BLTouch/Fried board

jay_s_uk

@StevenHerbs please start your own thread

StevenHerbs

I intentionally replied to this thread instead of starting my own because of the similarities.

I'd been hoping @dc42 would be able to weigh in on this.

A Former User

@StevenHerbs By any chance does your BLtouch have the word creality anywhere ? If so the wiring is different. That has caused many a board to release the magic smoke.

droftarts

@StevenHerbs please post a picture of your wiring, at the Duet and at the BLTouch.

U3 is the 5V regulator, and while a short to ground can make it fail, feeding it 24V is the only way to make it go up in flames. Did it go up straight away after turning on? I’d check proximity to hot end heater wires in cable runs, look for a short between that and the 5V or servo wire.

It may be repairable. You can replace U3, see https://docs.duet3d.com/en/User_manual/Troubleshooting/Parts#voltage-regulators-1

Ian

StevenHerbs

@KenW said in BLTouch/Fried board:

@StevenHerbs By any chance does your BLtouch have the word creality anywhere ? If so the wiring is different. That has caused many a board to release the magic smoke.

No, zero chance. I have both and it's impossible to confuse the two. This is 100% genuine BLTouch V3.1 from Antclabs.

@droftarts said in BLTouch/Fried board:

@StevenHerbs please post a picture of your wiring, at the Duet and at the BLTouch.

U3 is the 5V regulator, and while a short to ground can make it fail, feeding it 24V is the only way to make it go up in flames. Did it go up straight away after turning on? I’d check proximity to hot end heater wires in cable runs, look for a short between that and the 5V or servo wire.

It may be repairable. You can replace U3, see https://docs.duet3d.com/en/User_manual/Troubleshooting/Parts#voltage-regulators-1

Ian

Thanks for the info. No, it took part of a minute before it started shooting open flame. I didn't install the BLTouch on the carriage yet - I had it loose by the board, so the cabling wasn't anywhere close other wires to short.

StevenHerbs

Apologies - originally missed the request for the BLTouch end of the wiring.

sebkritikel

@StevenHerbs Looks to me as if your 5-pin plugged into the BLTouch is backward. From left to right it should be:

Are you using the geniune cable? Perhaps you used the Creality one on accident?

Above info taken from the Zprobe docs, image below for reference.

StevenHerbs

@sebkritikel

You've got to be kidding me......that's such a simple explanation. It hadn't occurred to me that the wiring order at the BLTouch might have different standards. I hadn't found those charts you shared before, but that explains everything. While the BLTouch IS authentic from Antclabs, it is boxed in a Creality box and wired for Creality applications.

At least I understand the reason and how to avoid a repeat. Thank you!

A Former User

@StevenHerbs That was why I ask if it was associated with Creality in any way. That little change by Creality has caused many cases of magic smoke release. Both by Creality board owners who bought a non Creality BLtouch and vice versa.

sebkritikel

@StevenHerbs Sorry to be the bearer of bad news! Hopefully you try that U3 replacement, as that might work out for you!

Agree with @KenW, for reasons unknown Creality and Co have screwed with plenty of DIYers with their change.

oliof

@sebkritikel and to add insult to injury, wire order and colors are depending on the lot you get.