE(ready,156) Owned mutexes: === Platform === Last reset 45:02:35 ago, cause: software Last software reset at 2020-05-04 22:19, reason: User, spinning module GCodes, available RAM 7356 bytes (slot 1) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 0.0ms, max retries 0 MCU temperature: min 24.5, current 26.7, max 27.8 Supply voltage: min 23.8, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max 0/223 Driver 1: standstill, SG min/max not available Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 5: standstill, SG min/max 0/244 Driver 6: standstill, SG min/max 0/242 Driver 7: standstill, SG min/max 0/234 Driver 8: standstill, SG min/max 0/241 Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available Date/time: 2020-06-16 09:59:35 Cache data hit count 4294967295 Slowest loop: 77.99ms; fastest: 0.09ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 167, MaxWait: 27507ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves: 11, completed moves: 11, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Stack records: 2 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 15.49ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 2c:f4:32:58:8a:07 WiFi Vcc 3.38, reset reason Turned on by main processor WiFi flash size 4194304, free heap 23992 WiFi IP address 172.16.0.213 WiFi signal strength -58dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: no filament
And with 3.1.1
M98 Pconfig.g Error: endstop type 0 is no longer supported. Use type 1 and invert the input pin instead. HTTP is enabled on port 80 FTP is disabled TELNET is disabled Error: Heater 3 not found Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 542C Error: Fan number 3 not found Error: Fan number 4 not found Error: Fan number 5 not found Error: Fan number 6 not found Error: Fan number 7 not found Error: Fan number 8 not found
M122
=== Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later + DueX5 Board ID: 08DJM-9178L-L4MSJ-6J9FG-3S86S-982QP Used output buffers: 3 of 24 (12 max) === RTOS === Static ram: 27980 Dynamic ram: 94372 of which 100 recycled Exception stack ram used: 264 Never used ram: 8356 Tasks: NETWORK(ready,392) HEAT(blocked,1224) DUEX(suspended,160) MAIN(running,1552) IDLE(ready,80) Owned mutexes: WiFi(NETWORK) === Platform === Last reset 00:00:57 ago, cause: software Last software reset at 2020-05-04 22:19, reason: User, spinning module GCodes, available RAM 7356 bytes (slot 1) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN Error status: 0 MCU temperature: min 25.9, current 26.6, max 26.9 Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: temperature-shutdown! short-to-ground standstill, SG min/max not available Driver 5: standstill, SG min/max not available Driver 6: standstill, SG min/max not available Driver 7: standstill, SG min/max not available Driver 8: standstill, SG min/max not available Driver 9: temperature-shutdown! short-to-ground standstill, SG min/max not available Date/time: 2020-06-16 10:02:11 Cache data hit count 57130340 Slowest loop: 78.89ms; fastest: 0.62ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 3.0ms, write time 0.0ms, max retries 0 === Move === Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms Bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === AuxDDARing === Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 20.11ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 2c:f4:32:58:8a:07 WiFi Vcc 3.38, reset reason Unknown WiFi flash size 4194304, free heap 24160 WiFi IP address 172.16.0.213 WiFi signal strength -54dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: no filament === DueX === Read count 1, 1.04 reads/min