Duet 3 Output Not Working

Veti

@beachtec said in Duet 3 Output Not Working:

M584

also see
https://duet3d.dozuki.com/Wiki/Gcode#Section_M584_Set_drive_mapping

VERY IMPORTANT! Assigning a drive using M584 does not remove its old assignment. Therefore, if you assign a drive that defaults to being an extruder drive, you should also assign the extruder drives explicitly as in the above example. Failure to do so may result in unexpected behaviour.

so do one M584 statement

beachtec

@JoergS5 That is interesting because my general guidance here has been from following @dc42's awesome wordpress blog https://github.com/Duet3D/RRF-machine-config-files/blob/master/E3D_Tool_Changer/dc42-duet3-centreZero-2Titan-2Hemera/sys/config.g... here it is as a cut and paste:


; Network
M550 P"ToolChanger" 			; Set machine name
M552 P192.168.1.153 S1			; Enable Networking
M586 P0 S1 						; Enable HTTP
M586 P1 S0 						; Disable FTP
M586 P2 S0 						; Disable Telnet

M667 S1 						; Select CoreXY mode	

; Drive direction
M569 P0 S1 						; Drive 0 Z
M569 P1 S0 						; Drive 1 Y
M569 P2 S0 						; Drive 2 X
M569 P3 S0 						; Drive 3 E0
M569 P4 S0 						; Drive 4 E1
M569 P5 S0 						; Drive 5 COUPLER
M569 P22.0 S0 D2				; Drive 22.0 (E2) spreadCycle mode
M569 P23.0 S0 D2 				; Drive 23.0 (E3) spreadCycle mode

M584 X2 Y1 Z0 C5				; Axis to driver mapping
M584 E3:4:22.0:23.0				; set extruder drivers

M208 X-185:178.5 Y-149:49 Z0:300 C0:500					; Set axis maxima & minima
M92 X100 Y100 Z1600 C200 E834:834:409:409				; Set steps per mm assuming x16 microstepping
M350 E16:16:16:16 I1 									; Configure microstepping with interpolation
M350 C16 I1
M350 X16 Y16 Z16 I1										; Configure microstepping with interpolation
M566 X400 Y400 Z8 C2 E200:200:200:200					; Set maximum instantaneous speed changes (mm/min)
M203 X35000 Y35000 Z1200 C10000 E5000:5000:5000:5000	; Set maximum speeds (mm/min)
M201 X6000 Y6000 Z400 C500 E2500:2500:2500:2500			; Set accelerations (mm/s^2)
M906 X2000 Y2000 Z1330 C500 E1400:1400:1000:1000 I30	; Set motor currents (mA) and motor idle factor in percent
M84 S120 												; Set idle timeout

@DC42 is a kind of Ninja to me and his M584 section here has 2 entries; I thought maybe the Hermera(s) (running on ILC toolboard's over the CAN bus) might need a separate one... I mean @dc42 put it in HIS config.g file. That said, I have shrunk it to one... and the problem remains...
I would LOVE to sort this!!!... and thank you all for trying to help!!!

JoergS5

@beachtec you confuse me with @Veti , the M584 was from him, the M906 comment was from me.
Did you change the M commands to have 2 entries for E?
Can you please repost the config how it is now? Maybe it's not moving because the endstops have a problem and are triggered from the beginning.

And I did not understand completely your first description: is it in slot 5 or 0 which is not working? Is an endstop assigned to the slot which is not working?

beachtec

@JoergS5 I am sorry for any confusion. Stepper 5 is NoOp. Steppers 3,4,5 are configured together to be the Z-axis. Motors 3,4 run and behave correctly. Swapping connectors with stepper 5, the new motor attached to stepper 5 connector does not function while the MOTOR that WAS connected to stepper 5 works fine in another position on the z-axis. I have commented out the stops (making no difference). Just trying to simplify and reduce the problem surface. I will post it in a few minutes. @JoergS5 , thank you for looking at this!!!

Phaedrux

Are you getting any error messages in the console when you try to move the motors?

https://forum.duet3d.com/topic/18011/duet-3-6hc-short-to-ground-issue

Please check if your Duet 3 may be affected by this known issue.

JoergS5

@beachtec a different thing is that the M92 for Z is wrong.
M92 Z1600 ; Steps/mm for Z - TR8*4 / 0.9 deg stepper
400 steps per rotation with M350 Z8 => 3200 steps for 4 mm => Z800 would be correct.

beachtec

@beachtec Lucky me. I have seen that error msg. My board# is WD41-412

beachtec

@JoergS5 all 1.8 degree steppers (except the Hermera of course) ...

JoergS5

@beachtec so I was fooled by the comment...

Back to your problem, I think the first step to analyze would be to isolate the problem and test stepper 5 connector as single drive configuration (for drive X eg). If this works, the 3-drive-Z can be tested. Because now it could be a defective driver, a configuration issue, a wiring issue or something else.

beachtec

@JoergS5 Fair enough... I should have probably done that before I posted! I will test a file and publish the results.

JoergS5

@beachtec you don't need a file, you can move the steppers by direct g-code commands in the "Send G-Code" field of the DWC duet web control. That's one of the advantages of Duet, the direct execution of all commands (with the exception of some config settings).
(> sorry if this bothers you, I don't know whether you are familiar with Duet).

beachtec

I wrote one anyway to try on a few different axis. Stepper 5, nothing. Other steppers work with the same settings.

beachtec

@JoergS5 I am very grateful for the help and am always learning... do not worry about bothering me at all! I am good!

beachtec

and I love that command line window!

JoergS5

@beachtec if driver 5 is defective, the common procedure is to look at the Duet 3 whether a defect is visible for warranty, so detailed images of front and back of the stepper 5 driver would be the next step. Inspections would be made by the moderators/administrators.

It's confusing that M122 shows no errors for driver 5, so I expect that the driver is not defect. Maybe a connection problem of the connector?

beachtec

I do not understand it either. I believe that if the wiring was at fault, the stepper driver would have worked when a motor known to be working well was swapped out and the power was cycled. But when I did that. The drive I motor I swapped into Drive 5 did not work and the motor formerly in drive 5... worked fine in the new location. I would MUCH rather fix it then replace it... it's a lot of time and delays... but I understand. By the way, I wanted to redo all of my connectors doing this but there was just enough to do the job in my box but I tested them and they all show good connections, and the same Impedance and coil phasing. I have only had it a few days... been waiting to work on it this weekend. Duet Driver 5 Rear.jpg Duet Driver 5.jpg

JoergS5

@beachtec you'll have to wait for the experts. Good luck!!

Phaedrux

Did you check out that link I posted? Send an email to see if you're affected by the diode problem. If so, replacement is really the only way to go.

beachtec

@Phaedrux, @JoergS5, @T3P3Tony Epilogue.

Thank you for your help with this issue.

This forum is loaded with great people, support and solutions that drive a deeper understanding of your products and the creative ways they can be used.. it is straight up good reading, I always learn something and sometimes even gain a bit of humility!

I had my replacement Duet 3 sent overnight and installed it straight away... within minutes everything was working properly, even a few little issues I had with noise on drive 0 and 1, which seemed like it might just be tuning, were cleared up and the machine performed perfectly. I love drivers on this board, it is so quiet!

Anyway, thank you again for your help and support. Cheers!

JoergS5

@beachtec nice to hear that it has a good end. Happy printing!