Delta Cable management
-
Got link for the retractable ring? Was just thinking how cool it would be to have something like that but with adjustable pull.
-
All my end stop cabling runs up each tower on the inside (the center of the extrusion) so its totally invisible, even at the top I cut a small section out of the back of the slot to allow the cable to turn and come back down to the stop switch, cabling to the effector and extruder run up the rear tower in the slot on the back. I'm using a slightly modified version of DC42's cable clip.
The cable then passes over the top of the extruder and is spiral wrapped to the bowden tube down to the effector.
-
@dadiy said in Delta Cable management:
All my end stop cabling runs up each tower on the inside (the center of the extrusion) so its totally invisible, even at the top I cut a small section out of the back of the slot to allow the cable to turn and come back down to the stop switch, cabling to the effector and extruder run up the rear tower in the slot on the back. I'm using a slightly modified version of DC42's cable clip.
The cable then passes over the top of the extruder and is spiral wrapped to the bowden tube down to the effector.
Yeah that sounds pretty standard. In my case my towers are 1.5 meters tall so you basically have 1.5 meters of cable that have to extend and then be able to home without getting in the way.
-
@mysta said in Delta Cable management:
@dadiy said in Delta Cable management:
Yeah that sounds pretty standard. In my case my towers are 1.5 meters tall so you basically have 1.5 meters of cable that have to extend and then be able to home without getting in the way.
Just for fun, how about some pics of your 1.5 M tall printer? In a different thread, if you prefer...
-
@danal Sure! It's relevant in this thread - I'll grab some pics when I get home. Cables and stuff are still 'temporary'.
-
@mysta Yes, My towers are just over 1.7 meters tall so i just made up some cables before inserting the towers into the base.
For anyone interested there are a few build photos of my printer here - https://imgur.com/gallery/O1jtC I do need to add some of the finished printer but these give an idea of size and include the custom table I built which suspends the filament under the table on a lazy suzanne.
-
Here’s two pics of it finished showing the cables etc.
-
@dadiy So your cables will reach the top like that without strain?
-
Yes. It’s been running like that for 6 months without issue. My biggest problem was the extruder. I bought a Titan extruder but it didn’t have the grip for my tube. I’m now on the Bondtech and never had a problem.
-
@mysta said in Delta Cable management:
Got link for the retractable ring? Was just thinking how cool it would be to have something like that but with adjustable pull.
I had a dig around for it but I can't find that particular unit for sale anymore. Its got a metal cable inside and is fairly sturdy, they're all fairly similar.
-
Here's a simple cell phone video of the "Stretch Magic" at work:
-
@danal said in Delta Cable management:
Here's a simple cell phone video of the "Stretch Magic" at work:
What bed heater is that?
-
@mysta said in Delta Cable management:
What bed heater is that?
Custom made by Keenovo. 590mm dia (glass is 604), 1400W on 120V (US standard), with built in 150C thermal protector. $240 USD, shipped.
Took some extra time because I ordered it JUST before China holiday.
The glass is a tabletop advertised as 24" by 3/8" (604mm by 9.5mm, roughly) on Amazon in the US. About $40 us shipped. I've been happy with it, although I'd note it is not very round. This makes no practical difference, so far, just a little bit of tweaking any time you remove it and replace it in the clips. It is reasonably flat, reflections of distant items on the surface show no noticeable distortion.
So the total bed was about $280 US. Considering I had ideas in my head ranging from cast aluminum plate to who knows what, that were going to be a lot more money, I'm very happy to report that the simple heater stuck to the glass (the heater came with a sticky layer) works GREAT!! Very happy with it. And, if I every damage the glass, it is the cheapest part.