@dc42 turns out I spoke too soon... The printer crashed again midway into a print. I made changes to the way I ran the wire and am testing again. Here is the log:
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.5 (2022-11-30 19:35:23) running on Duet 3 MB6HC v1.01 (standalone mode)
Board ID: 08DJM-956BA-NA3TJ-6JTD8-3SJ6J-1UA2U
Used output buffers: 3 of 40 (22 max)
=== RTOS ===
Static ram: 152760
Dynamic ram: 97584 of which 76 recycled
Never used RAM 100252, free system stack 204 words
Tasks: NETWORK(ready,151.5%,230) ETHERNET(notifyWait,0.3%,401) HEAT(notifyWait,0.1%,322) Move(notifyWait,0.0%,351) CanReceiv(notifyWait,0.0%,944) CanSender(notifyWait,0.0%,336) CanClock(delaying,0.1%,333) TMC(notifyWait,41.6%,91) MAIN(running,325.0%,925) IDLE(ready,0.0%,30), total 518.5%
Owned mutexes:
=== Platform ===
Last reset 01:58:14 ago, cause: software
Last software reset at 2023-04-05 14:10, reason: MemoryProtectionFault mmarValid daccViol, Platform spinning, available RAM 95836, slot 2
Software reset code 0x4160 HFSR 0x00000000 CFSR 0x00000082 ICSR 0x00427804 BFAR 0x61c30f6c SP 0x2041b608 Task MAIN Freestk 1738 ok
Stack: 00000000 00000000 9e3cf497 00000000 0000036c 00476159 00474eae 21000000 00000000 204194f4 20419a84 8100001b 00493838 2042474c 00000000 00000000 00000000 00000000 20430238 00000000 20430b84 00000000 00000189 00476159 20430b3c 00474ebf 07ef5235
Error status: 0x00
Step timer max interval 130
MCU temperature: min 36.6, current 37.3, max 40.0
Supply voltage: min 23.8, current 23.8, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, mspos 8, reads 15072, writes 15 timeouts 0
Driver 1: standstill, SG min 0, mspos 568, reads 15073, writes 15 timeouts 0
Driver 2: standstill, SG min 0, mspos 184, reads 15073, writes 15 timeouts 0
Driver 3: standstill, SG min 0, mspos 696, reads 15073, writes 15 timeouts 0
Driver 4: standstill, SG min 0, mspos 616, reads 15073, writes 15 timeouts 0
Driver 5: standstill, SG min 0, mspos 344, reads 15073, writes 15 timeouts 0
Date/time: 2023-04-05 16:08:30
Slowest loop: 4.58ms; fastest: 0.06ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0: pos -6.54, errs: frame 5 parity 0 ovrun 0 pol 0 ovdue 0
=== CAN ===
Messages queued 63853, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 50 (min 50), ts 35475/0/0
Tx timeouts 0,0,35474,0,0,28377 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 2.77ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
= Ethernet =
State: active
Error counts: 0 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== Multicast handler ===
Responder is inactive, messages received 0, responses 0
