Seems i had a short in the wiring cable to the extruder and fried the duet wifi motor chip.
lots of smoke from the board and visible damage (burn damage to the chip)
but it still is putting out console messages
Error: short-to-ground reported by driver(s) 3
can i use the drive 4 E1 connector for driving the extruder again?
little afraid to just switch over .
but it should be possible to remap this?
thanks
@jay_s_uk
but i never seen such warning.. why does it come up now?
hi i got a question regarding this error.
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature could reach 576C
i did the following changes to my creality cr 10 s Pro version frame.
removed old stock motherboard and inserted the duet motherboard.
used the flat cable and refitted all cables so it's still plug and play.
used a bondtech DDS with pancake stepper and E3D V6 kit.
now when i start the printer. its working but i get a error
i did a pid tune and inserted the outcome in the config.g
but i think i made more errors so thats why i put in the config i have.. hope u can see more errors
and help me a bit with them please. .
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet-Wifi-CR10SPRo" ; set printer name
M918 P1 E4 F2000000 ; configure direct-connect display
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E415 ; set steps per mm
M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X900 Y900 Z900 E600 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z260 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop
; Z-Probe
;M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
;M557 X15:215 Y15:195 S20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as PT1000 on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.405 C736.635:736.635 D7.91 S1.00 V24.2 B0
M307 H1 R1.864 C159.2 D8.88 S1.00 V24.1
M140 H0 ; map heated bed to heater 0
M143 H0 S60 ; set temperature limit for heater 0 to 60C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e1temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S260 ; set temperature limit for heater 1 to 260C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
T0
; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
config.override
; config-override.g file generated in response to M500 at 2023-01-21 19:30
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 R0.405 C736.635:736.635 D7.91 S1.00 V24.2 B0
M307 H1 R1.864 C159.2 D8.88 S1.00 V24.1
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00
M486 S-1
homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-305 Y-305 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-305 Y-305 F240 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-265 F240 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning
start.g
T0M92 E415; set new E-step value for Bondtech BMG Extruder
homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-305 F3000 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000 ; go back a few mm
G1 H1 X-305 F240 ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
homey.g
; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Y-305 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000 ; go back a few mm
G1 H1 Y-305 F240 ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
homez.g
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Z-265 F3000 ; move Z down until the endstop is triggered
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning
tried it and the comment is gone. so that is solved , i used some other cables
but now if i press level x then z moves . i have managed to break it once again
can someone please help me fix the config files.
i have to map the steppers but i have no idea..
i have one x stepper
one y stepper
And two Z motors.. there connected to the dual output ports on my duet2 wifi
i also like to know what are the files on my sd card doing.
i have
config-override
config.bak
config.g
what is the correct file?
i want to reuse the old endstops (two wires mechanical ones)
the rest is hardware used from my older cr10 printer..
below is the config i used on the old printer but its not working although it also creality cr10
if someone can help me out, that would be appreciated a lot..
code_text ; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Butcher" ; set printer name
M918 P1 E4 F2000000 ; configure direct-connect display
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E400 ; set steps per mm
M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E600 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z260 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop
; Z-Probe
;M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
;M557 X15:215 Y15:195 S20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as PT1000 on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.116 C633.1 D0.47 S1.00 V11.8 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S60 ; set temperature limit for heater 0 to 60C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e1temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S260 ; set temperature limit for heater 1 to 260C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
T0
; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
@droftarts ok thank u for responding.. when finished from work i will try it and post the outcome.. once again thank u
hi all
and first of all best wishes and a healthy 2023
i have a question.. i have a duet 2 wifi and i have a used printer frame. (gift because broken motherboard ) really neat looking creality sc10s pro i want to use the Duet 2 wifi that i have here.. i am totally rewiring it. inc flat cable 
now the printer has standard creality cr 10s pro steppers and i have problems finding info about the steppers. and what settings to use with the online config tool.
the text on the stepper is bj42d22-23
i tried multiple versions of the online config generator but the steppers do move . but keep making weird noises and making lots of noise. and it's giving errors like A motor may be disconnected reported by driver. that error that has to do with faulty wiring .but i checked the old wiring and bought new cables with connectors but no luck, . does anyone have any clue what i am doing wrong here.. ps i am using the 24v volt to power the duet.. as far as i know this can't be the problem because the cr10s pro is stock 24volt. hope that some of u can point me in the right direction.. thanks
i have noticed that one also.. so if the light flash fast its pid if its slowly on and off its bang bang..
