Posts made by antoine.voiry

Hello
i am trying that.
Antoine

Thanks so much!

The bed probing will be fine, and then I keep the printer on with no print and another bed level will be completely off.

I am still getting the e0heat error. In the config override, I only have the PID tune, I can post the file if needed.
I would not be surprised if I have some odd things in the config, I have been tweaking this config for at least 5 years.

Here is home x

G91                ; relative mode
G1 Z1 F600 H2     ; lift Z relative to current position
G1 X-240 F2000 H1  ; move up to 240mm in the -X direction, stopping if the homing switch is triggered
G1 X4 F1000         ; move slowly 4mm in the +X direction
G1 X-5 F1000 H1         ; move slowly 10mm in the -X direction, stopping at the homing switch
G1 Z1 F200  H2      ; lower the head again
G90                ; back to absolute mode

home y

G91                ; relative mode
G1 Z0.5 F200 H2     ; lift Z relative to current position
G1 Y-320 F3000 H1  ; move up to 240mm in the -X direction, stopping if the homing switch is triggered
G1 Y4 F600         ; move slowly 4mm in the +X direction
G1 Y-5 F600 H1         ; move slowly 10mm in the -X direction, stopping at the homing switch
G1 Z-0.5 F200 H2       ; lower the head again
G90                ; back to absolute mode

home z

G91                ; relative mode
G1 Z5 F200 H2        ; raise head 4mm to ensure it is above the Z probe trigger height
G90                ; back to absolute mode
G1 X100 Y150 F3000 ; put head over the centre of the bed, or wherever you want to probe
G30                ; lower head, stop when probe triggered and set Z to trigger height

Example start GCODE

G90
M83
M106 S0
M140 S65
M190 S65
; probe bed
M300 s1500 p500 ; BIP probe starting
G32 ;probe bed
M300 s1500 p500 ; BIP probe ending
; probe bed end
; set temperature
M109 S215
; wipe extruder sequence
G1 X15 Y10 Z0.2  F3000 ; avoid binder clips
G1 X130 E12 F500 ; prime line
G1 X145 F100 ; slow wipe
G92 E0                  ;zero the extruded length
; process P3STEE PLA1.75
; layer 1, Z = 0.240
T0
G1 E-1.4000 F2100
; feature skirt

I corrected the config.g now looking as follow, but still getting some errors unrelated to my issues.

; Configuration file for p3STEEL

; Communication and general
M111 S0                             	; Debug off
M550 pp3steel		; Machine name and Netbios name (can be anything you like)
M552 S1				; Enable WiFi

; misc settings
M555 P2                           	; Set output to look like Marlin
M575 P1 B57600 S1			; Comms parameters for PanelDue

; setting for all axis
G21                                 	; Work in millimeters
G90                                	; Send absolute coordinates...
M83                                 	; ...but relative extruder moves

; Axis and motor configuration
M569 P0 S0				; Drive 0 goes forwards (x)
M569 P1 S1				; Drive 1 goes forwards (Y)
M569 P2 S1				; Drive 2 goes forwards (z)
M569 P3 S0				; Drive 3 goes forwards (e1)
M569 P4 S1				; Drive 4 goes forwards (E2)

; microstepping and homing switch config
M350 X16 Y16 Z16 E16 I1             ; set 16x microstepping with interpolation


M574 X1 S1 P"!xstop"   ; X min active high endstop switch
M574 Y1 S1 P"!ystop"   ; Y min active high endstop switch
M574 Z1 S1 P"zstop"   ; Z min active high endstop switch


; Motor current and acceleration
M906 X1000 Y1200 Z1200 E1200 I30		; Set motor currents (mA) and increase idle current to 60%
M84 S60 ; Set idle timeout

M201 X3000 Y3000 Z15 E3600		; Accelerations (mm/s^2) 
M203 X6000 Y6000 Z100 E1200		; feedrate  (mm/min)
M566 X1800 Y1800 Z180 E300		; Maximum instant speed changes mm/minute
; M210 X5000 Y5000 Z60  			; set hming feedrate

; steps per mm
M92 X79.01 Y76.04 Z3298.92  ; Set axis steps/mm
; M92 E415:415                          ; set extruder 0 and 1 steps/mm
M92 E415



; Thermistors
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.06e-8 ; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
M950 F0 C"fan0"  ; Fan 0
M140 H0 ; the bed heater is heater 0


M143 H1 S270 ; Set maximum heater temperature to 270C
M143 H0 S115 ; Set maximum heater temperature to 270C



