Posts made by Gasstaldy

@phaedrux Thanks, the Z axes turned out well.
Now I have the problem that the extruder does not appear in DWG or in the Duet panel

; Drives
M569 P0.0 S1                                       ; physical drive 0.0 goes forwards	//X
M569 P0.1 S1                                       ; physical drive 0.1 goes forwards	//Y
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards	//Z
M569 P0.3 S0                                       ; physical drive 0.3 goes forwards	//Z
M569 P0.4 S1                                       ; physical drive 0.4 goes forwards	//E
M584 X0.0 Y0.1 Z0.2:0.3 E0.4                       ; set drive mapping
M350 X32 Y32 Z16 E16 I1                         ; configure microstepping with interpolation
M92 X160.21 Y160.28 Z400.00 E420.00        ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00        ; set maximum instantaneous speed changes (mm/min)	//cambios instantaneos de direccion (jerk)
M203 X21000.00 Y21000.00 Z500 E3000.00  ; set maximum speeds (mm/min)	//Maximas velocidades que puede alvanzar los ejes
M201 X6000 Y6000 Z20 E250.00         ; set accelerations (mm/s^2)	//la forma en la que acelera por segundo los ejes
M906 X800 Y800 Z1100 E800 I30                  ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X600 Y570 Z498.75 S0                           ; set axis maxima

; Endstops
M574 X1 S1 P"!io1.in"                              ; configure switch-type (e.g. microswitch) endstop for low end on X via pin !io1.in
M574 Y1 S1 P"!^io2.in"                             ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin !^io2.in
M574 Z2 S1 P"!^io3.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on Z via pin !^io3.in

; Z-Probe
M950 S0 C"io4.out"                                 ; create servo pin 0 for BLTouch
M558 P9 C"io4.in" H5 F6000 T6000 P5               ; set Z probe type to bltouch and the dive height + speeds //H altura a la que se despliega la sonda
G31 P500 X45 Y0 Z-0.71                             ; set Z probe trigger value, offset and trigger height	//-3.04
M557 X0:600 Y0:570 S150                            ; define mesh grid


; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 ;U"TMK8"       ; configure sensor 0 as thermistor on pin temp0 //U nombre del sensor
M950 H0 C"out1" T0                                 ; create nozzle heater output on out1 and map it to sensor 0 //H numero de hotend -
M307 H0 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H0 S280                                       ; set temperature limit for heater 0 to 280C

; Fans
M950 F0 C"out8" Q500                               ; create fan 0 on pin out8 and set its frequency
M106 P0 C"FanExtrusor" S0 H0 T100                  ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"out7" Q500                               ; create fan 1 on pin out7 and set its frequency
M106 P1 C"FanCapa" S1 H-1                          ; set fan 1 name and value. Thermostatic control is turned off

; Tools
M563 P1 S"MK8" D1 H0 F0:1                          ; define tool 1
G10 P1 X0 Y0 Z0                                    ; set tool 1 axis offsets
G10 P1 R0 S0                                       ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T1                                                 ; select first tool

@phaedrux thank you, I see that it is quite simple, I just couldn't find where to start

How to configure two drivers for the Z axis?
I have one motor connected to driver 2. And the other to driver 3

@dc42 Thanks to your technical clarification, I was able to understand more about the problem, and connected the DUET with another cable to port C of my PC, and problem solved. already loaded with BOSSA. And my DUET is working perfectly.

Thanks to everyone who contributed and helped me.

@phaedrux A few months ago on Amazon, I bought it and now I want to use it

@phaedrux

@phaedrux I don't have raspberry pi

I have a duet 3 6HC board. It is new, and when I connect it to the PC, it marks the port as; "device description request error"
DIAG led stays on dim all the time

I have the indicated drivers installed on the PC, I have already followed many procedures, including erasing the memory by bypassing the erase pins.

I already tried with many USB cables, I already used all the ports of the PC. even another PC. and nothing.

I don't know what to do I need help.

https://docs.duet3d.com/en/User_manual/Troubleshooting/Duet_wont_respond

@dc42 I have the same problem with the duet 3HC6. And when connecting it to the pc it does not recognize the duet (I already installed drivers) and I followed the procedure that it mentions @Phaedrux