Posts made by GBusy24

GBusy24
20 Apr 2025, 13:54

I recently replaced a Duet 2 Wifi board with the same. I'm now connected to it and after establishing wifi connection with the card that came with the board, I powered down and reinstalled the SD card from the original board. Motors move in correct direction and it homes correctly also, but when attempting to probe the bed or extrude filament, I get unexpected movements from the carriage. For one example, when I send command G1 E100 F60, instead of extruding filament, the print head/carriage takes off to the right rear of the machine W/O attempting to extrude any filament. I'm a bit confused and wonder if anyone can offer me some insights. Thanks

@droftarts @Phaedrux , I think it was both the error with the quotatiion mark and also the I parameter I had in the 587. I'm jusy happy you guys help me solve it. Thanks again.

@droftarts I finally solved it. I'm connected and I just pulled up DWC. Thanks

@droftarts The only time I've been able to get the wifi module green to turn on is when I set up the access point mode

@droftarts Finally thought to do this that you told me to do a couple of days ago, so I thought I'd let you see it too.Network Scan.txt

@droftarts Greg''s WIFI was listed, but W/O the apostrophe and I went ahead and ran the commands you said anyway just in case, You can see the 'No network found' result, so I sent the second group of commands you mentioned and my wifi light on the board goes off and I can't connect in normal mode. Head scratching time. Please advise.Terminal Snippet.txt

@droftarts Thanks, I'll do this when I get home from work.

@droftarts M587 S"Greg''s WIFI" P"**********" I192.168.0.62

@droftarts I sent a 587 command after that.

@droftarts Setup as access point.Terminal Snippet.txt

@Phaedrux, @droftarts, @jay_s_uk,

I've got the solid green light for the wifi module showing and at this point I assumed I could pull up DWC Thru my browser and my static IP, but that's not working for me. So I disconnect USB power and turn main power on and still, no luck. Please advise.

@Phaedrux, @droftarts, @jay_s_uk, Thanks for everyone's help. I'm connected!

@Phaedrux, @droftarts,
I've got Access Point setup with the special characters corrected and it's giving me my access point. At this stage, shouldn't I be able to just type that IP into my browser. I'm still missing something. Right? Thanks

@droftarts Aha! Good to know. Thanks,

@Phaedrux The answer is yes to all 3 of your questions. It's morning here and I'll try that when I get home from work.

@jay_s_uk I set my network ...........it remembers it and M587 confirms. I send M552 S1 and get 'No known networks found".

M587 S"Greg's WIFI" P"**********"
M587
Remembered networks:
Gregs WIFI IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
TNCAPF318D9 IP=192.168.1.14 GW=0.0.0.0 NM=0.0.0.0
ok
M552 S1
ok
Error: WiFi module reported: no known networks found

@jay_s_uk I've now switched out the antennas, but still in same condition. No connection. Scratching my head. Here's a pic of the board. Is it a mistake to wire everything up before connecting? I know I've done this before successfully.20250415_191452.jpg

@jay_s_uk okay thanks

@jay_s_uk I will say that when working with the other board the green light on the Wi-Fi module would blink constantly where I get nothing out of this current board I'm working with