Piezo Orion + RRF 3.... Problems
-
@arhi pls gimme a example config. I will test it
-
Don't Get me started on about the Piezo Orion.
I bought a genuine one to test which arrived earlier in the week. Upon opening the packaging i'm met with printed parts that looked like they were printed by a blind man in an awful hurry.
Hey ho I think, I will re-print the parts myself properly.
then i plugged it into my test stand, a Duet 2 set up purely for testing things on the bench and it was dead, no L.E.D at boot nothing. so i take a look at the board, seems like it was hand soldered by the blind guy who did the printing with components askew an solder splashes....
One email to Precision Piezo later with the pictures included below and they reply that they think the unit was either damaged during transit or during fitting, but they refunded me, which leads to the question if they thought it was possibly a installation issue why refund me ?
Be very careful about buying this thing
-
@engikeneer said in Piezo Orion + RRF 3.... Problems:
@chop Nothing obviously out in your config, only thing I'd mention is your M350. Add 'I1' to the end of the line to enable interpolation (as long as you're sticking with x16 microstepping). Might be the default, but best to specify.
Unrelated, but I think 'B4138' in your thermistor settings is the default so probably not quite right for your setup - you'll want to find the right value to go in there for your thermistors.Back to the Z-probe. That all seems a sensible workflow to me, though obviously be very careful using M564 H0 - I'd always prefer to to home properly, or at the very least use G92 to set all positions.
I don't know anything about pertinax as a a material so can't comment on how that will affect things. Can you see any indentation after you do several probes? Your feedrate of 500mm/min is reasonably fast, but not crazy. I wonder if it is just hitting the surface a little hard.
What kind of values are you getting from your G30 S-1? Are we talking 5um steps, 20um steps, or full 0.5mm each time?Have you tried adjusting the potentiometer on the Orion? Not sure whether you'd want to go more or less sensitive. I kind of found a sweet spot when I first fitted mine and haven't adjusted it since...
Are you using the standard mount they ship with it, or something custom?
Not sure if it will help, but here is a macro I use from someone else on the forum to see probe repeatability. It homes everything first (G28), then probes at 151,151 ten times - you can obviously change this. It then spits out all the measurements and the mean & std dev into the console.
M291 P"Probe will be tested 10 times and return mean and standard deviation. Ok or Cancel?" R"WARNING" S3 ; User must click OK or cancel. G28 G30 P0 X151 Y151 Z-9999 G30 P1 X151 Y151 Z-9999 G30 P2 X151 Y151 Z-9999 G30 P3 X151 Y151 Z-9999 G30 P4 X151 Y151 Z-9999 G30 P5 X151 Y151 Z-9999 G30 P6 X151 Y151 Z-9999 G30 P7 X151 Y151 Z-9999 G30 P8 X151 Y151 Z-9999 G30 P9 X151 Y151 Z-9999 S-1P.S. apologies for the brain dump and many questions...
16.10.2020, 22:37:21 Stopped at height -0.110 mm
16.10.2020, 22:37:19 G30 S-1
16.10.2020, 22:37:15 Stopped at height -0.083 mm
16.10.2020, 22:37:12 G30 S-1
16.10.2020, 22:37:08 G30 S-1
Stopped at height -0.060 mm
16.10.2020, 22:37:08 M120 G91 G1 Z0.5 F6000 G90 M121
Stopped at height -0.060 mm
16.10.2020, 22:37:04 Stopped at height -0.055 mm
16.10.2020, 22:37:02 G30 S-1
16.10.2020, 22:36:59 Stopped at height -0.032 mm
16.10.2020, 22:36:58 G30 S-1
16.10.2020, 22:36:54 G30 S-1
Stopped at height -0.025 mm
16.10.2020, 22:36:47 G30 S-1
Stopped at height -0.002 mm
16.10.2020, 22:36:43 G30 S-1
Stopped at height -0.002 mm
16.10.2020, 22:36:37 G30 S-1
Stopped at height -0.002 mm
16.10.2020, 22:36:32 G30 S-1
Stopped at height 0.000 mm
16.10.2020, 22:36:27 Stopped at height 0.000 mm
16.10.2020, 22:36:25 G30 S-1
16.10.2020, 22:36:24 M120 G91 G1 Z0.5 F6000 G90 M121
Stopped at height 0.002 mm
16.10.2020, 22:36:24 G30 S-1
Stopped at height 0.002 mm
16.10.2020, 22:36:17 G30 S-1
Stopped at height 0.002 mm
16.10.2020, 22:36:09 G30 S-1
Stopped at height 0.002 mm
16.10.2020, 22:36:03 G30 S-1
Stopped at height 0.005 mm
16.10.2020, 22:35:53 G30 S-1
Stopped at height 0.005 mm
16.10.2020, 22:35:44 G30 S-1
Stopped at height 0.005 mm
16.10.2020, 22:35:35 G30 S-1
Stopped at height 0.007 mm
16.10.2020, 22:35:25 G30 S-1
Stopped at height 0.010 mm
16.10.2020, 22:35:16 Stopped at height 0.010 mm
16.10.2020, 22:35:15 G30 S-1
16.10.2020, 22:35:07 G30 S-1
Stopped at height 0.007 mm -
16.10.2020, 22:43:59 Error: Z probe readings not consistent
16.10.2020, 22:43:38 Error: Z probe readings not consistent
16.10.2020, 22:43:13 Error: Z probe readings not consistent -
-
@chop said in Piezo Orion + RRF 3.... Problems:
@arhi pls gimme a example config. I will test it
you need to run the analog output to the zprobe.in using a coax cable (I'm using balanced audio cable for e.g.)
