Posts made by daoust

Thank you very much, it was not easy for me but atleast, I m connected to my wifi extender, not it is time to fine tuning

Hi after some working to try to change my network, cancelling the older network, I fail to update my new network from YAT or even from macro so I decided that maybe if I erase my duet, it should be fine.

Now that the duet is erase, YAT can t send g code or m code to the duet so I download Bossa and follow the procedure to push the firmware to the duet wifi.
It say to erase all, lock and boot from flash than choose the firmware but when I choose 1 of the firmware available from the last version for the duet wifi 2 , it still can t be controll from YAT and I can t push anyother bin file because it say it is lock . So I wonder what files should I write with Bossa to the duet? Should I install only one file or I install the wifi modul also and other files aswell?

So Basicly, how from a erasse duet wifi with the usb connected can I write the new firmware to the duet?

Thank you

@Phaedrux thank you very much but I allready try that option also. I wish for any other way to force a setting without the need of PID autotune🥲

Small update to this post. I was previously using 500w heater with the old version firmware and was easily heating my chamber . Since the new firmware, it was not able to heat the chamber higher than 40 deg C. I try to do a auto tune pid of the chamber and it allways fail to finish the auto tune. The heated chamber is set in bang bang configuration. The heater is working on 110v so the duet control arelay 24v to 110v from the second heater from the duet card. So at some point, I decided to update my heater to 700w heater and I put bigger fan to have more airflow. Final result, I was able to heat up to 40deg C than fail. Now I don t know what to try. I don t belive a 1000w heater will be my solution because it was working fast with the 500w before the firmware update. It should just be faster now with the 700w and bigger fan

@dc42 I always use a sdcard because I need a wifi booster but I don t have any. I got some trouble lately that make me belive my sd card is the only thing that where not try yet.

@infiniteloop here is the file. it is available for 7 days https://www.transfernow.net/dl/20230120EGawtxia

Thank you

@infiniteloop the m122 was done after the error hapen, the printer was never close after the event.

I will look at dropbox to send the file. Now I m suspecting a bad sd card maybe

Here is the line that should have fail

so here is the m122 , for the gcode, it say my file size is too big too share, so how to ? file size is
29 921kb

console.txt

@daoust ![alt text]

@infiniteloop I tested 3 differents gcode viewer, all 3 have the same line count of 941 463. All 2 mark ; end of gcode at line 941 443. After looking for a long gcode line, I don t find anything longer near the midle of the print. Should I try again the same gcode to see if the probleme still there?

@infiniteloop it stop after 6h30 min in a 10 to 11h print

@infiniteloop I use cura 5.0 with reprap firmware.

It almost stop in mid print but when I open with notepad++ it only have 941463 line of command for the complet gcode so I don t understand how it can be a probleme with the line 995655

I was in the midle of a print and I got this message: error, gcode file too long. Any idea what to look for to fix this problem? I m on the newest firmware.

Thank you

@jens55 the heater is working. It reach 40deg temperature only with this heater and no help from the built plate

@Phaedrux old firmware was 2.02, new firmware is 3.3.13. Yes I try PID autotune and it allways fail because it take too much time

Hi I have a duet wifi that was previously running a outdated firmware that I update to a newer version.
Since the new update, I can t no more raise the temperature of my heated chamber more than 40deg C. Before new firmware, it was easilly going to 65deg C and more. The heated chamber is set in bang bang with a 110v 300w ptc heater plug on a relay that is control from the heater number 2. I was able to mesure 115v@60hz. I try to run a pid autotune as recomended and it allways fail. Now, I out of idea on what to do and I don t want to run the old firmwarw again.

Do you have some idea on what to do?

Thank You All and merry Christmas

@dc42 so it fix my initial problem but when I try to do pid autotune of the heatead chamber, it take a full day and than fail.

Before the firmware update, my heated chamber was really fast, not even comparable. Now it is so slow and it can t finish a PID autotune without failling. Whan should I try???!

Thank you20221121_172239.jpg

Thank you

@dc42 so I try a PID autotune and it a fail.
The firmware is the new one.

I snen the comande M303 H2 S50 and the heater was not able to heat fast enougth

Is there something wrong with my comande?

Thank you