Config for the Pinda v2 ,need help!

lui2004

@t3p3tony

after i do a Dynamic test

the pinda v2 wont stop it will crash into the bed

T3P3Tony

@lui2004 if you move the probe down manually do you see the Zprobe indication on DWC change. What is it showing?

lui2004

@t3p3tony

the pinda wont trigger because i have a pei surface.

i have insert some Aluminum foil under the pei i now it will work.

which surface is good without Aluminum foil under pei ?

T3P3Tony

@lui2004 whats the PEI surface mounted on? I suppose most people using PINDA style probes an aluminium bed.

lui2004

@t3p3tony

aluminium bed with pei

this is my heightmap:

RepRapFirmware height map file v2 generated at 2021-10-12 14:59, min error -0.093, max error 0.125, mean 0.003, deviation 0.049
axis0,axis1,min0,max0,min1,max1,radius,spacing0,spacing1,num0,num1
X,Y,10.00,220.00,10.00,220.00,-1.00,20.00,20.00,11,11
      0,      0,      0,      0,      0,      0,      0,      0,      0,      0,      0
      0,      0,      0,  0.008, -0.000,  0.091,  0.057, -0.005,  0.050,  0.050,  0.007
      0,      0,      0, -0.000, -0.025,  0.082,  0.087,  0.050,  0.032,  0.091, -0.009
      0,      0,      0, -0.018,  0.025,  0.116,  0.125,  0.012,  0.007,  0.082, -0.025
      0,      0,      0, -0.025,  0.016,  0.116,  0.125, -0.018,  0.032, -0.005, -0.050
      0,      0,      0, -0.043, -0.025,  0.041,  0.025, -0.009, -0.018,  0.025, -0.084
      0,      0,      0, -0.050, -0.075, -0.034, -0.018, -0.000, -0.000, -0.000, -0.059
      0,      0,      0, -0.050, -0.038, -0.034, -0.021, -0.018, -0.018,  0.037, -0.059
      0,      0,      0, -0.055, -0.050, -0.043,  0.025, -0.018, -0.034, -0.055, -0.093
      0,      0,      0, -0.063, -0.034,  0.032,  0.025,  0.016, -0.009,  0.020, -0.050
      0,      0,      0, -0.030, -0.025,  0.007, -0.000,  0.025,  0.025,  0.050,  0.041

lui2004

I bought a new surface !

what is important to calibrate the pinda V2 ?

lui2004

This is my actuall config.g

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
 
; General preferences
G90                                      ; Send absolute coordinates...
M83                                      ; ...but relative extruder moves
 
; Network
M550 P"Ender 5"                          ; Set machine name
M552 S1                                  ; Enable network
M586 P0 S1                               ; Enable HTTP
M586 P1 S0                               ; Disable FTP
M586 P2 S0                               ; Disable Telnet
 
; Drives
M569 P0 S1                               ; Physical drive 0 goes forwards
M569 P1 S1                               ; Physical drive 1 goes forwards
M569 P2 S0                               ; Physical drive 2 goes backwards
M569 P3 S1                              ; Physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1							; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E288.30                     ; set steps per mm
M566 X600.00 Y600.00 Z60.00 E300.00                  ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z600.00 E6000.00              ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00                ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1400 I30                         ; set motor currents (mA) and motor idle factor in per cent
M84 S30       
 
 
; Axis Limits
M208 X0 Y0 Z0 S1                                     ; set axis minima
M208 X235 Y235 Z250 S0                               ; set axis maxima
 
; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 									   ; configure Z-probe endstop for low end on Z
 
;Filament Sensors
M591 D0 P2 C"!e0_stop" S1   			   ;Extruder 1(0)
 
 

; PINDA2
;M558 P5 C"^zprobe.in" H1.5 F1000 T12000 A3 ; set Z probe to PINDA2
M558 K0 P8 C"^zprobe.in" I1 H2 F1000 T6000 A20 S0.005 ; set Z probe type to effector and the dive height + speeds, max number of probes per point, tolerance(MM)
M308 S2 P"e1temp" A"Pinda V2" Y"thermistor" T100000 B3950 ; temperature of PINDA2
G31 P500 X52.7 Y18 Z1.775                  ; set Z probe trigger value, offset and trigger height
M557 X10:210 Y10:210 S20                       ; define mesh grid
;M557 X41.2:219 Y15:195 S20
;M671 X28.8:198.8:198:28.8 Y24:24:194:194 P0.5
M557 X10:220 Y10:220 S20
 
