Inconsistent results with optical encoder wheel filament sensor

arhi

@JohnOCFII said in Inconsistent results with optical encoder wheel filament sensor:

with such a large space and tolerance, I'm curious why it still would benefit from resetting on each layer

'cause in slicer I can't set it to exec something every 100 layers, or every 10 minutes, but executing something every layer is simple and supported by every slicer so I'm reseting it every layer ... normally you would need to reset the readings once or twice during a normal print only but this works so I'm not touching it any more

(and yes, the 50:5000 can probbly be 80:200 when resseting every layer but as I said, works, not touching it any more )

JohnOCFII

@arhi Excellent. Thanks for the detailed information. I'll get that a try!

arhi

@JohnOCFII yw, now, you have 2.6mm/pulse I have 0.124mm/pulse so there's huge difference in sensitivity between our sensors so you probably don't have the span as big as I do .. I think the reason I'm having these 5000% jumps are e.g. lot of retractions (PA related) and since I use rotary encore with too many pulses/rotation all those get registered while if you use less precision probably number of those will just be ignored

JohnOCFII

@arhi said in Inconsistent results with optical encoder wheel filament sensor:

@JohnOCFII yw, now, you have 2.6mm/pulse I have 0.124mm/pulse so there's huge difference in sensitivity between our sensors so you probably don't have the span as big as I do .. I think the reason I'm having these 5000% jumps are e.g. lot of retractions (PA related) and since I use rotary encore with too many pulses/rotation all those get registered while if you use less precision probably number of those will just be ignored

I've changed my distance per pulse quite a bit, as it jumps around. I've seen the measured amount be as low as 0.7 or as high as 2.6. When I thought it had settled out, I would change the L parameter. At one point I thought perhaps it was a faulty optical sensor, so I swapped that, but it remains inconsistent.

And yes, I do have a healthy retraction, as well as regular Z-hop and PA too.

John

JohnOCFII

I'm trying to eliminate variables to determine why I'm getting such inconsistent results, but I'm not making much progress.

I modified my machine profile to have no retraction and no Z-hop
I made sure Pressure Advance was disabled
I created a simple vase-mode cylinder with no top and no bottom

The print ran at 15mm/sec.

After completion, these were my results:

Pulse-type filament monitor on pin (connlcd.encb,connlcd.3), disabled, sensitivity 1.200mm/pulse, allowed movement 50% to 1500%, check every 5.0mm, measured sensitivity 0.907mm/pulse, measured minimum 27%, maximum 2377% over 521.3mm

This is my M591 command:

M591 D0 P7 C"connlcd.encb" S0 R50:1500 L1.2 E5 A1

Other than the prime line and a one layer, one loop skirt, this should have been, effectively, a simple 21 minute extrusion (plus simple vase-mode increase in Z for each layer). Does this imply I've got a physical issue? Some sticking or slipping in my sensor setup? It seems "smooth enough" when I pull filament through and watch the sensor wheel spin.

I'd love some additional ideas!

Thanks,

John

JohnOCFII

@JohnOCFII

I've replaced the axle (A and B) and tried the same vase mode print again. Results very similar with this vase mode print. Next I need to try the "per layer" change suggested by @arhi

Pulse-type filament monitor on pin (connlcd.encb,connlcd.3), disabled, sensitivity 1.200mm/pulse, allowed movement 50% to 1500%, check every 5.0mm, measured sensitivity 1.030mm/pulse, measured minimum 28%, maximum 1649% over 524.1mm

Phaedrux

I'm following along, but not sure atm how to assist, so keep us posted.

arhi

@JohnOCFII said in Inconsistent results with optical encoder wheel filament sensor:

measured minimum 27%, maximum 2377% over 521.3mm

no retractions, no PA... IMHO this can mean only two things

there is a problem with that encoder (it's sliping, or the light diode is not properly sensing the gaps, or a wire is loose, your output is floating and not properly going to Vcc/Vss, or ... dunno, something)
there is a bug in the sensor code

I can't see the third option that can explain this.

