Topics created by gringo

Thanks @droftarts so i will use manuel Bed Levelling Assistant.

Checked it today.
OrcaSlicer 1.9.0 edited some Rows in the G-Code, after I commented it out it works.
GCode Orca1.9.0.JPG

Thank you for the execution,

I have two other printers with Duet Boards where I print slower and with much less acceleration.

I have not tested Klipper yet, but I am planning to build the next printer and run it with Klipper to have a comparison.

I printed the VZ Cupe at 100mm/s with 5K ACC of the outer perimeter.
Reducing the acceleration of the outer perimeter to 2K at 100mm/s has brought significant improvement.

In my opinion, I should also be able to select the speed and acceleration in the selection window for Input Shaper as the frequencies change at different speeds and accelerations.

Thanks for the correction, I had mistyped.
In the post above it should read 30 and not 20 degrees.

I have 30 degrees difference with the Extrudr GreenTEC Pro.
50 degrees and more with the CR3D ABS FibCR20.

That was misleadingly expressed by me

I tested 2 PT1000. With both the same.

I think I will buy a 2K Ohms and a 1K ohms resistor for testing.

@gringo glad to help you

Thanks oliof,
For example, if I take GND from out6, how to configure the M950 command?
M950 E0 C"out6"

Is that correct?

It works. Thanks a lot

@gringo

thats it. Now it works.

Thanks a lot @droftarts

@gringo
Ok
I'm clearly not up with M150 so hopefully someone else can help

All I can suggest is changing this

;loop through all the LED's while iterations < global.ledSize - 1 ; set to 1 less than number of LED's in neopixel if global.runLED = false M150 R0 U0 B0 P0 W0 S58 F0 ; turn off neopixels echo "exiting loop" break if global.ledState = 0 echo "next LED on " , iterations M150 R{global.rLED} U{global.gLED} B{global.bLED} W{global.wLED} P{global.ledBrightness} S1 F0 else echo "Next LED off" , iterations M150 R0 U0 B0 W0 P0 S1 F0 ; set next LED in loop to either brightness or off G4 S{global.ledDelay}

To this

;loop through all the LED's while iterations < global.ledSize if global.runLED = false M150 R0 U0 B0 P0 W0 S58 F0 ; turn off neopixels echo "exiting loop" break if global.ledState = 0 echo "next LED on " , iterations M150 R{global.rLED} U{global.gLED} B{global.bLED} W{global.wLED} P{global.ledBrightness} S{iterations+1} F0 else echo "Next LED off" , iterations M150 R0 U0 B0 W0 P0 S{iterations +1} F0 ; set next LED in loop to either brightness or off G4 S{global.ledDelay}

@dc42

Yes,I’m using E3D Stepper

@dc42 maybe re-using the 3d scanner interface, or an SBC extension talking klipper MCU protocol to the beacon probe would be an option.

There are enough connections, I'm just thinking how to configure it.
The slider and the winder should run until I stop.
The slider should drive into the left end stop, then reverse and drive into the right end stop and back again.
I have thought about realizing this via a macro.

@achrn

it works, thanks a lot.

Thanks for your help, the Board is running again. I first tried to flash the complete .zip file via BOSSA. Of course it does not work . After flashing the .bin I had to install the USB drivers.
After that I had no access with YAT. Pronterface then worked and I could set up the Network.

Thanks to all.

Thanks. Works now

This is my Start Gcode in S3D
G28 ;
G1 Z3 F500 ;

M140 S[bed0_temperature] ; set bed temp
M109 S[extruder1_temperature] T2 ;heat right tool before moving
M109 S[extruder0_temperature] T2 ;heat left tool before moving

T2 ; Copy Mode

M117 Start Printing...

T2 will be selected and the emp

T2 is selected and the temperatures are set.
Shortly before the printout starts, Tool 1 is selected and only one object is printed.
What do I still have to set there?

Found my Mistake.Unbenannt.JPG

All the time was selected in S3D Tool 0, see the yellow marker.
Who could have known that Tool 2 must be selected there?

Now it works.

I have now set a fan speed for Layers 1, 2 and 3 of 1%, 50% and 100% in S3D.
I let Tool 1 heat up first, so it works now.

Now it works, i have performed the steps again.

Thanks for your help

Thanks a lot.

I have modified your bed.g and now it works.