Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Artillery X1 Duet Maesto

    Scheduled Pinned Locked Moved
    General Discussion
    3
    8
    316
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • flopo76undefined
      flopo76
      last edited by

      Hello, i have an Artillery X1 with duet maestro RFF 3 firmware,when i try to heat up the nozzle the tool fan always start to 50%,even when i try to put it 100%,aftre the nozzle purged and the print start,the fan go to 50%.Need to increase manualy....

      My config file....

      ; Configuration file for Duet Maestro (firmware version 3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.1.4 on Thu Sep 10 2020 08:29:26 GMT+0200 (Ora legale dell’Europa centrale)

      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"Artillery X1" ; set printer name

      ; Network
      M552 P192.168.1.20 S1 ; enable network and set IP address
      M553 P255.255.255.0 ; set netmask
      M554 P192.168.1.1 ; set gateway
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S1 ; disable Telnet

      ; Drives
      M569 P0 S0 ; physical drive 0 x goes forwards
      M569 P1 S1 ; physical drive 1 y goes forwards
      M569 P2 S0 ; physical drive 2 z goes forwards
      M569 P3 S1 ; physical drive 3 e goes forwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X64 Y64 Z64 I1 ; configure microstepping without interpolation
      M350 E16 I1 ; configure microstepping with interpolation
      M92 X320.48 Y320.48 Z1619.35 E445.00 ; set steps per mm
      M566 X480.00 Y900.00 Z18 E420.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X12000.00 Y12000.00 Z2000.00 E12000.00 ; set maximum speeds (mm/min)
      M201 X2000.00 Y2000.00 Z350 E10000.00 ; set accelerations (mm/s^2)
      M906 X1100 Y1100 Z1100 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X300 Y300 Z400 S0 ; set axis maxima
      ;G31 X-28 Y33

      ; Endstops
      M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop
      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

      ; Z-Probe
      M950 S0 C"^zprobe.mod" ; create servo pin 0 for BLTouch
      M558 P9 C"^zprobe.in" H7 F600 T6000 ; set Z probe type to bltouch and the dive height + speeds
      G31 P500 X-28 Y-33 Z1.285 ; set Z probe trigger value, offset and trigger height
      M557 X1:240 Y10:260 P3:3 ; define mesh grid

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S0 H0:1 T50 ; set fan 0 value. Thermostatic control is turned on
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off
      M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
      M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off

      ; Tools
      M563 P0 D0 H1 F0:1 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings
      M575 P1 S1 B57600 ; enable support for PanelDue
      M501 ; load saved parameters from non-volatile memory
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
      M572 D0:1:2 S0.05

      ; Miscellaneous
      ;M575 P1 S1 B57600 ; enable support for PanelDue
      ;M501 ; load saved parameters from non-volatile memory
      ;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
      ;M572 D0:1:2 S0.05

      Phaedruxundefined 1 Reply Last reply Reply Quote 0
      • Vetiundefined
        Veti
        last edited by

        @flopo76 said in Artillery X1 Duet Maesto:

        M106 P0 S0 H0:1 T50 ; set fan 0 value. Thermostatic control is turned on

        i think this should be
        M106 P0 S1 H0:1 T50 ; set fan 0 value. Thermostatic control is turned on

        1 Reply Last reply Reply Quote 0
        • flopo76undefined
          flopo76
          last edited by

          Ok i will try...thanks.

          1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti
            last edited by

            @flopo76 said in Artillery X1 Duet Maesto:

            i try to heat up the nozzle the tool fan always start to 50%,even when i try to put it 100%,aftre the nozzle purged and the print start,the fan go to 50%.Need to increase manualy....

            btw the tool fan speed is controlled by the slicer.

            1 Reply Last reply Reply Quote 0
            • flopo76undefined
              flopo76
              last edited by

              Ok.S1 is active now,but when the print start the tool fan go to stop.This happend with all my printers. All with duet wifi or duet maestro. I use Cura for slicing.

              Example gcode with Cura:

              ;FLAVOR:RepRap
              ;TIME:8401
              ;Filament used: 10.0294m
              ;Layer height: 0.28
              ;MINX:90.864
              ;MINY:90.856
              ;MINZ:0.25
              ;MAXX:209.138
              ;MAXY:209.144
              ;MAXZ:10.89
              ;Generated with Cura_SteamEngine 4.8.0-beta
              T0
              M190 S85
              M104 S235
              M109 S235
              M82 ;absolute extrusion mode
              G28 ; home all axes
              M117 Purge extruder
              G92 E0 ; reset extruder
              G1 Z1.0 F3000 ; move z up little to prevent scratching of surface
              G1 X2 Y20 Z0.3 F5000.0 ; move to start-line position
              G1 X2 Y200.0 Z0.3 F1500.0 E15 ; draw 1st line
              G1 X2 Y200.0 Z0.4 F5000.0 ; move to side a little
              G1 X2 Y20 Z0.4 F1500.0 E30 ; draw 2nd line
              G92 E0 ; reset extruder
              G1 Z1.0 F3000 ; move z up little to prevent scratching of surface
              M83 ;relative extrusion mode
              G1 F1500 E-1
              ;LAYER_COUNT:39
              ;LAYER:0
              M107
              G0 F9000 X107.957 Y108.408 Z0.25
              ;TYPE:SKIRT
              G1 F1500 E1
              G1 F3600 X110.351 Y106.12 E0.13768
              G1 X110.519 Y105.968 E0.00942
              G1 X113.045 Y103.827 E0.13767
              G1 X113.223 Y103.686 E0.00944
              G1 X115.872 Y101.7 E0.13765
              G1 X116.058 Y101.569 E0.00946
              G1 X118.823 Y99.744 E0.13774
              G1 X119.016 Y99.624 E0.00945
              G1 X121.884 Y97.968 E0.13769

              Vetiundefined 1 Reply Last reply Reply Quote 0
              • flopo76undefined
                flopo76
                last edited by

                And why,when i want to power up the tool fan the print coller fan goes up?

                20201109_101039_1.gif

                1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti @flopo76
                  last edited by

                  @flopo76 said in Artillery X1 Duet Maesto:

                  M107

                  That means fan off.

                  1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @flopo76
                    last edited by Phaedrux

                    @flopo76 said in Artillery X1 Duet Maesto:

                    ; Fans
                    M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                    M106 P0 S0 H0:1 T50 ; set fan 0 value. Thermostatic control is turned on
                    M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                    M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off
                    M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
                    M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off
                    ; Tools
                    M563 P0 D0 H1 F0:1 ; define tool 0

                    Fan0 should be the part cooling fan and Fan1 should be the heatsink fan. You've got them backwards.

                    Try this instead with the part cooling fan connected to Fan0 and the heatsink fan connected to fan1.

                    ; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 T50 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H0:1 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0

                    Z-Bot CoreXY Build | Thingiverse Profile

                    1 Reply Last reply Reply Quote 0
                    • First post
                      Last post
                    Unless otherwise noted, all forum content is licensed under CC-BY-SA