; Tool definitions
M563 P0 D0 H1                       	; Define tool 0 old
M571 P"e0_heat *" S1.0
G10 P0 S0 R0                        	; Set tool 0 operating and standby temperatures



; Z probe and compensation definition
M558 P1 C"^zprobe.in"  X0 Y0 Z1 H5 F500 T3000    ; smart IR Z probe, used for homing Z axis only, dive height 3mm, probe speed 200mm/min, travel speed 5000mm/min
G31 P500 X15 Y3 Z0.40        ; set threshold and offsets (we were at 0.50 BEFORE ADJUSTMENT)

;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0                   	; Axis compensation here


M206 X0 Y0 Z0
M208 X0 Y0 Z0 S1 				; set minimum Z
; max travel and origin
M208 X215 Y310 Z200 

;
T0					; select first hot end

M570 H1 P20 T30 

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

diagnostic
```
M98 P"config.g"
Error: Unknown pin name 'e0heat*'
Error: Heater 2 not found
Error: Heater 3 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found
Error: Heater 7 not found

@Phaedrux said in Struggling in setting up the bed compensation:

M122

Hello
So
M122

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4S4-6J1DG-3S46N-TPHRY
Used output buffers: 3 of 24 (12 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93788 of which 60 recycled
Exception stack ram used: 584
Never used ram: 8660
Tasks: NETWORK(ready,708) HEAT(blocked,1224) MAIN(running,1904) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 03:48:29 ago, cause: software
Last software reset at 2020-12-16 19:01, reason: User, spinning module GCodes, available RAM 8708 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 31.6, current 36.0, max 40.1
Supply voltage: min 13.3, current 13.9, max 14.1, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/1023
Driver 1: ok, SG min/max 0/1023
Driver 2: ok, SG min/max 155/959
Driver 3: ok, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-12-16 22:49:56
Cache data hit count 4294967295
Slowest loop: 87.70ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.5ms, write time 9.6ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 165, MinFreeDm: 85, MaxWait: 5148849ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 3102, completed moves: 3063, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X111.801 Y162.049 E0.0048" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 46.35ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 60:01:94:09:bc:4e
WiFi Vcc 3.44, reset reason Unknown
WiFi flash size 4194304, free heap 23568
WiFi IP address 10.0.0.19
WiFi signal strength -62dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

M98 P"config.g", I think that shows already some issues. i'll look into that.

Warning: M210: Command is not supported
Error: in file macro line 44 column 10: M92: array too long, max length = 1
Error: Unknown pin name 'e0heat*'
16/12/2020 à 22:51:22	Error: Heater 2 not found
Error: Heater 3 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found
Error: Heater 7 not found

and last the home file.

G91                ; relative mode
G1 Z1 F200  H2       ; raise head 1mm
G1 X-240 Y-340 F2000 H1  ; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 X4 Y4 F1200      ; move slowly 6mm in +X and +Y directions
G1 X-5 Y-5 F1000 H1    ; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90                ; back to absolute mode
G1 X105 Y155 F3000
G30                ; lower head, stop when probe triggered and set Z to trigger height

I forgot my settings are as follow
config

; Configuration file for p3STEEL

; Communication and general
M111 S0                             	; Debug off
M550 pp3steel		; Machine name and Netbios name (can be anything you like)
M552 S1				; Enable WiFi

; misc settings
M555 P2                           	; Set output to look like Marlin
M575 P1 B57600 S1			; Comms parameters for PanelDue

; setting for all axis
G21                                 	; Work in millimeters
G90                                	; Send absolute coordinates...
M83                                 	; ...but relative extruder moves

; Axis and motor configuration
M569 P0 S0				; Drive 0 goes forwards (x)
M569 P1 S1				; Drive 1 goes forwards (Y)
M569 P2 S1				; Drive 2 goes forwards (z)
M569 P3 S0				; Drive 3 goes forwards (e1)
M569 P4 S1				; Drive 4 goes forwards (E2)

; microstepping and homing switch config
M350 X16 Y16 Z16 E16 I1             ; set 16x microstepping with interpolation


