DWC 3.1.1

[Phaedrux]

M303 H1 S

You need to set a temperature after the S

M303 H1 S200

[luca Massimiliano]

AVEVO CAPITO HE S NON IMPOSTATO ANDAVA ALLA MASSIMA TEMPERATURA .GRAZIE PROVO SUBITO

[luca Massimiliano]

This post is deleted!

[luca Massimiliano]

@Phaedrux PERFETTO
GRAZIE

[luca Massimiliano]

NON HO CAPITO . HO FATTO G 29 LA MACCHINA HA LAVORATO MA NIENTE GRAFIGO RAPPRESENTATO COME SI VEDE. UNA VOLTA HA FATTO GRAFICO CON UN G 29 POI NON PIU'

gives me this error Error: Bad command: Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT + 0100 (Central European Standard Time)

It sounds like you are missing a ; to commend out that line?

NON COMPRENDO SCUSA

[luca Massimiliano]

[luca Massimiliano]

MI HA MANDATO QUI NON SO SE HA IMPORTANA PENSO RIGUARDI LO SPESSORE E IL MATERIALE, DEVO CREARE UN FILE

[Phaedrux]

Create a folder on your SD card called menu and another called filaments

Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT + 0100 (Central European Standard Time)

Check your config files for that line. Some where there is a file that has that line and it's missing a ; at the start to mark it as a comment.

[luca Massimiliano]

; generated by RepRapFirmware Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT+0100 (Ora standard dell’Europa centrale)

; IN GONFIG.G OK

Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT + 0100 (Central European Standard Time)

Check your config files for that line. Some where there is a file that has that line and it's missing a ; at the start to mark it as a comment.

[Phaedrux]

What are you doing when that error message shows up?

[luca Massimiliano]

HO FATTO MENU FILAMENT IN SD CARD

[luca Massimiliano]

ECCO

[luca Massimiliano]

SE TOCCO PIANO-SONDATO .CSV SI BLOCCA TUUO.

[luca Massimiliano]

This post is deleted!

[luca Massimiliano]

DA L ERRORE QUANDO ARRIVA SUL PIATTO ED ESTRAE LA SONDA HO UN BBLTouch

[Phaedrux]

Please post all your config files. config.g homeall.g homex.g homey.g homez.g homedelta.g bed.g deployprobe.g retractprobe.g

[luca Massimiliano]

@luca-Massimiliano

[Phaedrux]

Do you have a file called mesh.g in the system folder?

[luca Massimiliano]

@Phaedrux said in DWC 3.1.1:

no non ho la mesh.g G29 Esegui il file sys / mesh.g, o se quel file non viene trovato, esegui G29 S0 ho fatto cosi errore:
G29 S0
Error: Bad command: Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT+0100 (Ora standard dell’Europa centrale)...

ora confronto ifail detti da te config files. config.g homeall.g homex.g homey.g homez.g homedelta.g bed.g deployprobe.g retractprobe.g con i vecchi senza problema se non risolvo li posto ,

[luca Massimiliano]

@luca-Massimiliano said in DWC 3.1.1:

Error: Bad command: Configuration Tool v3.2.3 on Sun Mar 14 2021 01:38:34 GMT+0100 (Ora standard dell’Europa centrale)...
RISOLTO
COME DICEVI TE NO ERA NASCOSTO NEL FILE DELOYPROBLE.G