What would be interesting to test is to attach a logic analyzer to the output of the sensor going to duet and logging the data

one question about [1], how is your electronics hooked up? schematic?
The way you configured it C"connlcd.encb" is no pullup/pulldown on the duet so duet expect you have a full swing 0 to 3v3 on this pin, do you have this or you maybe need a pullup or pulldown? You can easily configure pin to use pullup by adding ^ before the pin name so C"^connlcd.encb" dunno if duet support pull down I did not try

https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Pin_names

JohnOCFII

@arhi said in Inconsistent results with optical encoder wheel filament sensor:

What would be interesting to test is to attach a logic analyzer to the output of the sensor going to duet and logging the data

Hmm... I might have an old BitScope DSO around, but I'll have to see if I have a system I can run it from. Looks like they haven't updated software in a few years.

one question about [1], how is your electronics hooked up? schematic?

I hooked it up using the same connections I was using for my simple switched-based filament sensor. I'm using Pin1 in the CONNLCD 10-pin connector for 3.3V, Pin2 for GROUND, and Pin3 which is listed as STOP 10 (ENC_B).

https://duet3d.dozuki.com/Wiki/Duet_Wiring_Diagrams

The sensor itself is a pretty basic optical endstop: https://www.ebay.com/itm/4-Pieces-Optical-Endstop-Limit-Switch-RAMPS-1-4-Board-3D-Printer-3Pin-Cable-A27/254260205504

And again, the design is from @fractalengineer https://www.thingiverse.com/thing:4445504

The way you configured it C"connlcd.encb" is no pullup/pulldown on the duet so duet expect you have a full swing 0 to 3v3 on this pin, do you have this or you maybe need a pullup or pulldown? You can easily configure pin to use pullup by adding ^ before the pin name so C"^connlcd.encb" dunno if duet support pull down I did not try

https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Pin_names

I'll try it with the pull-up.

I'll try these tomorrow. (US Central time here -- UTC-5 now for daylight saving time).

Thanks for the ideas!

arhi

the interrupter on those boards require pullup, wether pullup is already mounted on the pcb with the interrupter or not I don't know but testing with pullup on the duet is simple so nothing to lose by trying it IMHO

JohnOCFII

@arhi said in Inconsistent results with optical encoder wheel filament sensor:

the interrupter on those boards require pullup, wether pullup is already mounted on the pcb with the interrupter or not I don't know but testing with pullup on the duet is simple so nothing to lose by trying it IMHO

I added the pullup. Results seem more consistent. Still a broader range than I'd hope for a vase mode cylinder. I'll tweak the settings a bit - perhaps increase the measurement length, and try again.

Pulse-type filament monitor on pin (connlcd.encb,connlcd.3), disabled, sensitivity 1.200mm/pulse, allowed movement 50% to 1500%, check every 5.0mm, measured sensitivity 1.368mm/pulse, measured minimum 28%, maximum 428% over 521.3mm

JohnOCFII

@JohnOCFII Sadly - continued testing shows similar wild results:

Pulse-type filament monitor on pin (connlcd.encb,connlcd.3), disabled, sensitivity 3.000mm/pulse, allowed movement 30% to 1500%, check every 10.0mm, measured sensitivity 1.731mm/pulse, measured minimum 72%, maximum 2606% over 1026.4mm

I had changed the pulse sensitivity to be closer too what the measured results were on the previous tests, but now it moves again.

arhi

dunno that sound really bad, maybe move the connection to the C"^e0stop" connector, dunno if it makes a difference but I'm not getting that big span on that pin

arhi

If you can get that BitScope DSO to run I think that's a good way to move forward. Dunno if it's capable of "passtrough" grabbing like saleae, that would be ideal...

