2 NEW DUET 2 WIFI's W/EXTERNAL ANTENNA WILL NOT CONNECT

Phaedrux

I'm a bit confused now about what state you're currently in.

Have you been following this guide?
https://docs.duet3d.com/en/How_to_guides/Getting_connected/Getting_connected_to_your_Duet

If you are replacing a board, do you already have an existing configuration from the old board?

GBusy24

@Phaedrux yes the SD cards seems to have all of the data still intact from the two boards I'm replacing

GBusy24

@Phaedrux so I guess maybe I could just switch out the cards right?

Phaedrux

@GBusy24 said in 2 NEW DUET 2 WIFI's W/EXTERNAL ANTENNA WILL NOT CONNECT:

@Phaedrux so I guess maybe I could just switch out the cards right?

For the most part yes as long as the firmware version was at least close in version.

The wifi SSID and password need to be re-added because they are stored on the module, so you'd still want to use the getting connected guide I linked above.

GBusy24

@Phaedrux Understood and thanks.

GBusy24

@Phaedrux, I've moved over to the second new board and inserted the SD card from the old board just for a fresh start. Here's the YAT terminal stuff to show what I've done. At this point, I've got myself confused. Look this over and let me know what you think. Thanks.Phaedrux File.txt I will add that the getting started article confuses me as far as the M552 commands. In step 4, it says to send M552 S1 to stop the wifi and then later after explaining setting the network with M587, it says send M552 S1 to connect the wifi. The green wifi light never flashes or stays lit.

GBusy24

@Phaedrux Here's the config.g from the old SD card that I inserted to the new board. Thought you'd want to see it too.config.g

GBusy24

@Phaedrux 111.txt

Phaedrux

Did you follow this section to add your SSID and password to get connected again?

https://docs.duet3d.com/en/How_to_guides/Getting_connected/Getting_connected_to_your_Duet#h-5-connect-duet-to-network

GBusy24

@Phaedrux yes

GBusy24

@Phaedrux one of my posts to you last night seems to be deleted or at least it's grayed out and I don't know if you saw it so I'm going to reshare the link I had in the post. Here it is...M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.5.3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2024-09-18 11:25:32
ok
M587
Remembered networks:
Gregs WIFI IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
TNCAPF318D9 IP=192.168.1.14 GW=0.0.0.0 NM=0.0.0.0
ok
M552 S0
ok
M552 S1
ok
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.5.3 (2024-09-18 11:25:32) running on Duet WiFi 1.02 or later
Board ID: 0JD6M-99APT-NU4SN-6J9F4-3SD6K-14PTL
Used output buffers: 1 of 26 (1 max)
=== RTOS ===
Static ram: 23376
Dynamic ram: 72792 of which 0 recycled
Never used RAM 17308, free system stack 194 words
Tasks: NETWORK(1,ready,7.0%,339) HEAT(3,nWait 5,0.0%,328) Move(4,nWait 5,0.0%,359) MAIN(1,running,92.9%,501) IDLE(0,ready,0.1%,29), total 100.0%
Owned mutexes: USB(MAIN)
=== Platform ===
Last reset 00:20:56 ago, cause: power up
Last software reset details not available
Error status: 0x00
MCU temperature: min 25.7, current 30.8, max 31.9
Supply voltage: min 0.2, current 1.4, max 1.8, under voltage events: 0, over voltage events: 0, power good: no
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok, SG min n/a
Driver 1: ok, SG min n/a
Driver 2: ok, SG min n/a
Driver 3: ok, SG min n/a
Driver 4: ok, SG min n/a
Driver 5:
Driver 6:
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 1970-01-01 00:00:00
Cache data hit count 4294967295
Slowest loop: 99.91ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.2ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "M122" in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Q0 segments left 0
Code queue 0 is empty
=== Network ===
Slowest loop: 0.73ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 0 of 8
=== WiFi ===
Interface state: changingMode
Module is idle
Failed messages: pending 0, notrdy 0, noresp 0
Failed to get WiFi status
Socket states: 0 0 0 0 0 0 0 0
ok
Error: failed to retrieve WiFi status message: bad reply format version
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle
Error: WiFi module reported: no known networks found
WiFi module is idle

jay_s_uk

@GBusy24 can you post a photo of the board?

GBusy24

@jay_s_uk unfortunately, I'm at work right now

GBusy24

@jay_s_uk may I ask what you would be looking for on the board and maybe I can help her memory. It is one of the newer boards with the external Wi-Fi antenna

jay_s_uk

@GBusy24 just checking that everything looks ok. as the wifi module appears to be working, the antenna is either not connected correctly or is not functioning.
I've seen cases of antennas not working correctly

GBusy24

@jay_s_uk I'm really confident that the antenna is connected correctly but I will mention that it is not mounted it is just laying near the board

jay_s_uk

@GBusy24 just laying around is fine. In that case, I would suggest changing the antenna

GBusy24

@jay_s_uk okay, but who will sell me just the antenna? I have two because I have two new boards. Maybe I should try the other antenna off of The Other Board

GBusy24

@jay_s_uk I will say that when working with the other board the green light on the Wi-Fi module would blink constantly where I get nothing out of this current board I'm working with

jay_s_uk

@GBusy24 yea, try the other one.
you can get antennas off amazon easily enough. search for a U.FL Antenna for wifi