RepRapFirmware 3.01beta1 released

kraegar

Here is the version that works well:

M561                         ; clear any existing bed transform
; If the printer hasn't been homed, home it
if !move.axes[0].homed || !move.axes[1].homed || !move.axes[2].homed
  G28
  
G1 Z7.5

;Run initial 4 point leveling routine
G30 P0 X15 Y45 Z-99999
G30 P1 X15 Y227.5 Z-99999
;G30 P2 X235 Y125 Z-99999 S3
G30 P2 X235 Y227.5 Z-99999
G30 P3 X235 Y45 Z-99999 S3



while true
  if iterations = 5
    abort "Too many auto calibration attempts"
  if move.initialDeviation.deviation < 0.01 
    if move.calibrationDeviation.deviation < move.initialDeviation.deviation + 0.005
      if move.calibrationDeviation.deviation > move.initialDeviation.deviation - 0.005
        break
  echo "Repeating calibration because initial deviation (" ^ move.initialDeviation.deviation ^ "mm) must be < 0.01"
  echo "and (" ^ move.calibrationDeviation.deviation ^ "mm) must be within 0.005 of initialDeviation"

  G30 P0 X15 Y45 Z-99999
  G30 P1 X15 Y227.5 Z-99999
  ;G30 P2 X235 Y125 Z-99999 S3
  G30 P2 X235 Y227.5 Z-99999
  G30 P3 X235 Y45 Z-99999 S3

echo "Auto calibration successful, deviation", move.calibrationDeviation.deviation ^ "mm"
echo "Auto calibration successful, initialDeviation", move.initialDeviation.deviation ^ "mm"  
    
G28 Z

G1 X0 Y0 F24000               ; move the head to the corner (optional)

And removing the nested if's to replace with && crash it

  if move.initialDeviation.deviation < 0.01 && move.calibrationDeviation.deviation < move.initialDeviation.deviation + 0.005 && move.calibrationDeviation.deviation > move.initialDeviation.deviation - 0.005
        break

Edit: I realize I could just have some major syntax issues, still figuring this out. But that's a hard crash if you do that

carlosspr

@carlosspr Solved. I was missing M584 drive mapping on config.g

dc42

@kraegar said in RepRapFirmware 3.01beta1 released:

And removing the nested if's to replace with && crash it

Thanks, I've reproduced the crash by adding that line to my own script. I will look into it. Even if you do make a syntax error, you should get a helpful error message.

PS - now I know that the new crash handler I added for uncaught exceptions works!

Last software reset at 2020-01-15 16:35, reason: Terminate called, spinning module GCodes, available RAM 9464 bytes (slot 2)

kraegar

Trying to test if move.initialDeviation.deviation is 0.000

if move.initialDeviation.deviation != 0
  echo "one " ^ move.initialDeviation.deviation

I've tried using 0.000 as well, with the same result. == 0.000 or == 0 doesn't match, even though it is.

(I'm trying to determine if leveling has been run at all yet, my only clear method for now is to see if initial and calirbated deviation and mean are all 0.000)

dc42

Just done some tests. There is a problem with equality between floats.

The other problem you had is because the GCode line was too long. I changed it to throw an exception when that happens, but the exception isn't caught.

This is all very new code, so I was expecting some bugs.

kraegar

Yep, I'm just playing, happy to just keep reporting. Variables will clean the code up a lot, but that's a big ask

kraegar

Once variables are implemented, if they're "system wide" and not constrained to the macro they're called in, I would set a "is_level = false" in config.g, and set to true once leveling is run. Negating the need for this method of checking.

But I can't resist playing

dc42

Thanks for your reports. These two issues are now fixed in the latest builds at https://www.dropbox.com/sh/3azy1njy3ayjsbp/AACquxr2m00eV568RZg5QG5wa?dl=0.

kraegar

Can I just say, HUGE thank you!
I've already made a script to tune PA, Temp, and Extrusion % (just call the macros via layer change) as well as the auto-leveling and a "pre-print" systems readiness check.

This is amazing!

kraegar

Float comparisons are now working, and the other errors gracefully:

Error: in file macro, line 20 column 1: GCode command too long

Thanks!

dc42

Thanks for confirming. FWIW, maximum GCode line length excluding leading white space, line number and checksum (if present) and comments is currently 160 characters.

kraegar

We're going to need line numbers in the file editor in DWC now

4lathe

Can I use that new duet2combinedfirmware.bin on my maestro? The 3.01 was duetmaestrofirmware.bin.

DIY-O-Sphere

@4lathe
It's still DuetMaestroFirmware.bin

DIY-O-Sphere

@dc42
Hi David, maybe I have found a bug....
For testing I was back on 2.05 on a Maestro (DWC 2.06) and I was not able to get back directly to 3.01b.
Flashing 3.0 stable worked.

dc42

@DIY-O-Sphere said in RepRapFirmware 3.01beta1 released:

For testing I was back on 2.05 on a Maestro (DWC 2.06) and I was not able to get back directly to 3.01b.

Read the upgrade notes!

gtj0

@dc42 said in RepRapFirmware 3.01beta1 released:

Thanks for confirming. FWIW, maximum GCode line length excluding leading white space, line number and checksum (if present) and comments is currently 160 characters.

Are you sending them via text message???

DIY-O-Sphere

@dc42 said in RepRapFirmware 3.01beta1 released:

Read the upgrade notes!

Sorry....The one who can read is in advantage

dc42

@gtj0 said in RepRapFirmware 3.01beta1 released:

@dc42 said in RepRapFirmware 3.01beta1 released:

Thanks for confirming. FWIW, maximum GCode line length excluding leading white space, line number and checksum (if present) and comments is currently 160 characters.

Are you sending them via text message???

Hadn't you noticed your smartphone bills going up every time you print?

gtj0

@dc42 said in RepRapFirmware 3.01beta1 released:

@gtj0 said in RepRapFirmware 3.01beta1 released:

@dc42 said in RepRapFirmware 3.01beta1 released:

Thanks for confirming. FWIW, maximum GCode line length excluding leading white space, line number and checksum (if present) and comments is currently 160 characters.

Are you sending them via text message???

Hadn't you noticed your smartphone bills going up every time you print?

Ah that makes sense now. I though it was the cat texting his buddy across the street.