Multiple motion system homing malfunction

SANJR

daemon.g and macro files

;daemon.g
while (true)
    M596 P1
    G91
    while (global.weldtorchstate == 1)
    G1 H4 U99999 F1000 ;selects the U axis & sets the feedrate
    G4 S0.2

; Weld Torch ON
M42 P3 S0            ; turns on the relay to start welder
M42 P4 S1            ; set U axis endstop to high
; set weldtorchstate to ON
set global.weldtorchstate = 1

; Weld Torch OFF
M42 P3 S1 ; turns off the relay
M42 P4 S0 ; set U axis to low end
; set weldtorchstate to OFF
set global.weldtorchstate = 0

SANJR

@T3P3Tony said in Multiple motion system homing malfunction:

@SANJR please post your config.g, the homing files, daemon.g and the macros you refer to.

Hi Tony pasted the filesplz take a look .......

SANJR

@o_lampe said in Multiple motion system homing malfunction:

@SANJR I believe you have to rethink the daemon.g code or the macros. They should only be active after x,y,z-axes are homed.
You can check for homed axes in the object model.

I'm not sure where the variables for homed axis can be found, maybe someone else can chime in?

Hi

Yes you are correct. The daemon and the macros needs to be active after homing the first motion X,Y,Z axis. I have pasted all the files plz take a look......

And about checking for the homed axes in the object model? Sorry not able to understand where and how to check the object model.... Apologies i am not able to understand.......

o_lampe

@SANJR said in Multiple motion system homing malfunction:

;daemon.g
while (true)
    M596 P1
    G91
    while (global.weldtorchstate == 1) ; maybe an if-condition would be better here?
    G1 H4 U99999 F1000 ;selects the U axis & sets the feedrate

G4 S0.2 ; this delay should be related to the while(true) loop

SANJR

@o_lampe

Thanks

Modified the daemon file

Problem still exists.

OwenD

You have no indentation in your second while statement.

SANJR

@OwenD said in Multiple motion system homing malfunction:

You have no indentation in your second while statement.

Hi Owen,

Is it the while (global.weldtorchstate == 1) refereing to?
And indentation meaning.....could u plz show it in the code plz

oliof

@SANJR

daemon.g
while (true)
    M596 P1
    G91
    while (global.weldtorchstate == 1) ; maybe an if-condition would be better here?
        G1 H4 U99999 F1000 ;selects the U axis & sets the feedrate

G4 S0.2 ; this delay should be related to the while(true) loop

SANJR

@oliof

Thanks oliof

Will check with the indentation modified

SANJR

@OwenD said in Multiple motion system homing malfunction:

You have no indentation in your second while statement.

Thanks Owen

By changing the indentation was able to get it right

SANJR

@oliof said in Multiple motion system homing malfunction:

@SANJR

daemon.g
while (true)
    M596 P1
    G91
    while (global.weldtorchstate == 1) ; maybe an if-condition would be better here?
        G1 H4 U99999 F1000 ;selects the U axis & sets the feedrate

G4 S0.2 ; this delay should be related to the while(true) loop

Thanks Oliof

Its good now