 
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 								   ; set temperature limit for heater 1 to 300C
M307 H1 B0 S1.00           
 
; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on
 
; Tools
M563 P0 D0 H1                            ; Define tool 0 S3D
G10 P0 X0 Y0 Z0                          ; Set tool 0 axis offsets
G10 P0 R0 S0                             ; Set initial tool 0 active and standby temperatures to 0C
 
; Automatic saving after power loss is not enabled
 
; Custom settings are not configured
M575 P1 S1 B57600 ; enable support for PanelDue
M572 D0 S0.05 ; Pressure Advance PLA
;M572 D0 S0.08 ; Pressure Advance PLA
M207 S1.50 R0 F2100 T2100 Z0 ; Firmware Retraction P0 S0.45 R0 F2100 T2100 Z0 ; Firmware Retraction
M204 P500 T2000
T0 ; Sets Tool0 as default

M501

homeall.g

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Jul 28 2020 08:52:12 GMT+0200 (Mitteleuropäische Sommerzeit)
G91 ; relative mode
G1 H2 Z4 F200 ; raise head 4mm
G1 H1 X-240 Y-240 F3000 ; move up to 240mm in the -X and -Y directions until the homing switches are triggered
G1 H2 X4 Y4 F600; move slowly 6mm in +X and +Y directions
G1 H1 X-10 Y-10 ; move up to 10mm in the -X and -Y directions until the homing switches are triggered
G90 ; back to absolute mode
G1 X57.3 Y92 F2000 ; put head over the centre of the bed, or wherever you want to probe
G30 ; lower head, stop when probe triggered and set Z to trigger height

; homex.g

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91 ; relative mode
G1 H2 Z4 F200 ; raise head to avoid dragging nozzle over the bed
G1 H1 X-240 F3000 ; move up to 240mm in the +X direction, stopping if the homing switch is triggered
G1 X-4 F600 ; move slowly 4mm in the -X direction
G1 H1 X10 ; move slowly 10mm in the +X direction, stopping at the homing switch
G1 H2 Z-4 F200 ; lower the head again
G90 ; back to absolute mode

homey.g

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91 ; relative mode
G1 H2 Z4 F200 ; raise head to avoid dragging nozzle over the bed
G1 H1 Y-240 F3000 ; move up to 240mm in the -X direction, stopping if the homing switch is triggered
G1 X4 F600 ; move slowly 4mm in the +X direction
G1 H1 X-10 ; move slowly 10mm in the -X direction, stopping at the homing switch
G1 H2 Z-4 F200 ; lower the head again
G90 ; back to absolute mode

homez.g

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Jul 28 2020 08:52:37 GMT+0200 (Mitteleuropäische Sommerzeit)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G90               ; absolute positioning
G1 X57.3 Y92 F6000 ; go to first probe point
G30               ; home Z by probing the bed

thanks for help

lui2004

Hi

Is there a how to ,to set z offset on different temperature? Like in marlin?

T3P3Tony

@lui2004 there is not the option of using a table like i think Marlin has. You configure the S and C parameters within G31 to compensate:
https://duet3d.dozuki.com/Wiki/G31

Based on this thread:
https://forum.duet3d.com/topic/16972/pinda-2-probe-with-temperature-compensation/5?_=1593546022132

It appears the non linearity of the measurements at different temperatures could be a problem.

The poster in that post shows a conditional gcode way to get around the problem. Before you do that it would be worth testing you can get a good z probe performance with everything (including the PINDA temperature) at a steady temperature.

Once thats working then non linear temperature compensation can be looked at,

lui2004

@t3p3tony

Thanks ,i will give it a try!

Other question when print is finished my z axis at 0 what i can do that the z-axis goes u after print?

T3P3Tony

@lui2004 in the end gcode you can add a move to lift slightly and move the tool out the way.

E,g,

G91 ; set to relative positioning
G1 Z5 ; raise Z 5 mm
G90 ; set to absolute positioning
G1 X0 Y0 ; park at X0 Y0