error regarding temps

DennisD

hi i got a question regarding this error.

Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature could reach 576C

i did the following changes to my creality cr 10 s Pro version frame.

removed old stock motherboard and inserted the duet motherboard.
used the flat cable and refitted all cables so it's still plug and play.
used a bondtech DDS with pancake stepper and E3D V6 kit.

now when i start the printer. its working but i get a error
i did a pid tune and inserted the outcome in the config.g

but i think i made more errors so thats why i put in the config i have.. hope u can see more errors
and help me a bit with them please. .

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)

; General preferences

G90                                           ; send absolute coordinates...
M83                                           ; ...but relative extruder moves
M550 P"Duet-Wifi-CR10SPRo"                    ; set printer name
M918 P1 E4 F2000000                           ; configure direct-connect display

; Network
M552 S1                                       ; enable network
M586 P0 S1                                    ; enable HTTP
M586 P1 S0                                    ; disable FTP
M586 P2 S0                                    ; disable Telnet

; Drives
M569 P0 S0                                    ; physical drive 0 goes backwards
M569 P1 S0                                    ; physical drive 1 goes backwards
M569 P2 S0                                    ; physical drive 2 goes backwards
M569 P3 S0                                    ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                              ; set drive mapping
M350 X16 Y16 Z16 E16 I1                       ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E415                ; set steps per mm        
M566 X1200.00 Y1200.00 Z24.00 E300.00         ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00       ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00         ; set accelerations (mm/s^2)
M906 X900 Y900 Z900 E600 I50                  ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                       ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                              ; set axis minima
M208 X300 Y300 Z260 S0                        ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                           ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                           ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                           ; configure active-high endstop for low end on Z via pin zstop    

; Z-Probe
;M558 P0 H5 F120 T6000                         ; disable Z probe but set dive height, probe speed and travel speed
;M557 X15:215 Y15:195 S20                      ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950            ; configure sensor 0 as PT1000 on pin bedtemp
M950 H0 C"bedheat" T0                         ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.405 C736.635:736.635 D7.91 S1.00 V24.2 B0
M307 H1 R1.864 C159.2 D8.88 S1.00 V24.1
M140 H0                                       ; map heated bed to heater 0
M143 H0 S60                                   ; set temperature limit for heater 0 to 60C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e1temp
M950 H1 C"e0heat" T1                          ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                              ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S260                                  ; set temperature limit for heater 1 to 260C

; Fans
M950 F0 C"fan0" Q500                          ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                          ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                             ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500                          ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1:0 T45                           ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                              ; define tool 0
G10 P0 X0 Y0 Z0                               ; set tool 0 axis offsets
G10 P0 R0 S0                                  ; set initial tool 0 active and standby temperatures to 0C
T0
; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                             ; enable support for PanelDue
M501                                          ; load saved parameters from non-volatile memory

config.override

; config-override.g file generated in response to M500 at 2023-01-21 19:30
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 R0.405 C736.635:736.635 D7.91 S1.00 V24.2 B0
M307 H1 R1.864 C159.2 D8.88 S1.00 V24.1
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00
M486 S-1

homeall.g

; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-305 Y-305 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-305 Y-305 F240  ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-265 F240        ; move Z down stopping at the endstop
G90                     ; absolute positioning
G92 Z0                  ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 Z5 F100             ; lift Z relative to current position
;G90                    ; absolute positioning

start.g

T0M92 E415; set new E-step value for Bondtech BMG Extruder

homex.g

; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 X-305 F3000 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000    ; go back a few mm
G1 H1 X-305 F240  ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

homey.g

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y-305 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000    ; go back a few mm
G1 H1 Y-305 F240  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

homez.g

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Wed Jul 28 2021 18:02:58 GMT+0200 (Midden-Europese zomertijd)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Z-265 F3000 ; move Z down until the endstop is triggered
G92 Z0            ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91              ; relative positioning
;G1 Z5 F100       ; lift Z relative to current position
;G90              ; absolute positioning

jay_s_uk

That "error" is a warning and not an error. It's just the temperature the firmware thinks the hotend could get to if it was left on with no temperature control.

DennisD

@jay_s_uk
but i never seen such warning.. why does it come up now?

jay_s_uk

@DennisD it comes up when you send M98 P"config.g"
its always there, you just don't see it on boot up because DWC usually connects after its been sent