DWC 3.1.1
-
)1)non posso dare nessun comando .
quando estraggo il file zip dopo aver cancellato tutto ,non compare file dwc.json erore solito e' nessuna applicazione e concesso di usare la porta.)2) se estraggo il file zip previa svuotamento www rimane la versione precedente
-
)2) se estraggo il file zip senza svuotamento www rimane la versione precedente
-
posso fare m122 versione senza dwc3.1.1
-
lo ripete ciclo for nest una chiamata indirizzo diverso dall'attuale . scusatemi -
difetti scheda improbabile
difetto ssd comprata nuova ieri pari alla vecchia
mi rimane la procedura ma identica alla vostra consigliata
problemi sistema operativo ,preciso originale .
chiedo aiuto se avete un caso analogo. grazie sempre gentilissimi -
When connected to USB terminal, send M122 and share the results here so we can see what it says about the SD card.
-
PRIMA DELL AGGIORNAMENTO
M122
=== Diagnostics ===RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F23T0-6JTD0-3S46T-TGA0F
Used output buffers: 3 of 24 (16 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 72904 of which 0 recycled
Never used RAM 15716, free system stack 189 words
Tasks: NETWORK(ready,221) HEAT(blocked,309) MAIN(running,452) IDLE(ready,19)
Owned mutexes: WiFi(NETWORK) HTTP(MAIN)
=== Platform ===
Last reset 00:02:07 ago, cause: power up
Last software reset at 2021-02-17 13:39, reason: User, GCodes spinning, available RAM 15680, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 71,71,71
MCU temperature: min 32.1, current 35.6, max 36.0
Supply voltage: min 11.3, current 11.4, max 11.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 62571, standstill, SG min/max not available
Driver 1: position 62571, standstill, SG min/max not available
Driver 2: position 62571, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-03-11 20:14:51
Cache data hit count 156303538
Slowest loop: 7.39ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.7ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is ready with "M122 " in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 29.58ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address 84:0d:8e:b3:ae:3e
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24912
WiFi IP address 192.168.178.105
WiFi signal strength -74dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 2 0 0 0 0 0 0
- WiFi -
-
DOPO AGGIORNAMENTO
20:18:53M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F23T0-6JTD0-3S46T-TGA0F
Used output buffers: 7 of 24 (10 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 72904 of which 0 recycled
Never used RAM 15716, free system stack 199 words
Tasks: NETWORK(ready,245) HEAT(blocked,307) MAIN(running,466) IDLE(ready,19)
Owned mutexes: WiFi(NETWORK) HTTP(MAIN)
=== Platform ===
Last reset 00:00:23 ago, cause: power up
Last software reset at 2021-02-17 13:39, reason: User, GCodes spinning, available RAM 15680, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 18,18,18
MCU temperature: min 32.0, current 35.1, max 35.5
Supply voltage: min 11.3, current 11.4, max 11.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 62571, standstill, SG min/max not available
Driver 1: position 62571, standstill, SG min/max not available
Driver 2: position 62571, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-03-11 20:18:50
Cache data hit count 27845843
Slowest loop: 14.50ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 0.9ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is ready with "M122 " in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 28.05ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address 84:0d:8e:b3:ae:3e
WiFi Vcc 3.42, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25680
WiFi IP address 192.168.178.105
WiFi signal strength -74dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 4 4 0 0 0 0 0 0
- WiFi -
-
E' UTILE PER CAPIRE?
-
@luca-Massimiliano ECCO NON HA AGGIORNATO LA WWW E' STATA ESPLOSA -
What URL are you using to reach the web interface?
Try connecting to just the bare IP address.
-
We're sorry but Duet Web Control does not work properly without JavaScript enabled. Please enable it to continue.
-
NON DOVREBBE FUNZIONARE? CON JAVA FUNZIONA
-
-
ORA OK , MANCA IL SECONDO RISCALDATORE , SONO NOMINITA 0 E 1 ANCHE REPETIER LI NOMINA COSI' E NON SETE LA TEMPERATURA DEL PRIMO RISCALDATORE . HO RISOLTO GRAZIE A TE LA VERSIONE TE NE SONO GRATO MA NON CAPISCO PERCHE' FUNZIONA SOLO CON JAVA.
1 IL PRIMO RISCALDATORE ASSENE
2 PERCHE' JAVA ? -
-
-
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M308 S2 P"e1temp" Y"thermistor" T100000 B4388 ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S280 ; set temperature limit for heater 2 to 280C -
Post the full contents of your config.g
Java is required for it to work. That's just the way it's made.
-
SCUSA AMICO , NON HO CAPITO COSA DEVO FARE