config:
; ORION ANALOG M558 P1 C"!zprobe.in" R2 H6 F2400 T3600 A4 S0.03 K0 G31 X0 Y0 Z-0.1 P250how to use it:
homez.g; HOME Z WITH ORION M400 T0 G90 G0 X0Y0 F3000 ; go to center of the bed, complain if X or Y not homed G91 ; relative positioning ;G0 Z5 F900 H2 ; drop bed for 5mm G90 ; absolute positioning G4S3 ; wait 3sec G31 P{sensors.probes[0].value[0] + 3} G30 ; Probe the bed at the current XY position. ; When the probe is triggered, set the Z coordinate ; to the probe trigger height.the G31 here takes current reading from the analog input and set treshold to +3 that value
bed.g
; bed.g ; called to perform automatic bed compensation via G32 G29 S2 ; delete compensations M561 ; clear any bed transform G28 ; home M400 M913 X30 Y30 Z100 ; go to first test point M400 G4 S1 M400 G31 P{sensors.probes[0].value[0] + 3} G29 S0this way the issue with sh$%%^tty potentiometer on the board for setting trashold for digital output is solved.
There's still issue with mounting ppiezo but that's another bag of worms, but this is the good start so you at least have treshold set right.
notice that if you are having "premature trigger" with
G31 P{sensors.probes[0].value[0] + 3}you can change to +5 or more, but that really means that you are picking up a lot of noise and you need a better cable or that your head is vibrating or .. it should work with +2 or +3
-
also note that you want probing to be "fast" as the fastes you hit the nozzle better it will react, piezo do not like to be "slowly pressure" it likes to be tapped. The problem with current firmware is that it slows down when the read value is close to treshold (and it always is as it does not change like with ir sensor). dc42 said he'll change this in one of the next versions but so far it has not happened so you need to push the speed in the m558
-
thanky you. but how can i adjust the trigger?
-
@chop said in Piezo Orion + RRF 3.... Problems:
thanky you. but how can i adjust the trigger?
this does it:
G31 P{sensors.probes[0].value[0] + 3}analog output from the orion ignores the pot, so don't touch the pot.
this reads the current value of the analog output from the orion (sensors.probes[0].value[0]and sets the new treshold value to read value+3 -
@arhi hm . changed from 1 to 25 and nothing changed
-
@chop what do you expect to change?
-
@arhi the trigger value in dwc its @ 492 and with s lot of preasure it Gos over 500
-
@chop what you see in DWC is the read of the analog value, that will not change by any g-code, it's what the orion is sending and it changes as the orion is deformed. the G31 I gave you changes the threshold. to see the threshold value you need to send just G31
-
@arhi ah okay. Ty! Today i will give some anti backlash nuts a shot. After install i will try your Tipps.
-
So it works! Thank you for your help. But now I have the next problem. How can I use the orion correctly? How do I set z. no matter what I do . He starts printing in the air. With rrf3 I determine z with 92z0 right? Then I create a mesh. What do I have to enter in his? I'm still new to rrf. before marlin sorry. do not quite understand all of this yet
-
@chop now you need to manually figure out the Z offset of the probe and put it in the config.
- super important is that you heat up your bed and nozzle before you home Z with the orion
- super important that you clean a nozzle before you probe (so heat up, wipe, retract, wipe is what I do, visually inspect when nozzle is sitting above center of the bed that nozzle is clean)
- after you home Z, you then need to find the "offset"
this offset is normally in the range of 0 to -0.1mm depending on how sensitive your orion is and how fast you probe so it's basically the travel your bed does during a trigger delay. how to setup this offset ... ppl have different preferences, what I do is I'd leave nozzle in the center of the bed (homing position) and do
G0Z1this should have your nozzle close to the bed but not touching it
disable soft limits
M564 S0 H0now I put piece of paper between nozzle and bed and start reducing this value
G0Z0.5G0Z0.3
G0Z0.2
...