What is the interface material between the roller and the filament? And how is filament pressed to the roller? I was having a lot of slipping when my roller wheel was just a piece of PLA/ABS and since I didn't have any real flex to print it out of I made a roller wheel to have groove and added a small wide rubber band (I actually redesigned my sensor to fit that rubber band and that's the only small one I have, when it wares out I'll have to figure something new)

JohnOCFII

@arhi said in Inconsistent results with optical encoder wheel filament sensor:

dunno that sound really bad, maybe move the connection to the C"^e0stop" connector, dunno if it makes a difference but I'm not getting that big span on that pin

That'd be wild if a different connection made a difference. I'll have to think about that.

JohnOCFII

@arhi said in Inconsistent results with optical encoder wheel filament sensor:

If you can get that BitScope DSO to run I think that's a good way to move forward. Dunno if it's capable of "passtrough" grabbing like saleae, that would be ideal...

I did install the software and it appears to function. To be honest, I've never actually used it, so that may take some effort. :).

What is the interface material between the roller and the filament? And how is filament pressed to the roller?

It is a TPE roller pressing against the filament that is in a carved out channel of PTFE.

IMG_1954 2.jpeg

I've switched to a wheel with fewer, larger "spokes" as that was one recommendation from @fractalengineer

arhi

dunno how soft is that tpu, if you hold the encoder wheel witha hand and move the filament, how much force you need to apply to move it (as it will be slipping 'cause you are holding the encoder wheel) ?

a possible issue I see here is that many black plastic filaments are actually transparent to IR light and does not work reliably, or at all, as a light stop for the gap sensors. back in the day of darwin I had to tape the alu foil over the printed blade (and then painting it black with marker) going into the sensor for sensor to register it every time and at the same location. I haven't used printed wheels for more than a decade as when I make pcb's at home when I do films I have to pay for full width of the film (30 or 60cm) so I add to the film different encoder wheel designs I can later use in designes like this (high precision, low precision...).

I believe you can do the same here, just tape the piece of alu foil over the wheel and cut the holes trough alu matching holes on the plastic using a blade, black marker paint the alu foil after that and the transparency of the plastic issue should be gone

JohnOCFII

@arhi said in Inconsistent results with optical encoder wheel filament sensor:

dunno how soft is that tpu, if you hold the encoder wheel witha hand and move the filament, how much force you need to apply to move it (as it will be slipping 'cause you are holding the encoder wheel) ?

It is a semi-flex material, and printed mostly solid. I'll try that test this evening, but I'm expecting it is held pretty firmly.

a possible issue I see here is that many black plastic filaments are actually transparent to IR light and does not work reliably, or at all, as a light stop for the gap sensors. back in the day of darwin I had to tape the alu foil over the printed blade (and then painting it black with marker) going into the sensor for sensor to register it every time and at the same location. I haven't used printed wheels for more than a decade as when I make pcb's at home when I do films I have to pay for full width of the film (30 or 60cm) so I add to the film different encoder wheel designs I can later use in designes like this (high precision, low precision...).

I believe you can do the same here, just tape the piece of alu foil over the wheel and cut the holes trough alu matching holes on the plastic using a blade, black marker paint the alu foil after that and the transparency of the plastic issue should be gone

Interesting! The wheel I have in there now is actually a brown PLA plastic, but seeing the same results as with the black. I can try the foil method too -- or print in a different color/material. The black in the photograph is PETG, the current one is PLA+ .

Thanks,

John

arhi

@JohnOCFII I have not tested how each plastic is transparent to the IR but most are to some extent... alu tape is pretty simple and effective solution for that transparency... I'm not sure that's the issue you are having but at this point...

JohnOCFII

@arhi said in Inconsistent results with optical encoder wheel filament sensor:

If you can get that BitScope DSO to run I think that's a good way to move forward. Dunno if it's capable of "passtrough" grabbing like saleae, that would be ideal...

Passthrough would be ideal. Do you know how the Saleae Logic units do that? Do all the current models do that (might upgrade if so...). I'd prefer to use something that is still actively developed.