Posts made by Empiricus

@jay_s_uk Yes that is during print. No data received.

@fcwilt Thanks all installed

@diy-o-sphere Thanks all installed succesfully. Now I am trying to get the magnetic filament sensor to work. After updating to 2.05.1 I just get:
Duet3D magnetic filament monitor on input 3, enabled, sensitivity 24.80mm/rev, allow 70% to 130%, check every 10.0mm, no data received.
Cables are fine all is rotating when filament is pulled but no data? Only one green flash after switch on. Any suggestions?

I am trying to get the magnetic filament sensor to work. After updating to 2.05.1 I just get:
Duet3D magnetic filament monitor on input 3, enabled, sensitivity 24.80mm/rev, allow 70% to 130%, check every 10.0mm, no data received.
Cables are fine all is rotating when filament is pulled but no data? Only one green flash after switch on. Any suggestions?

Server is running but only white window when I connect to IP. Duet webControl 2.07 zip only has .gz files and folders. How do I install these on Duet2 ?

@fcwilt Thanks, I installed 2.05 and Duet wifi server but there is nothing on how to install Duet webControl. Zip contains folders and .gz files. server is starting but nothing shows up when connecting to the IP ( blank white window).

I need to install Version 2.05.1
DuetWiFiServer 1.23
DuetWebControl 2.0.7 or 1.22.6

Where do I find the files? I see Changelogs etc but no files to install.

No I cannot update to 3 already f'ed up all trying that.

Updated with DuetWiFiServer. Panel shows the web server started and IP but blank screen in DWC when I connect to the IP. Please advise.

@diy-o-sphere Now DWC is offline. panel shows the web server started but blank screen when I connect to the IP. I am not trying to upgrade from 2 to 3 just 2.02 to the latest 2 to use the magnet sensor.

@diy-o-sphere What? Please elaborate. Is there a better description?

Software Information
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later + DueX5
Firmware Version: 2.02(RTOS) (2018-12-24b1)
WiFi Server Version: 1.22
Web Interface Version: 1.22.6
Web Interface by Christian Hammacher

Bought an magnet filament sensor for my Railcore and would like to update to the latest firmware. Using DWC the Duet2CombinedFirmware.bin is downloaded, install seems to run but no restart and no change in reported version after manual restart. Please advise.

@t3p3tony said in Laser Filament Monitor:

@bluedust The monitor does not like that PLA, or at least your enclosure. do you have any other PLA to check with as I and other testers have generally done OK with PLA, most of the problematic filament has been PETG.

For me PLA or PETG it doesn't matter the range of movement detected varies dramatically. I set it to 2-130% over 3mm now. Otherwise prints stop every few seconds-minutes. What impact has increasing the measured distance? Anyway the sensor already saved a few prints when filament entangled, ran out or slipped because I forgot to tension the extruder gear.

Anyway to ensure defined IP for the Duet? Octoprint doesn't have the problem for some reason

@dc42 said in PC connects fine to Duet-MAC won't see the server.:

http://

Thought of that. No browser works with MacOS to connect to Duet. How do you check IP of duet without connecting through usb?

Weird Issue. Windows connects fine through Chrome to the Duet2 web interphase. When I put in the IP address of the duet into chrome on the MAC connection just times out. Any one knows what is going on?

Thank you so much, that explains all perfectly. I see this: Duet3D laser filament monitor on input 3, enabled, allow 40% to 120%, check every 3.0mm, current pos 2.8, brightness 95, shutter 17, measured min 43% avg 92% max 102% over 2269.5mm

@dc42 The reporting of the parameters is through the console is there a way to get this in the web interphase? It is reporting: Duet3D laser filament monitor on input 3, enabled, allow 40% to 120%, check every 3.0mm, current pos 2.8, brightness 95, shutter 17, measured min 43% avg 92% max 102% over 2269.5mm. Trying to make sense of the output? I integrated the sensor into my print head with the ability to ad different materials as a background to see if I can improve on detecting different materials.

@dc42 Thanks. It seems to be working printing is stopped occasionally reporting too little movement of extruder D0 and I have to resume printing manually? When I upload files they are always saved to the sd cards through the web interphase. Do you mean starting the print from there? Don't use the sd card reader on the panel duet.

Where do you get the values? I installed a laser filament sensor and enabled it. It seems to be working as printing stops sometimes reporting too little movement of the extruder and I have to manually resume printing. From the doku I can't figure out how this is supposed to work. I wish the Duet guys would bother to explain in more detail how one uses this when new to Duet.

@dc42 ok I ad S0 or S1 so can disable or enable the sensor. Still don't see how anything useful is done with sensor? Should there be a return in the web interphase?