G0Z-0.2
...till I get to point that paper is being grabbed by the nozzle
this position need to be your Z0 so see how far you are from it (you know what Z value you gave it), change the sign of that value and put in the config of the probe (G31, the Z value):
e.g.:G31 X0 Y0 Z-0.1 P250
hope this helps
btw, do this while everything is HOT and nozzle is clean. Otherwise not much point in using orion, as if you probe cold those are not real value during print.... this is why I like the durable print surfaces like printbite as if you have those soft print surfaces they can dislike the hot nozzle so then you might want to work hot but heat up the bed to your print temperature but heat up the nozzle to lower temp like 100-120C enough for it to "get bigger" but not hot enough to damage the print board if you mess something up
useful read: https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe
-
one hint, since digging hot nozzle into print bed is a real solution when you do this first time I suggest you use a PCB on top of your print bed, or use glass as your print surface for the first test... so both probe over the hard surface that's temperature resistent (pcb/FR4 or glass) and start the first print on top of such surface to be sure you got the probing and configuration (offset) properly calibrated
going further, one other hint .. before you start printing, make sure that ORION Is ok and that you are not drowning in noise .. so run a test probing same point many times
-
@arhi ty . I will try. But, how to set z0 corect? After z0 i can set offset !? Right? Once i get the offset. I have to tell the Slicer to use the mesh?
-
@arhi said in Piezo Orion + RRF 3.... Problems:
@chop now you need to manually figure out the Z offset of the probe and put it in the config.
- super important is that you heat up your bed and nozzle before you home Z with the orion
- super important that you clean a nozzle before you probe (so heat up, wipe, retract, wipe is what I do, visually inspect when nozzle is sitting above center of the bed that nozzle is clean)
- after you home Z, you then need to find the "offset"
this offset is normally in the range of 0 to -0.1mm depending on how sensitive your orion is and how fast you probe so it's basically the travel your bed does during a trigger delay. how to setup this offset ... ppl have different preferences, what I do is I'd leave nozzle in the center of the bed (homing position) and do
G0Z1this should have your nozzle close to the bed but not touching it
disable soft limits
M564 S0 H0now I put piece of paper between nozzle and bed and start reducing this value
G0Z0.5G0Z0.3
G0Z0.2
...
G0Z-0.2
...till I get to point that paper is being grabbed by the nozzle
this position need to be your Z0 so see how far you are from it (you know what Z value you gave it), change the sign of that value and put in the config of the probe (G31, the Z value):
e.g.:G31 X0 Y0 Z-0.1 P250
hope this helps
btw, do this while everything is HOT and nozzle is clean. Otherwise not much point in using orion, as if you probe cold those are not real value during print.... this is why I like the durable print surfaces like printbite as if you have those soft print surfaces they can dislike the hot nozzle so then you might want to work hot but heat up the bed to your print temperature but heat up the nozzle to lower temp like 100-120C enough for it to "get bigger" but not hot enough to damage the print board if you mess something up
useful read: https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe
Make sure the dynamic test is successful (Z probe stops when it senses the bed) before doing this.
Cancel any currently active mesh compensation with M561
Use the X and Y jog buttons to position the nozzle over the centre of the bed
Jog the nozzle down until it is just touching the bed or just gripping a sheet of paper. If the firmware doesn't let you jog it down far enough, send M564 S0 to disable axis limits.
Once you have the nozzle touching the bed, send command G92 Z0 to tell the firmware that the head is at Z=0
Jog the head up by 5 to 10mm
Send command G30 S-1. The nozzle will descend or the bed rise until the probe triggers and the Z height at which the probe stopped will be reported. If you are using a nozzle-contact Z probe, the trigger height will be slightly negative. For any other type of Z probe where the probe triggers before the nozzle contacts the bed, it will be positive.
Repeat from step 5 two or three times to make sure that the trigger height is consistent.
In Duet Web Control, go to Settings -> System Editor and edit the config.g file. Set the Z parameter in the G31 command to the trigger height that was reported. Save the file.
Open config-override.g and check that there are no G31 commands in it. If you find any, delete those lines and save the file.
To apply the new trigger height, restart the Duet by sending M999 or pressing Emergency Stop.Thats what i do...print starts mid air
-
testing the repeatability - very important with piezo
G28 M401 G30 P0 X151 Y161 Z-9999 G30 P1 X151 Y161 Z-9999 G30 P2 X151 Y161 Z-9999 G30 P3 X151 Y161 Z-9999 G30 P4 X151 Y161 Z-9999 G30 P5 X151 Y161 Z-9999 G30 P6 X151 Y161 Z-9999 G30 P7 X151 Y161 Z-9999 G30 P8 X151 Y161 Z-9999 G30 P9 X151 Y161 Z-9999 S-1 M402change X and Y values to be in the center of your bed
more details here: https://forum.duet3d.com/topic/6962/m48-measure-z-probe-repeatability-and-print-to-serial-output/4