@Argo said in blob related:
cooling fan running and at
Hi Argo
yes the fan is running the one cooling the extruder is always on.
and the other fan the one that is blowing at nozzle is
on first layer to bed it is off. 0 prorcent
40 procent at second layer.
than 50 at third
and 100 at fourth layer
hi all
got a question regarding the weird looking prints
i think its some sort of blobbing?
tried other slicers also
prusaslicer
cura
and back to simplify3d
changed layerhights, temps checked the belts. did a new pidtune.. leveleld the bed again.
its after i changed some new hardware
that is Bondtech direct drive with pancake stepper and v6 hotend
i have done the following so far, pidtuning other pla spool, leveled the bed a lot.
adjust the retractings was on 6 now on 2 but no luck
Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.2.2 (2021-02-11)
Duet WiFi Server Version: 1.22
hope that someone over here can help me out a bit.. 
thank u
nevermind i removed al the wiring from the bltouch and i am going back to manual adjusting..
anyway thanks all
M280 command do work.
m401 and 402 does nothing.
and thats it..
can this be due to the fact i have antlabs v3 probe?
@Phaedrux said in old bltouch is not working with RRF?:
printer just to save some crashes.
i did try to do the static test but no joy
i have to shut it down because its crashing in the bed.
M280 P0 S10 and M280 P0 S90 do work on the probe
i tried the dynamic test also (just to be sure) but x homes en y home is working
but pressing Z is a bed crash..
i have to be the most challenging and annoying noob to u guys right now 
@Phaedrux that was error bad command in homey.g
but that was due to some left over commands that where there..
y is homing again. x is homing again Z is killing my heatbed so i have to switch it of fast. .
Phaedrux You don't need this stuff and it won't work. To use the probe to home Z you only need the G30.
so literary delete all lines in there except G30?
@droftarts i was in the morning on the photo on the other pin. after that i changed it to
pin 18 heater 5
the deleted line is due to the fact i had so much problems getting the probe to activate i used my old config files due to the fact i have problems understanding some explainations... i am sorry about that its on my end here.. sorry once again to trouble u guys.
i think its better to remove all and manualy level the bed again.. it just not working
i think i just broke my printer.. its making al weird noises and its saying Error bad command1 on the screen
i was as far that my probe was reacting ,but its not working anymore..
sorry from the Cloghopper that knows how to print but not to work with codes.. 
homey.g
; called to home the Y axis
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Y-315 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000 ; go back a few mm
G1 H1 Y-315 F240 ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Mar 17 2021 16:20:28 GMT-0600 (Central Standard Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first probe point
G30 ; home Z by probing the bed
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
; now home z - still in absolute positioning, z is still at least 5mm from the plate, and T1 is selected
; front/center adjustment screw is at X1.1 Y-69.2 and the probe is offset from T1 by X-73.2 Y-0.8
G1 X74.3 Y-68.4 F6000 ; position the probe over the front/center screw adjustment point (offsetting from T1)
G91 ; relative positioning
M401 ; deploy the probe
G1 Z-155 F6000 ; quickly move Z down, stopping at the probe (possible because of M574 Z1 S2 in config.g)
G1 Z5 F1200 ; immediately move the nozzle 5mm away from the build plate
M401 ; make sure the probe is deployed still
G30 ; slowly probe at the current position and set Z to the trigger height (this sets Z to 0.83 when the trigger happens)
M402 ; retract the probe
; set Z position to axis minimum (you may want to adjust this)
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning
and my config.g
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
M564 H0 allow axis movement before homing.
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"CR10 on steroids" ; set printer name
M918 P1 E4 F2000000 ; configure direct-connect display
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E415 ; set steps per mm aangepast voor directdrive bondtech
M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E600 I50 ; set motor currents (mA) and motor idle factor in per cent aangepast voor bondtech de E was 1000 ipv 600
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X310 Y310 Z260 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop
:Z-Probe
M558 P9 C"^zprobe.in" H3 F120 T3000 ;
G31 P500 X-32 Y13 Z2.9 ; Set Z probe trigger value, offset and trigger height
M557 X15:225 Y15:225 S20 ; Define mesh grid
;M915 X Y S5 R2 DIT STOND OP ACTIEF
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.159 C614.2 D0.51 S1.00 V12.4 ; disable bang-bang mode for the bed heater and set PWM limit pid tuning command voor cr10 bed
M140 H0 ; map heated bed to heater 0
M143 H0 S75 ; set temperature limit for heater 0 to 75C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S275 ; set temperature limit for heater 1 to 275C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
homey.g
; called to home the Y axis
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Y-315 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000 ; go back a few mm
G1 H1 Y-315 F240 ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
yes if i start up the board. and use commands
M280 P0 S90 M280 P0 S90 than it goes up and down and its reacting on the zprobe number its going to 1000
but i can not use the homing on z than it still forcing on my bed and the stepper is making a grinding noise.
can it be that i need a 240 Ohm resistor
its a creality v1.3 bltouch
if so no problem but i have to order some resistors lol
@droftarts said in old bltouch is not working with RRF?:
M558 P9 C"^zprobe.in" H3 F120 T3000
ok i have movement in the probe
the wirings where wrong indeed
and the pin reacts on
M280 P0 S10
M280 P0 S90
yes yes yes thank u so much!!!!
no i have to read the how to level bed with blt parts
thank u once again Phaedrux for helping me out here. again. 