M574 X1 S1 P"!xstop"   ; X min active high endstop switch
M574 Y1 S1 P"!ystop"   ; Y min active high endstop switch
M574 Z1 S1 P"zstop"   ; Z min active high endstop switch


; Motor current and acceleration
M906 X1000 Y1200 Z1200 E1200 I30		; Set motor currents (mA) and increase idle current to 60%
M84 S60 ; Set idle timeout

M201 X3000 Y3000 Z15 E3600		; Accelerations (mm/s^2) 
M203 X6000 Y6000 Z100 E1200		; feedrate  (mm/min)
M566 X1800 Y1800 Z180 E300		; Maximum instant speed changes mm/minute
M210 X5000 Y5000 Z60  			; set hming feedrate

; steps per mm
M92 X79.01 Y76.04 Z3298.92  ; Set axis steps/mm
M92 E415:415                          ; set extruder 0 and 1 steps/mm



; Thermistors
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.06e-8 ; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
M950 F0 C"fan0"  ; Fan 0
M140 H0 ; the bed heater is heater 0


M143 H1 S270 ; Set maximum heater temperature to 270C
M143 H0 S115 ; Set maximum heater temperature to 270C



; Tool definitions
M563 P0 D0 H1                       	; Define tool 0 old
M571 P"e0heat *" S1.0
G10 P0 S0 R0                        	; Set tool 0 operating and standby temperatures



; Z probe and compensation definition
M558 P1 C"^zprobe.in"  X0 Y0 Z1 H5 F500 T3000    ; smart IR Z probe, used for homing Z axis only, dive height 3mm, probe speed 200mm/min, travel speed 5000mm/min
G31 P500 X15 Y3 Z0.40        ; set threshold and offsets (we were at 0.50 BEFORE ADJUSTMENT)

;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0                   	; Axis compensation here


M206 X0 Y0 Z0
M208 X0 Y0 Z0 S1 				; set minimum Z
; max travel and origin
M208 X215 Y310 Z200 

;
T0					; select first hot end

M570 H1 P20 T30 

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

bed

G28 X0 Y0     ; Home All
G28 Z0        ; Home All
M561                         ; clear any existing bed transform
M557 X20:170 Y20:270 P2:2
M376 H3   ;taper off compensation after 3mm
G29

G1 X10 Y10 F5000               ; move the head to the corner (optional)

All,
I am facing an issue. I have adjusted my bed with a caliper and some jig and it appears to be level from left to right. I use a Mini differential IR sensor.
I have this build surface stick on a glass
[https://www.amazon.co.uk/gp/product/B07JMT8C9R/ref=ppx_yo_dt_b_asin_title_o04_s02?ie=UTF8&psc=1](link url)

When I run a G32, my bed look to have the center well above the left and right.
I created a macro that measure left and right and that gives me the left and right coordinates

G28                         ; home
G30 P0 X20 Y150 H0 Z-99999    ; probe near a leadscrew
G30 P1 X165 Y150 H0 Z-99999 S-1 ; probe near a leadscrew
M84

G28                         ; home
G30 P0 X20 Y150 H0 Z-99999    ; probe near a leadscrew
G30 P1 X165 Y150 H0 Z-99999 S-1 ; probe near a leadscrew
M84

This gives me

12/16/2020, 7:05:05 PM	M98 P"0:/macros/LEADSCREW"
G32 bed probe heights: -0.193 -0.174, mean -0.183, deviation from mean 0.010
12/16/2020, 7:01:26 PM	M999
G32 bed probe heights: -0.258 -0.233, mean -0.246, deviation from mean 0.013

The heat map looks as follow

RepRapFirmware height map file v2, min error -0.371, max error 0.133, mean -0.155, deviation 0.220
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
20.00,170.00,20.00,270.00,-1.00,150.00,250.00,2,2
 -0.371, -0.366
  0.133, -0.017

I can't manage to tweak it. Even, if I manage to get something better, it will fail in next 30 minutes with no print.

Antoine

@dc42 said in duplicate files in macro and setting:

iap4e

1. This solves the issue, I now have

Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.0 or 1.01
Firmware Version: 2.02RC6(RTOS) (2018-12-15b2)
WiFi Server Version: 1.21
Web Interface Version: 1.22.5

2. This is solved
3. Ok, so that's not an issue
4. This is solved

Thanks!!

Antoine

All,
I upgraded my DUET WIFI to latest firmware (DUET WIFI BATCH 3).
I now face 4 issues

1. the version is still showing as 1.21 (see below)
2. the files in MACRO, SETTING, and PLA are duplicated like if I was now able to call all the history
3. the web browser complains of a 404 error
   dwc.js:2 GET http://p3steel.local/rr_download?name=0:/sys/oem.json 404 (file not found)
4. diagnostic message requires to disconnect and reconnect to appear

See diagnostic below

=== Diagnostics ===
Used output buffers: 4 of 32 (14 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4S4-6J1DG-3S46N-TPHRY
Static ram used: 16152
