Best posts made by elmoret

https://www.filastruder.com/products/duet-magnetic-filament-monitor

/shameless plug

Hi gencab, just now saw this. I know you didn't buy from us, but if you contact us (Filastruder) using the contact page, we might be able to help.

Sorry you had a bad experience with M3D, seems you are not alone unfortunately.

Detailed documentation for what you're trying to do doesn't really exist for the simple reason that your approach is an odd one. Instead of using the Duet PT100 daughterboard like most everyone would do, you're using a third party board.

This is like buying a Honda Civic, and then then being upset that Honda does not provide detailed instructions for installing a Ford engine into the car.

I don't know why you spent 30 minutes of searching to find that page, if you go to the Duet documentation, type in "PT100" in the search box, that page you linked is the first result.

At any rate, the info in the table does match, though it is for generic PT100 boards and Duet 0.6/0.8.5. Assuming you have this specific board from Adafruit:

https://www.adafruit.com/product/3328

Then look at the schematic for the Duet 2 Wifi:

https://github.com/T3P3/Duet/blob/master/Duet2/Duet2v1.04/DuetWifi_Schematic_v1.04.pdf

Connect the Vin pin on the Adafruit board to pin 8 of the SPIO temperature sensor board connector and so on.

@dc42 said in Duet3D-2 New install uncertainties:

I think the reason nobody has ported any other firmware to the Duet is that RRF is so hard toi beat. Whereas RRF has been so successful that others have already ported it to LPC1768/1769 boards, and a port to STM-based boards is under way.

Gotta say I agree with that. No way I'd go back to Marlin after experiencing RRF.

@64bit Source is here:

https://github.com/Fusion3-Design/1.18.1-Source-Code

@onerob That'll do it!

I've gotta say, I appreciate the honesty. Happy to knock $50 off a Duet 3 6HC if you want to purchase one from us (Filastruder). Just email support at filastruder.com with a link to this thread, and you'll get a coupon code.

@random_task_1 Your pinout is incorrect.

I've taken the photo in the documentation, and overlaid your wire colors in text. The 4 pin side represents what your 4 pin side is. The 5 pin side represents what your 5 pin side should be. Looks to me like you've got the RX/TX flipped, which is why your screen is powering up (5v and GND are good) but not communicating.

Got the board from @srgallagher13 , it does not present as a USB port. Diag LED is on continuously. We'll work on it and advise if we come up with a solution, in the meantime we've provided him with a Duet WiFi instead.

@t3p3tony Just wanted to chime in that as a reseller working with many companies, Duet3D has done an outstanding job of navigating supply chain issues. Well done!

@nhof I think that's your comment in the resume.g file in Joel's video

I like to use a flathead/slotted screwdriver between the fuse body and the terminals, prying one terminal at a time.

I'm not big on self-advertisement, but also didn't know how to get the word out on something like this.

We've recently sourced some PanelDue 5i/7i touch panel replacements, for those of you that have cracked yours. Of course it makes us more money if you buy a whole new PanelDue but we are trying to take the consumer and environment friendly approach of providing spares.

So, here you go:

https://www.filastruder.com/products/paneldue-5i-7i-touchscreen-glass-only

And we have a few refurb PanelDues as a result:

https://www.filastruder.com/products/clearance-paneldue7i

Hope this post is OK, feel free to delete if not!

@srgallagher13 I know you didn't order from us, but email us at Filastruder and we'll see what we can do to help:

https://www.filastruder.com/pages/contact-us

If its a legitimate Duet 2 Wifi (not a clone), and you want to trade for a Duex5, contact Filastruder, we can do that.

A photo seems like it'd be helpful here.

Filastruder's preorder available here:

https://www.filastruder.com/products/duet-3-mainboard-6hc

2660s can handle 30v max, the 25v rating on the Duet is to provide headroom.

https://www.trinamic.com/fileadmin/assets/Products/ICs_Documents/TMC2660_datasheet.pdf

@remzirecep Yelling for help is not a path to a solution.

Posting the aforementioned photo is a path to a solution, as is posting the changes you've made to the code.

You're getting a reply from the lead firmware author. Maybe a little appreciation for that would be helpful too.

@onescentpro said in New Duet WiiFi board:

Thanks for the response. Ooznest has a block on the sd card so I can't move any files. They deleted everything when they refunded the price of the board to me. So basically I am starting from scratch with the new Duet board from Filaster. They do not give support for the board as they promised. Now I am stuck with a board That I can't get going.

Woah, this is simply not true.

Before you purchased, you asked if we would support the Workbee. I said we could not, because we don't have a Workbee, and have no experience with it, but that we could provide general support for the Duet 2 (getting connected, etc).

You then emailed that you "got everything downloaded and got the control panel activate but I can’t get the router to move.".

We don't have a Workbee, so we aren't in a position to figure out what could be preventing you from moving it - we have no experience with how a Workbee is wired.

A "block on the SD card" doesn't make any sense, if the Duet can read it, your computer can read it. Plus, they even post it online, a s linked above.