BLTouch Not working Duet 2 WIfi
-
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Wed Feb 23 2022 21:56:24 GMT-0500 (Eastern Standard Time); General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Creality CR6SE w/ BLtouch" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X235 Y235 Z250 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first toolbolded text -
@quinn I'd suggest revisiting the configurator, you've not got any of the correct config for BLTouch in there.
Which pin are you using as the servo control?
-
Can you send M122 and M98 P"config.g" and post the results? This will give us some basic information needed to help further.
What exactly isn't working?
If you send M401 and M402 does the pin go in and out?
Does the pin go in and out at power up?@quinn said in BLTouch Not working Duet 2 WIfi:
; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speedThis line itself is not correct for a BLTouch. So as @Lo-Fi says revisit the config tool and choose the options for BLTouch.
-
@lo-fi I want to but the board won’t connect to my computer anymore. The port is not transferring data.
-
@phaedrux
Here is what is stated.=== Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later<LF>Board ID: 0JD0M-9P6M2-NWNS0-7J1FL-3SJ6K-T907K<LF>Used output buffers: 1 of 24 (1 max)<LF>=== RTOS ===<LF>Static ram: 25712<LF>Dynamic ram: 92704 of which 0 recycled<LF>Exception stack ram used: 256<LF>Never used ram: 12400<LF>Tasks: NETWORK(ready,1876) HEAT(blocked,1232) MAIN(running,4252) IDLE(ready,160)<LF>Owned mutexes:<LF>=== Platform ===<LF>Last reset 00:01:14 ago, cause: power up<LF>Last software reset at 2022-04-18 08:57, reason: User, spinning module GCodes, available RAM 11976 bytes (slot 3)<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms, max retries 0<LF>MCU temperature: min 19.2, current 21.6, max 21.9<LF>Supply voltage: min 1.2, current 1.5, max 1.6, under voltage events: 0, over voltage events: 0, power[Warning: Maximal number of characters per line exceeded! Check the line break settings in Terminal > Settings > Text or increase the limit in Terminal > Settings > Advanced.]
-
I have tried rebuilding the entire file. I tried a new cable and now I can connect yat to the motherboard. I have a new issue though. I can't seem to get the web control to work even rebuilding using the config tool. Any suggestions.
-
@quinn said in BLTouch Not working Duet 2 WIfi:
Duet 2 WiFi/Ethernet version 2.05.1
Ok so it looks like the board has firmware 2.05.1 on it which is quite old now. But your config file syntax is for the more recent reprapfirmware 3. Not that it would matter for your bltouch because your config has no commands related to bltouch either way.
@quinn said in BLTouch Not working Duet 2 WIfi:
I want to but the board won’t connect to my computer anymore. The port is not transferring data.
I'm not sure what you mean here. It looks like you were able to use YAT to send commands at least.
It looks like you have the board connected to the wifi network GUEST. Is that your main network? If that is a guest network and you're trying to connect to it from your computer you may not be able to reach it because routers usually keep the guest network separate.
-
My normal wifi won't let the board connect because it is 5mhz but the 2.5 I separated into a guest for other pieces of equipment in my apartment it is just named guest but it is not set up as a guest. I found my first cable did not have a proper connection so I got a new cable now it works but is requesting a restart every time I try getting it to connect. I want to update to riprap 3.3 but I cant seem to get it to work. @phaedrux
-
I can't seem to get past this error how can I fix this? @quinn
-
@quinn said in BLTouch Not working Duet 2 WIfi:
I can't seem to get past this error how can I fix this?
What error do you mean? Your image seems to show it's connected to the wifi correctly and I don't see any other errors.
@quinn said in BLTouch Not working Duet 2 WIfi:
I found my first cable did not have a proper connection so I got a new cable now it works but is requesting a restart every time I try getting it to connect.
Are you able to connect to DWC now or not? Can you show a photo of what you're seeing now?
@quinn said in BLTouch Not working Duet 2 WIfi:
I want to update to riprap 3.3 but I cant seem to get it to work.
I need more details about what is and is not working right now first. If you have access to DWC updating the firmware is pretty straightforward and involves uploading a few zip files to the system tab.
If you still have access to DWC. Upload these 4 zip files, one at a time in the system tab. Don't extract them first. Reboot after each. Use M115 in the gcode console to verify the firmware has been applied.
https://github.com/Duet3D/RepRapFirmware/releases/download/2.05.1/Duet2Firmware-2.05.1.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.3/Duet2and3Firmware-3.3.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.4.0/Duet2and3Firmware-3.4.0.zip
That will get your firmware and DWC up to date. -
undefined Phaedrux referenced this topic