Dynamic ram used: 100440
Recycled dynamic ram: 2192
Stack ram used: 1224 current, 4448 maximum
Never used ram: 7840
Last reset 00:01:04 ago, cause: software
Last software reset at 2018-12-16 22:53, reason: User, spinning module GCodes, available RAM 7888 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 28.9, current 29.7, max 29.9
Supply voltage: min 13.0, current 13.1, max 13.3, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2018-12-16 23:10:36
Slowest main loop (seconds): 0.013969; fastest: 0.000046
=== Move ===
MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21
  WiFi MAC address 60:01:94:09:bc:4e
  WiFi Vcc 3.44, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 15216
  WiFi IP address 10.0.0.18
  WiFi signal strength -58dBm, reconnections 0, sleep mode modem
  Socket states: 0 2 0 0 0 0 0 0
  === Expansion ===
  === Diagnostics ===
  Used output buffers: 13 of 32 (24 max)
  === Platform ===
  RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21 running on Duet WiFi 1.0 or 1.01
  Board ID: 08DAM-999TL-MQ4S4-6J1DG-3S46N-TPHRY
  Static ram used: 16152
  Dynamic ram used: 100440
  Recycled dynamic ram: 2192
  Stack ram used: 1224 current, 4448 maximum
  Never used ram: 7840
  Last reset 00:01:27 ago, cause: software
  Last software reset at 2018-12-16 22:53, reason: User, spinning module GCodes, available RAM 7888 bytes (slot 3)
  Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
  Error status: 0
  Free file entries: 10
  SD card 0 detected, interface speed: 20.0MBytes/sec
  SD card longest block write time: 0.0ms
  MCU temperature: min 29.2, current 29.5, max 29.7
  Supply voltage: min 13.1, current 13.1, max 13.2, under voltage events: 0, over voltage events: 0
  Driver 0: standstill, SG min/max not available
  Driver 1: standstill, SG min/max not available
  Driver 2: standstill, SG min/max not available
  Driver 3: standstill, SG min/max not available
  Driver 4: standstill, SG min/max not available
  Date/time: 2018-12-16 23:10:59
  Slowest main loop (seconds): 0.180053; fastest: 0.000112
  === Move ===
  MaxReps: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
  Scheduled moves: 0, completed moves: 0
  Bed compensation in use: none
  Bed probe heights: 0.000 0.000 0.000 0.000 0.000
  === Heat ===
  Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
  Heater 1 is on, I-accum = 0.0
  === GCodes ===
  Segments left: 0
  Stack records: 2 allocated, 0 in use
  Movement lock held by null
  http is idle in state(s) 0
  telnet is idle in state(s) 0
  file is idle in state(s) 0
  serial is idle in state(s) 0
  aux is idle in state(s) 0
  daemon is idle in state(s) 0
  queue is idle in state(s) 0
  autopause is idle in state(s) 0
  Code queue is empty.
  === Network ===
  Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
  HTTP sessions: 1 of 8
• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21
  WiFi MAC address 60:01:94:09:bc:4e
  WiFi Vcc 3.44, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 16680
  WiFi IP address 10.0.0.18
  WiFi signal strength -57dBm, reconnections 0, sleep mode modem
  Socket states: 4 2 0 0 0 0 0 0
  === Expansion ===

Thanks
I have ordered some terminal block which should come soon.
Antoine

Hello
Thanks
I will change the connector.
How can I check that nothing else is burnt?
As said the voltage was showing 0.

Antoine

can you see the picture now?
Antoine

All,
I think I have burnt my duet.
Here is a photo

or at that link
https://photos.app.goo.gl/DrQnB4S7q6YiejsH3

This happens after the printer heated as normal tonight.
I have checked and the Voltage is always 0V now.

I will anyway need to get a new connector terminal.

Does anyone know how to troubleshoot if I had fried the electronics?
Antoine

Thanks a million! that works

Thanks,
Is there a user guide on G32 and M671?
I basically get
G32
12 points probed, mean error 0.002, deviation 0.144
Height map saved to file heightmap.csv

Antoine

Thanks
So I should really only use M671 when I want to do a leadscrew calibration or a bed adjustment. In such case, how do I start the process, is that a G32?
Antoine

All,
I just upgraded to latest firmware and when I try to do 4 points bed probes, I am getting
Error: Number of calibration factors (4) not equal to number of leadscrews (2)

The commands I sent are

[[language]]
; BED PROBE SIMPLE
M561
G28 X0 Y0 Z0
