Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    npn 5v fly rrf e3

    Scheduled Pinned Locked Moved
    STM
    3
    35
    1.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • npm1undefined
      npm1 @npm1
      last edited by

      shall i update the firmware

      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

      npm1undefined 1 Reply Last reply Reply Quote 0
      • npm1undefined
        npm1 @npm1
        last edited by

        Electronics
        Diagnostics
        Board: fly_E3 (STMWiFi)
        Firmware: RepRapFirmware for STM32F4 based Boards 3.3RC2+1_1 (2021-05-13)
        Duet WiFi Server Version: 1.26-01S-D

        Note: You can install updates on the System page.

        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

        npm1undefined gloomyandyundefined 2 Replies Last reply Reply Quote 0
        • npm1undefined
          npm1 @npm1
          last edited by

          will marlin be easier

          Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

          1 Reply Last reply Reply Quote 0
          • gloomyandyundefined
            gloomyandy @npm1
            last edited by gloomyandy

            @npm1 Can you turn off your board, disconnect the probe and plug in one of the other endstop switches (x or y) into the zstop socket. Then run the two tests again once without pressing the endstop switch, then again with the endstop switch pressed. Run this test with the Z driver still removed.

            npm1undefined 1 Reply Last reply Reply Quote 0
            • npm1undefined
              npm1 @gloomyandy
              last edited by

              @gloomyandy endstop works with zero issues with everything triggered correctly

              M119

              Endstops - X: at min stop, Y: at min stop, Z: at min stop, Z probe: at min stop
              2/25/2022, 9:38:20 PM g31
              Z probe 0: current reading 0, threshold 500, trigger height 2.500, offsets X0.0 Y0.0
              2/25/2022, 9:38:10 PM m119
              Endstops - X: at min stop, Y: at min stop, Z: not stopped, Z probe: not stopped

              Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

              npm1undefined 1 Reply Last reply Reply Quote 0
              • npm1undefined
                npm1 @npm1
                last edited by

                @gloomyandy the only thing i can think of is to switch the cables on the zstop cables around

                Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                gloomyandyundefined 1 Reply Last reply Reply Quote 0
                • gloomyandyundefined
                  gloomyandy @npm1
                  last edited by

                  @npm1 @npm1 In which case I would be looking very closely at that probe. Are you sure you have correctly identified the various wires? See: https://forum.duet3d.com/topic/25906/inductive-sensor-npn-no-not-working?_=1645824856161 (thanks to Jay for digging that one out).

                  npm1undefined 1 Reply Last reply Reply Quote 0
                  • npm1undefined
                    npm1 @gloomyandy
                    last edited by

                    @gloomyandy i knoq that the 5v cable is correctly connected ill switch the cables around and confirm to you shortly

                    Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                    npm1undefined 1 Reply Last reply Reply Quote 0
                    • npm1undefined
                      npm1 @npm1
                      last edited by

                      I'm just gonna call it a day, may use an optical setup it with one of those allen keys

                      Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                      npm1undefined 1 Reply Last reply Reply Quote 0
                      • npm1undefined
                        npm1 @npm1
                        last edited by

                        thanks for your efforts

                        Ender 5 pro(LGXextruderddewith e3d revo rapid changer) with fly rrf e3 and a standard prusa mk3, both siting air-tight in a ikea kitchen cabinet.

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Unless otherwise noted, all forum content is licensed under CC-BY-SA