But if i knew it was this difficult on the software part i have never use the bltouch and leave my printer as is..
but i do want to thank u for pointing me out once more.
can u please check my files for me. i am even wanting to pay for it
but i have no idea what i am doing wrong..
i will give my settings also
youtubemovie what is happening to my printer now.
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
M564 H0 allow axis movement before homing.
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"CR10 on steroids" ; set printer name
M918 P1 E4 F2000000 ; configure direct-connect display
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E415 ; set steps per mm aangepast voor directdrive bondtech
M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E600 I50 ; set motor currents (mA) and motor idle factor in per cent aangepast voor bondtech de E was 1000 ipv 600
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X310 Y310 Z260 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop
:Z-Probe
M558 P3 C"^zprobe.in" H3 F120 T3000 ; FW v3 BLTouch connected to Z probe IN pin
M950 S0 C"exp.heater5"
G31 P500 X-32 Y13 Z2.9 ; Set Z probe trigger value, offset and trigger height
M557 X15:225 Y15:225 S20 ; Define mesh grid
M915 X Y S5 R2
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.159 C614.2 D0.51 S1.00 V12.4 ; disable bang-bang mode for the bed heater and set PWM limit pid tuning command voor cr10 bed
M140 H0 ; map heated bed to heater 0
M143 H0 S75 ; set temperature limit for heater 0 to 75C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S275 ; set temperature limit for heater 1 to 275C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
retractprobe.g
; retractprobe.g
; called to retract a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Mar 17 2021 16:20:08 GMT-0600 (Central Standard Time)
M280 P0 S90 ; retract BLTouch
deployprobe.g
; deployprobe.g
; called to deploy a physical Z probe
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Mar 17 2021 16:19:53 GMT-0600 (Central Standard Time)
M280 P0 S10 ; deploy BLTouch
zprobe.g
; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid
homex.g
; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-315 F3000 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000 ; go back a few mm
G1 H1 X-315 F240 ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
homeg.g
; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Y-315 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000 ; go back a few mm
G1 H1 Y-315 F240 ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning
homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Mar 17 2021 16:20:28 GMT-0600 (Central Standard Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first probe point
G30 ; home Z by probing the bed
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning
Z-Bot CoreXY Build | Thingiverse Profile]
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 21:51:16 GMT+0100 (Midden-Europese standaardtijd)
[[language]]
; now home z - still in absolute positioning, z is still at least 5mm from the plate, and T1 is selected
;
; front/center adjustment screw is at X1.1 Y-69.2 and the probe is offset from T1 by X-73.2 Y-0.8
;
G1 X74.3 Y-68.4 F6000 ; position the probe over the front/center screw adjustment point (offsetting from T1)
G91 ; relative positioning
M401 ; deploy the probe
G1 Z-155 F6000 ; quickly move Z down, stopping at the probe (possible because of M574 Z1 S2 in config.g)
G1 Z5 F1200 ; immediately move the nozzle 5mm away from the build plate
M401 ; make sure the probe is deployed still
G30 ; slowly probe at the current position and set Z to the trigger height (this sets Z to 0.83 when the trigger happens)
M402 ; retract the probe
; set Z position to axis minimum (you may want to adjust this)
; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning
[ok the only time the probe moves is during reboot it clicks two times and than stays red;
i have read the v3 manual but got some questions. i having problems with technical english so i am sorry
used the copy paste from manual it is a little better for me to explain
i do not use pin 9 but i use pin 3 so than it will be M558 P3 C"^zprobe.in" H5 F100 T2000** right?
If using pin zprobe.in then must include the ^ character in front of the pin name to enable the pullup resistor.
i can not make anything out of this sorry .
Create a GPIO/Servo pin index using your chosen control pin:
M950 S0 C"exp.heater3"
i think i leave this default?
In this example we chose to attach GPIO/Servo index 0 to pin exp.heater3 on the expansion connector of a Duet WiFi or Duet Ethernet. On a Duet Maestro you would use C"zprobe.mod" in the M950 command.
. Set up the probe offsets, trigger height and trigger value in G31:
G31 X20 Y0 Z3.3 P25
In this example the trigger height is 3.3mm (you will need to measure it) and the probe is offset from the head reference point by 20mm in the +X direction.*
its difficult but i can measure it later i want to get it to work first so that the probe does move .
6. Create the deployprobe.g and retractprobe.g macros as described for using RepRapFirmware 2. The P value in the M280 commands should be your chosen GPIO/Servo index. You do not need the I1 parameter.
OK i make two new files in the called deployprobe.g and retractprobe.g
i deleted the old ones and there are new empty files in there. i think this is the outcomes if i have done the testing and measurments right?
ok and the new chapter called Commissioning & Testing (RepRapFirmware 3)
but this is for later..
once again i am sorry but i have problems understanding technical english. thank u for the help guys..
oh lol that aint good than..
ok i will try to fight my way in to the commands for latest firmware
thank u sir!