Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware
-
@Hélder-Rocha said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
the message i get is "Enable to connect" .
can you post a picture of it?
-
Ok, firmware version is good. Wifi server should be good. And it says it is in access point mode with the correct IP. You can connect to the wifi, but when trying to reach 192.168.1.1 in your browser you get an error message in your browser saying "enable to connect"?
Have you tried these suggestions from earlier yet?
@Phaedrux said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
Try clearing your browser cache.
And if that doesn't work, I would check the /www folder on the SD card and replace the files there with a fresh copy of DWC.
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/DuetWebControl-SD.zip
What url are you trying to reach exactly?
-
M552 S2
ok
WiFi module is providing access point DuetCr10, IP address 192.168.1.1when this was working properly, i use to have this same message repeatedly. Now just shows one time!
-
@Phaedrux allready clean my cache and the problem remains. About the replacement of the 3.2, im going to do it now
-
@Hélder-Rocha said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
About the replacement of the 3.2, im going to do it now
Alright, replace the contents of /www with the contents of this zip file.
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/DuetWebControl-SD.zip
-
@Phaedrux didnt change the problem. When this was working ok, usualy i had to eject M552 S2 twice. Pist an error appear, but at the second time, usualy the message shows pepeatedly. Now, whem i send the comand, goes strait to the message saying the module is providing access point!
-
could it be an error from firefox?
-
Well you are running newer firmware on both the duet and the wifi module, so the behaviour may be a bit different looking than you're used to.
Can you post a screen shot or photo of what the firefox error message is saying?
control-shift-K will open the dev console in firefox which may show any errors.
-
cant uload the image!!!! gives me an error.... looks this day is a complete error.
-
-
wait...to small
-
-
Its trying to use HTTPS. Change the url to use only http
-
the same appens on chrome!
-
@Phaedrux said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
Its trying to use HTTPS. Change the url to use only http
Going to check how that is done...
-
Just change the url.
HTTP: instead of HTTPS:
-
@Phaedrux said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
Just change the url.
HTTP: instead of HTTPS:
it changes again to HTTPS...i erase the "s" but doesnt work
-
@Hélder-Rocha I don't know if that's a problem or just what it normally does when it can't reach the site.
Are you able to connect the duet to your home wifi?
-
even if i try the duettest.local... it changes to the https followed by the ip number
-
@Phaedrux said in Update CR-10+Duet wifi from 2.05.1 to 3.0 firmware:
@Hélder-Rocha I don't know if that's a problem or just what it normally does when it can't reach the site.
Are you able to connect the duet to your home wifi?
no... i am trying by the access point given by the board
