X and Y axis moves instead of Extuder

AlVo94

Hello together,

i`m a new Duet/Reprap User and new to this forum. I´m currently facing a strange problem: if i want to extrude filament my x and y axis moves (corexy machine) and not the extruder-stepper. Anythin else works fine. I´m sure that there is a super simple solution for my problem but after reading anything i found in the wiki and in this forum i wasn´t able to find it.
Here is my config.g:

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Fri Feb 12 2021 12:56:13 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"My Printer"                             ; set printer name
M669 K1                                        ; select CoreXY mode

; Network
M551 P                          ; set password
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S0                                     ; physical drive 0 goes backwards
M569 P1 S0                                     ; physical drive 1 goes backwards
M569 P2 S0                                     ; physical drive 2 goes backwards
M569 P3 S0                                     ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                           		; set drive mapping

M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z634,5 E387,37.00              ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E1000 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X430 Y430 Z450 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; Set endstops controlled by probe

; Z-Probe
M950 S0 C"exp.heater3"                         ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000            ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X36.8 Y-6.2 Z1.580                      ; set Z probe trigger value, offset and trigger height
M557 X40:430 Y0:430 S40                         ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; enable PID mode for the bed heater
M307 H0 R1.084 C389.8 D4.34 S0.70 V12.2
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                   ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"Volcano" D0 H1 F0                    ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
; dual Z motors
M584 X0 Y1 Z2:4 E                              ; two Z motors connected to driver outputs Z and E1
M671 X-20:520 Y2150:215 S0.5                   ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
M208 X0:430 Y0:430                            ; X carriage moves from -5 to 205, Y bed goes from 0 to 

; Miscellaneous
M575 P1 S1 B57600                              ; enable support for PanelDue
M501                                           ; load saved parameters from non-volatile memory

Thank you for your help.
With kind regards
Alex

Rushmere3D

Hi,

First you have two M584 commands in you're config.g.

M584 X0 Y1 Z2 E3

M584 X0 Y1 Z2:4 E

You also have (,) in you're M92 command.

M92 X80.00 Y80.00 Z634,5 E387,37.00

These need to be (.).

AlVo94

@Rushmere3D
thank´s that solved my problem. Sry for bothering you.

Rushmere3D

@AlVo94

No problem at all, glad you're up and running.