That's right dc42. I have a CoreXY and defenetly it's a problem on DWC latest release. I did the downgrade and now it's working fine. Thanks
Posts made by DR8
-
RE: I can no longer Load/Unload different filaments
-
RE: I can no longer Load/Unload different filaments
I hve tried again and again. I think was the wak connection of my wifi router. Now I have uploaded and yes the topic problem was solved. But Now i have another one. When i want o move the head X+10mm the head goes -X and -Y direction. When I press Y+10 the head goes -X and +Y direction. My config.g is this
; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes forwards
M350 X64 Y64 Z64 E32 I1 ; Configure microstepping with interpolationI have tried:
M569 P0 S0 ; Drive 1 goes forwards
M569 P1 S0 ; Drive 2 goes forwardsM569 P0 S1 ; Drive 1 goes forwards
M569 P1 S0 ; Drive 2 goes forwardsM569 P0 S0 ; Drive 1 goes forwards
M569 P1 S1 ; Drive 2 goes forwardsM569 P0 S1 ; Drive 1 goes forwards
M569 P1 S1 ; Drive 2 goes forwards -
RE: I can no longer Load/Unload different filaments
it's says error on the bar where it should be 10 20 30 99% uploading. It uploads until 22 or so and then it shows error
-
RE: I can no longer Load/Unload different filaments
Oh, ok. Got it. So i have downloaded the latest firmware, server and web control from here https://github.com/dc42/RepRapFirmware/releases and when I try to upload and install the firmware via web interface I gor error. Why is that?
-
I can no longer Load/Unload different filaments
Hi,
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.0(RTOS)RC5 (2018-05-22b1)
WiFi Server Version: 1.21
Web Interface Version: 1.21.1-RC4After the update on this firmware version I can't Load/Unload/Change filaments from my tool head. I have double checked and the right macros for the filaments are present in the "Filaments" folder. What can I do?
Thanks!
-
RE: Error: M24: Cannot resume while power voltage is low
Oh s..t,
Now I see the problem.I have another duet on other printer witch is on 24V. Jeez, I'm gonna loose my head one day. Thaks a lot.
-
RE: Error: M24: Cannot resume while power voltage is low
Yes I do. Here's the line from my config.g
M911 S20.5 R22.0 P"G91 M83 G1 Z3 E-3 F1000"
-
Error: M24: Cannot resume while power voltage is low
I have a duet wifi board with this configuration:
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.0(RTOS)RC5 (2018-05-22b1)
WiFi Server Version: 1.21
Web Interface Version: 1.21.1-RC4I have installed a Runout filament sensor. It's an endstop. After it triggers, I insert a new filament and when to press Resume, I got this error:
Error: M24: Cannot resume while power voltage is low
The input voltage on the board is fluctuating between 11.7 and 12.2V. This error occur even if I intentionally press the Pause button.
-
RE: Problem by connecting to duetwifi from browser
Unfortunately, i was not so careful and I did not had the WWW folder on the SD card. That's why it did not work.
-
Problem by connecting to duetwifi from browser
So the problem that i have is that I can't connect with the IP adress to the duet board. I followed all the steps presented here: https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7?lang=en. Panel Due shows ,,Connected" Wifi module is connected to the access point........ IP adress:......... And when I type in the browser the specific IP adress i get no page found
-
RE: Problem with calibration cube
The belt is tight and I retighten all the screws, pulleys and so on. I have changed the values for X=220 and Y=230 just to see what's happening. I'll post the result.
-
RE: Problem with calibration cube
So after I printed a calibration cube of 60x60x60 at 205 degree, Pla, 2 perimeters, 3 bottom layers and 6 on top the dimensions are: X=59.2 Y=59.11 Z=60. These are middle measurements. If I measure the bottom I get: X=59.3 Y=59.23
-
RE: Problem with calibration cube
Ok, I'll go for 50x50x50 and post the results.
-
Problem with calibration cube
Hi,
I have an Hbot with 1.8 degree nema 17 motors. I run them at 32 microsteps. My problem is that i have a hard time calibrating steps/mm. I have modeled a 30/30/30 mm cube and printed it with 3 perimeters, 3 bottom layers and 6 on top. My steps/mm on X and Y were set to 204 and the cube came out 29.7 on X and 29.5 on Y. So i made the calculus ( 30/29.7=1.01 ; 204x1.01=206.4)for X and (30/29.5=1.1069 ; 204x1.0169=207.4) . After this calibration the cube came X=29.7 and Y=29.6
I should mention that before all of this I have calibrated my extruder steps/mm and the cubes were printed with the same material (PLA) at the same temp(205) as when i have performed the extruder calibration. Any ideas?
Thanks.
-
RE: Top layer problem
I think you should be posting this on the Cura forum (https://community.ultimaker.com/), not here, as the problem is more likely to be a slicer setting rather than a problem with the Duet config.
Sorry, you're right. I'm gonna post there.
-
Top layer problem
Hi guys,
I'm using Cura 3.04 and I don't know why but I have a problem with my top layers. The problem is present in different objects but when i print a test rectangle i got awesome top layers. What's happening? All the objects have the same infill density witch is 10% linear. Tnx!
-
RE: Where is the quick start guide for this board???
Well to be honest it wouldn't be bad for who is new to have a guide on the terms and meanings. Which I have been looking for on the web but have yet to find. Well all the pieces are there but mixed in with other things so its harder to find and figure things out. Like a puzzle you have to put all the picese together to see the big picture.
Some things like motor drive 0 forward is simply if you know from what point of view.
Been working with software from when there was no monitor or mouse, and Steve Jobs was in his garage, but a typewriter so yes if you keep looking you can find the answer. Even if right now I would rather be printing than figuraing things out.
I have a 2 3D printers Solidscape which i can take apart and put back together after using them so long, but I never built them.
I'm still trying to understand why my endstops don't stop the motors which I'm sure I saw something the other day when looking for somethings else.
So yes more than a detailed manuale which is impossible seeing the fast evolution of the board a guide to the terms and meanings.
and how to apply them would be better.Wow…. you have lived trough two awesome breakthroughs in technology. I wish to see everything go electric and see people living on Mars in my life :)))