G30 P0 X30 Y30 F100 Z-99999       ; define 4 points in a clockwise direction around the bed, starting near (0,0)
G30 P1 X30 Y270 F1500 Z-99999
G30 P2 X200 Y270 F1500 Z-99999
G30 P3 X200 Y30 F1500 Z-99999 S0

M84

My config is as follow, I am having since quite a while and there may be some old stuffs that are now causing issues.
I am especially wondering about the M671 but there may be something else.

[[language]]

; Communication and general
M111 S0                             	; Debug off
M550 pp3steel		; Machine name and Netbios name (can be anything you like)
;M551 Ppreprap                        	; Machine password (used for FTP)
;*** If you have more than one Duet on your network, they must all have different MAC addresses, so change the last digits
; M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED 	; MAC Address
;*** Wifi Networking
M552 S1				; Enable WiFi

; misc settings
M555 P2                           	; Set output to look like Marlin
M575 P1 B57600 S1			; Comms parameters for PanelDue

; setting for all axis
G21                                 	; Work in millimeters
G90                                	; Send absolute coordinates...
M83                                 	; ...but relative extruder moves

; Axis and motor configuration
M569 P0 S0				; Drive 0 goes forwards (x)
M569 P1 S1				; Drive 1 goes forwards (Y)
M569 P2 S1				; Drive 2 goes forwards (z)
M569 P3 S0				; Drive 3 goes forwards (e1)
M569 P4 S1				; Drive 4 goes forwards (E2)

; microstepping and homing switch config
M350 X16 Y16 Z16 E16 I1             ; set 16x microstepping with interpolation

M574 X1 S0		    ; set homing switch configuration (X homing switch only, at low end, active high)
M574 Y1 S0		    ; set homing switch configuration (Y homing switch only, at low end, active high)
M574 Z0 S1		    ; set homing switch configuration (z homing switch only, at low end, active high)

; Motor current and acceleration
M906 X1000 Y1100 Z1000 E1100 I60		; Set motor currents (mA) and increase idle current to 60%
M84 S60 ; Set idle timeout

M201 X600 Y600 Z10 E600		; Accelerations (mm/s^2) 
M203 X5000 Y5000 Z100 E9000		; Maximum speeds (mm/min)

M566 X1200 Y1200 Z30 E200		; Maximum instant speed changes mm/minute
M210 X6000 Y6000 Z10  			; set hming feedrate

; steps per mm
M92 X80 Y80 Z4000  ; Set axis steps/mm
M92 E492.45:492.45                          ; set extruder 0 and 1 steps/mm

; max travel and origin
M208 X210 Y305 Z200 

; setting for all axis
G21                                 	; Work in millimeters
G90                                	; Send absolute coordinates...
M83                                 	; ...but relative extruder moves

; Thermistors

M305 P0 R4700 T100000 B4388   ; set bed thermistor parameters
M305 P1 R4700 T100000 B4388   ; set E0 thermistor parameters
M307 H1 A474.7 C114.3 D5.5 B0; PID settings for extruder 0
M143 H1 S270 ; Set maximum heater temperature to 270C
M307 H0 D20

; Fans
M106 P1 H-1 				; disable thermostatic mode for fan 1

; Tool definitions
M563 P0 D0 H1                       	; Define tool 0
G10 P0 S0 R0                        	; Set tool 0 operating and standby temperatures

; Z probe and compensation definition
M558 P1 X0 Y0 Z1 H3 F200 T3000    ; smart IR Z probe, used for homing Z axis only, dive height 3mm, probe speed 200mm/min, travel speed 5000mm/min
G31 P500 X10 Y24 Z1.90        ; set threshold and offsets

;*** If you are using axis compensation, put the figures in the following command
M556 S78 X0 Y0 Z0                   	; Axis compensation here

M208 X0 Y0 Z0 S1 				; set minimum Z
;
T0					; select first hot end

M671 X--60:270 Y45:45
; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

Hello
I had to upgrade to 1.19beta and it works.
Antoine

All,
I moved house and now the router is not in my office room.
The DUET WIFI refuse to connect to it except if I am using an old DD-WRT that I setup as repeater bridge.
Problem, this old device is extremly slow, and the computer in the office will now connect to it.

Is there anyway to change the network setting in the DUET so that it connects to a different network?

Antoine

Hello,
I am using F300 which is I think 5mm/sec.

Antoine

@dc42:

What speed are you running the extruder at when you do the calibration? Is the extruder drive connected to the hot end, or not?

hello,
I have tried 5, 10 and 15 i n UI.
Interesting enough, the issue doesn't seem to be present when using the GCODE CONSOLE.
Antoine