Auto Tool Height Measurement

Terry

Just found G38.2, which appears to be more suitable.

After testing with

M558 K1 P8 C"!1.io2.in" F1000
G38.2 V1 P1

I get the same problem! There appears to be a bug where the machine and user positions are always updated to be equal to the requested destination move, even though the move was interrupted by an endstop or probe trigger.

fcwilt

@Terry said in Auto Tool Height Measurement:

Just found G38.2, which appears to be more suitable.

After testing with
M558 K1 P8 C"!1.io2.in" F1000
G38.2 V1 P1
I get the same problem! There appears to be a bug where the machine and user positions are always updated to be equal to the requested destination move, even though the move was interrupted by an endstop or probe trigger.

Perhaps so - because it did not happen in my testing - and the "home" position (which for my testing was 0) remained unchanged.

I know that 3.2.0 had a bug which prevented my 3 Z stepper printer (each stepper had its own end stop) from homing.

Frederick

Terry

Same bug is present on 3.2.2

fcwilt

@Terry said in Auto Tool Height Measurement:

Same bug is present on 3.2.2

I wonder why you are seeing that and I'm not.

What do your end stop configuration look like for the normal axis end stop and this switch end stop.

Thanks.

Frederick

Terry

Axis setup is:

M569 P1.1 S0
M584 V1.1
M208 V0:100
M92 V400
M350 V16 I1	
M566 V400
M203 V10000
M201 V6000
M906 V1500
M574 V2 S1 P"1.io1.in"

Test macro is:

M558 K1 P8 C"!1.io2.in" F1000
G38.2 V1 P1

M117 {move.axes[4].userPosition}

fcwilt

@Terry said in Auto Tool Height Measurement:

Axis setup is:

M569 P1.1 S0
M584 V1.1
M208 V0:100
M92 V400
M350 V16 I1	
M566 V400
M203 V10000
M201 V6000
M906 V1500
M574 V2 S1 P"1.io1.in"

Test macro is:

M558 K1 P8 C"!1.io2.in" F1000
G38.2 V1 P1

M117 {move.axes[4].userPosition}

I will have to test using a probe.

Why are you echoing the userPosition instead of the machinePosition?

Frederick

Terry

Just as a legacy of testing that machinePosition and userPosition were the same, which they are in this instance.

fcwilt

To test G1 H4 I created the following macros:

Macro to configure for normal Z end stop:

M574 Z1 S1 P"nil"
M574 Z1 S1 P"io3.in"

Macro to configure for temporary Z end stop:

M574 Z1 S1 P"nil"
M574 Z1 S1 P"^!io4.in"

Macro to test G1 H4

G90
G1 Z100 F600
echo "POST G90 G1 Z100 F600: machinePosition = " ^ move.axes[2].machinePosition ^ " === userPosition = " ^ move.axes[2].userPosition 
G60 S0
G91
G1 H4 Z50 F300
echo "POST G91 G1 H4 Z50 F300: machinePosition = " ^ move.axes[2].machinePosition ^ " === userPosition = " ^ move.axes[2].userPosition 
G90
G1 R0 Z0
echo "POST G90 G1 R0 Z0: machinePosition = " ^ move.axes[2].machinePosition ^ " === userPosition = " ^ move.axes[2].userPosition

I ran the macro to configure for the temporary Z end stop
I ran the macro to test G1 H4
I waited a bit and triggered the temporary Z end stop
I ran the macro to configure for the normal Z end stop

Here are the echo outputs:

POST G90 G1 Z100 F600: machinePosition = 100.000 === userPosition = 100.000

POST G91 G1 H4 Z50 F300: machinePosition = 129.786 === userPosition = 129.786

POST G90 G1 R0 Z0: machinePosition = 129.786 === userPosition = 100.000

The homed status of Z was not changed.

Frederick

Terry

Good, that seems to confirm that it's an issue with the 3HC firmware.

jlipavsky79

did this ever get resolved? looking to do the exact same thing.....

Dougal1957

it may be worth looking into
https://jubilee3d.com/index.php?title=ZTATP