Endstops not working during homeing but light up on board

resh

Sorry, thought it was in code above. Duet 2 WiFi on latest firmware.

fcwilt

@resh said in Endstops not working during homeing but light up on board:

Yes, I can press each endstop and verify it by LED on the duet. When I home all everything Moves in correct direction and tries to continue moving before I hit stop. If I choose an individual X or X the Z bed will move slightly, like the code suggests, but then nothing else seems to happen.

Did you verify that each axis is actually pressing the endstop sensor the way you are when you do it manually?

Frederick

User3D

@resh can you do following:
home any one axis. Manually light up respective endstop and see if axis actually stops immediately (Don't wait for it to reach to endstop).

If it doesn't stop then manually light up endstops of other axes and see if it stops .If so you have configured them wrongly. But if it doesn't stop at all then there might be wiring issue I guess.

resh

I appreciate the responses. The axis are physically touching the switches correctly. I've done a bit more reading on here and determined my endstops are makerbot. I verified wiring of those and setup on config. I'm taking it one axis at a time for now. When I home the X, the Z moves down and X moves about 5-10mm towards the endstop and just stops. It doesn't go all the way to it and trigger. It's definitely not doing the G code for call to home X.

In reprap config generator what is X minimum and Maximum? I know my bed size and can calculate travel. I feel like I've done this correctly if it homes in the correct direction? Also, what is Endstop location, Low or High end? New config below. Thank you for your patience.

called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Feb 26 2021 10:46:02 GMT-0500 (Eastern Standard Time)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X315 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X-5 F6000 ; go back a few mm
G1 H1 X315 F360 ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000 ; lower Z again
G90 ; absolute positioning

General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X310 Y310 Z180 S0 ; set axis maxima

; Endstops
M574 X2 S1 P"!xstop" ; configure active-high endstop for high end on X via pin !xstop
M574 Y2 S1 P"!ystop" ; configure active-high endstop for high end on Y via pin !ystop
M574 Z2 S2 ; configure Z-probe endstop for high end on Z

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid

Veti

@resh said in Endstops not working during homeing but light up on board:

Duet 2 WiFi on latest firmware.

are you sure? please post the output of m115

resh

@Veti Maybe I'm reading this wrong?

IRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.2.2 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2021-02-11

Veti

no just making sure. some people just upload 3.2 without going over 3.0 and assume the firmware update took, when in fact it failed.

Veti

can you post a picture of the wiring on the endstop and on the board?

fcwilt

@resh said in Endstops not working during homeing but light up on board:

I appreciate the responses. The axis are physically touching the switches correctly. I've done a bit more reading on here and determined my endstops are makerbot. I verified wiring of those and setup on config. I'm taking it one axis at a time for now. When I home the X, the Z moves down and X moves about 5-10mm towards the endstop and just stops. It doesn't go all the way to it and trigger. It's definitely not doing the G code for call to home X.

If you look at the homing code for the X axis there are 3 X axis moves:

G1 H1 X315 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X-5 F6000 ; go back a few mm
G1 H1 X315 F360 ; move slowly to X axis endstop once more (second pass)

If the endstop was already triggered for some reason the two G1 H1 moves would not happen because they stop when the endstop triggers. You would only see the G1 H2 move but that should be away from the endstop.

If you are only seeing the G1 H2 move but it is towards the endstop you have two problems:

the firmware is seeing the endstops as triggered at the start of the homing process
the movement is in the wrong direction

Try changing...
M574 X2 S1 P"xstop"
...to...
M574 X2 S1 P"!xstop"

In reprap config generator what is X minimum and Maximum? I know my bed size and can calculate travel. I feel like I've done this correctly if it homes in the correct direction? Also, what is Endstop location, Low or High end? New config below. Thank you for your patience.

Lets assume the printable area of the bed is 200 x 200. In the simplest case X min = 0 and X max = 200. You can also chose to have X = 0 be at the center of the axis in which case X min = -100 and X max = +100.

For an endstop the low end is at or near the X min end, the high end is at/near X max.

Frederick

resh

my config was already M574 X2 S1 P"!xstop. I took out the ! and tried it but it gave the exact same results. There are no leads cut on the endstops and they test correctly by manually pushing them. I have some more of these endstops I can throw on or I have no problem buying different ones if you guys think that will correct the issue.

Veti

do the endstops work with 3.3v? they are designed for 5V

resh

Adding to this. The axis seem to be backwards as noted. After I home I can jog but -X on PanelDue goes right, X goes left. I can also only go as far left as the origin of the head was when I originally homed if that makes any sense.

resh

There are other threads with these endstops so I'm only assuming they work.

I sent M119 and got 'Not Stopped' for all. Then I manually pressed X, sent M119 and got 'At max stop', same for Y. I guess this means it's functioning correctly? Something in the config then?

Veti

@resh said in Endstops not working during homeing but light up on board:

Then I manually pressed X, sent M119 and got 'At max stop', same for Y. I guess this means it's functioning correctly?

that means you swapped x and y cables just swap the connectors on the board.

resh

@Veti I didn't explain that well. They reported back correctly. I held X and it reported 'at max stop' and Y,Z said 'not stopped'. When I did Y it said 'at max stop' and X,Z said 'not stopped'. Unless I'm missing something.

Also, why do I have a homedelta.g folder in my directory? I selected Cartesian during the reprap config.

Veti

you tested with your finger. can you test with the actual carriage if that also triggers the endstop?

resh

@Veti Yes, the carriage is physically touching the endstops correctly.

resh

Pressing 'home all' which I haven't done after re-config moves everything away from the limit switches. I have to stop it before it crashes but at least it moves more than just homeing one axis at a time.

Veti

do very first that your movement directions are correct.

set a position with G92 X50 Y50 and test with small directional movements

resh

@Veti Thanks for hanging with me here.

I input that code and jogged and X, Y are opposite. I'll press X-10 on the paneldue and it goes right, X10 and it goes left. Same with Y, it's backwards. Y-10 goes backwards, Y10 goes forwards.