Posts made by Gear

thanks @deckingman I'll give it a try once I have the fan actually wired into the bed, but this should probably work well.

So my printer is enclosed and has an enclosure fan but not an enclosure heater because it already reaches 50 degrees easily.

Now I am wanting to use a fan to turn on once the camber reaches 45 degrees because that's the temperature i'm most comfortable with.

I'm using RRF3 on a duet2 wifi

@dc42 @deckingman i'm running an 0.4 nozzle, I tried deckingman his method with petg and this is the result I got on

M572 D0 S0.2

S 0.2

@dc42 picture model as you can see all the corners are sharp as a knife.

yes I used that, but couldn't really see a difference.

M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E415.00 ; Set steps per mm
M566 X600.00 Y600.00 Z12.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X7500.00 Y7500.00 Z300.00 E3600.00 ; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z20.00 E3000.00 ; Set accelerations (mm/s^2)
M906 X1600.00 Y1600.00 Z1200.00 E300.00 I30 ; Set motor currents (mA) and motor idle factor in per cent

might have to do solid infill and see how it fares.

Hello! I've been trying to tune pressure advance (pa) for a bit now and basically did M572 D0 S0.05 every 20 layers (with the little gcode bar at the top) and see if there is any difference. though the problem is is that I don't see any differences between the 10 settings from S0.05-> 0.2
I'm printing this model at 100mm/s with a 60cm capricorn xs bowden driven by a bondtech bmg and a genuine e3d v6.

I made a little test model
angle one

angle two

angle three

enable retract on layer change.

@deckingman @burtoogle which such high jerk values don't you find your extruder to make a louder sound, this might have put my off at first.

@syko_symatic just press f5 untill it loads ...

I'm having serious issues tuning my bowden setup, some people pointed out that my acceleration and jerk settings where a bit high. could you guys help me out? ps: I use a 600mm bowden

M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E415.00 ; Set steps per mm
M566 X600.00 Y600.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X7500.00 Y7500.00 Z300.00 E3600.00 ; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z20.00 E150.00 ; Set accelerations (mm/s^2)
M906 X1600.00 Y1600.00 Z1200.00 E300.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30

no not yet haven't found a way to calibrate it yet for my printer any idea
how @bot ?

like it's not preducing any blobs or stings on this setting it's only acting up after a travel

Gear 9 Feb 2019, 14:54

Hello everyone,

first of all I'm in love with my duet2wifi damn what a joy to just be able to toss gcodes to your browser and having it print.

so I have finished my hypercube evo for 2 weeks now and all in all I love the design and all the bells and whistles I added to it. though this is the first time using a bowden and I just can't figure out why it's underextruding after a long travel move, I searched everywhere online and couldn't seem to solve it. please be my hero and safe me.

I tried dissabling coasting this didn't fix it. for the top layer for the bridging test it seems to travel from the other side and start extruding the last inner wall before starting with the roof, but it needs the whole inner wall section to prime the nozzle.

https://imgur.com/a/N2jzdjT

I think all the info is in the imgur pictures, if you need anything else I can deliver.

edit : i'm running firmware 2.01(RTOS)

0_1549807109838_bridging test gcode with failing toplayers.gcode

the weird part is that it only happens when it travels a long while and than has to extrude, if you look at my calibration cubes the top layer is mostly perfect. I just can't seem to figure out what the issue is. temp is fine and filament diameter is 1.78

i'm still at a loss

this seems more like issue you have to resolve because if your probe is malfunctioning it's better to just ditch it and get something else to probe.

left is with max comb distance of 10 (top surface on the bridges look a lot better)
right is with combing turned off.

sadly enough this doesn't seem to fix it :<

0_1549732657477_bridging test gcode with failing toplayers.gcode

here is the gcode for the bridging test where the top layer failed. also looking at the path it takes and the model on my desk it's only showing serious issues after long travel moves. so on one side the middle part is fine but the second layer is not because it's "priming" and on the other side the inner wall is missing because it's using that as "prime" or something.

Hello everyone,

first of all I'm in love with my duet2wifi damn what a joy to just be able to toss gcodes to your browser and having it print.

so I have finished my hypercube evo for 2 weeks now and all in all I love the design and all the bells and whistles I added to it. though this is the first time using a bowden and I just can't figure out why it's underextruding after a retraction, I searched everywhere online and couldn't seem to solve it. please be my hero and safe me.

https://imgur.com/a/N2jzdjT

I think all the info is in the imgur pictures, if you need anything else I can deliver.

edit : i'm running firmware 2.01(RTOS)