Problems with Configuration Tool
-
I had a defective SD card and unfortunately due to a PC change no backup. So I had to reset my Delta Printer and changed to the new firmware. I used the Config Tool. DuetWifi and SW 3.0. The two PT1000 sensors show wrong ( what worked fine under the 2.x. Homing does not work anymore ( goes to the endstops and instead of shutting down, it stops at the switched endstops. It is not possible to create a reasonable config.g with this tool. Z-Endstop is grayed out and cannot be selected. The parameters for the sizes don't fit either ( e.g. printable area maximum 105mm and that where I have a 300mm print bed). The config is hardly suitable as a first clue.
0:/sys/config.g
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Mar 08 2020 13:43:36 GMT+0100 (Mitteleuropäische Normalzeit); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name
M665 R175 L386 B145 H380 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z160.00 E450.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 Z0 S1 ; set minimum Z; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
;M574 Z1 S1 P"null" ; configure active-high endstop for low end on Z via pin null
M574 Z1 S1 P"zstop"; Z-Probe
M558 P5 R0.4 C"zprobe.in+zprobe.mod" H5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds
M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 R85 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
My Printer
Send code...
Status
Idle
Mode: FFF
Tool Position
X
0.0
Y
0.0
Z
380.00
Extruder Drives
Drive 0
0.0
Speeds
Requested Speed
0 mm/s
Top Speed
0 mm/s
Sensors
Vin
24.3 V
MCU Temperature
30.1 C
Z-Probe
0
Tools
Extra
Control All
Tool Heater Current Active Standby
Tool 0
T0 - Load Filament Heater 1
off 168.9 C
0
0
Bed Heater 0
off 169.4 C
0
0
Temperature Chart
System Directory; homedelta.g
; called to home all towers on a delta printer
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Mar 08 2020 13:45:33 GMT+0100 (Mitteleuropäische Normalzeit)
G91 ; relative positioning
G1 H1 X265 Y265 Z265 F1800 ; move all towers to the high end stopping at the endstops (first pass)
G1 H2 X-5 Y-5 Z-5 F1800 ; go down a few mm
G1 H1 X10 Y10 Z10 F360 ; move all towers up once more (second pass)
G1 Z-15 F6000 ; move down a few mm so that the nozzle can be centred
G90 ; absolute positioning
G1 X0 Y0 F6000 ; move X+Y to the centreThen i wanted to switch back to a 2.x version..but that dont work..updated it and its still the 3.0 version..
any hints for me?
just tried again..downloaded the latest version..uploaded it to the printer...started the update and got this
M997 S0
Error: In-application programming binary "Duet2CombinedIAP.bin" not found -
that really drives me crazy..used the config tool over and over again...finally i got the 2 PT1000 back to work...even had one Calibration via G32..put the new numbers into my M665 and M666 but now my Homing dont work...he runs into endstops...lower 10mm and makes a 2nd run..goes up into endstops and stops there..the dont lower again...
; homedelta.g
; called to home all towers on a delta printer
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Mar 08 2020 17:21:54 GMT+0100 (Mitteleuropäische Normalzeit)
G91 ; relative positioning
G1 H1 X380 Y380 Z380 F1800 ; move all towers to the high end stopping at the endstops (first pass)
G1 H2 X-10 Y-10 Z-10 F1800 ; go down a few mm
G1 H1 X20 Y20 Z20 F360 ; move all towers up once more (second pass)
G1 Z-30 F6000 ; move down a few mm so that the nozzle can be centred
G90 ; absolute positioning
G1 X0 Y0 F6000 ; move X+Y to the centre
with that homedelta it worked before but not anymore...and because homing dont work i get this error message
G28
Error: G0/G1: target position not reachable from current positionsame with g32
G32
Error: G0/G1: target position not reachable from current position -
Can you check that version 3 firmware was actually applied? Send M115 to check version.
Duet2CombinedIAP.bin is in the same release as the 3.0 firmware. You need that file present on the SD card to be able to roll back to the previous 2.x firmware.
Unfortunately, I'm not sure about your delta homing problem.
-
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-01-03b3
strange..schouldnt it be something with RC3? it was the last version..anyway...the homing prob is very odd...because if it occours i have to turn off the printer and sometimes it works after that cold reset
-
ok..solved the Homing Problem...checked it several times that i choosed the active high endstops but in config.g they were active low...
Holy sh?* my first config after i bought the duet wifi was so easy compared to bring my Delta back to live now
