RRF3.2 upgrade help
-
Post your homing files.
Post the results of M122 and M98 P"config.g"
Did you generate a fresh config set using the web tool?
https://configtool.reprapfirmware.org/Start
If you did, did you also take the entire package including the homing files etc?
-
I didn't use the tool directly, as I could work out how to get 2 motors on the extruder and 3 on the z etc. But I made a basic setup and copied the changes.
; homex.g
; called to home the X axisG91 ; use relative positioning
G1 H2 X0.5 Y-0.5 F10000 ; energise
M400 ; make sure everything has stopped before we make changes
G4 P100 ; wait 400ms;M913 X25 Y25 ; drop motor currents to 50%
M915 H200 X Y S10 R0 F0 ; set X and Y to sensitivity 10, do nothing when stall, unfilteredG1 H2 Z3 F5000 ; lift Z 3mm
G1 H1 X1 F3000 ; move right 1mm, stopping at the endstop
G4 P100 ; wait 100ms
G1 H1 X-500 F3000 ; move left 400mm, stopping at the endstop
G1 H1 X2 F2000 ; move away from end
G1 H2 Z-3 F1200 ; lower Z
G90 ; back to absolute positioningM400 ; make sure everything has stopped before we reset the motor currents
G4 P100 ; wait 400ms
;M913 X100 Y100 ; motor currents back to 100%
M574 X1 S0 ; Define active low and unused microswitches -
; homey.g
; called to home the Y axisG91 ; use relative positioning
G1 H2 X0.5 Y-0.5 F10000 ; energise
M400 ; make sure everything has stopped before we make changes
M913 X75 Y75 ; drop motor currents to 75%
M915 H200 X Y S7 R0 F0 ; set X and Y to sensitivity 7, do nothing when stall, unfilteredG1 H2 Z3 F5000 ; lift Z 3mm
G1 H1 Y1 F2000 ; move away from end
G1 H1 Y-500 F3000 ; move to the front 400mm, stopping at the endstop
G1 H1 Y2 F2000 ; move away from end
G1 H2 Z-3 F1200 ; lower Z
G90 ; back to absolute positioningM400 ; make sure everything has stopped before we reset the motor currents
G4 P100 ; wait 400ms
M913 X100 Y100 ; motor currents back to 100%M574 X1 S0 ; Define active low and unused microswitches
M915 H200 X Y S3 R3 F0 ; set X and Y to sensitivity 3, Rehome when stall, unfiltered -
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool on Mon Jan 01 2018 19:47:24 GMT+0000 (GMT Standard Time)
G90 ; relative positioning
G1 Z5 F6000 ; lift Z relative to current position
G90 ; absolute positioning
G1 X40 Y40 F6000 ; go to first probe point
G30 ; home Z by probing the bed; Uncomment the following lines to lift Z after probing
G91 ; relative positioning
G1 Z5 F100 ; lift Z relative to current position
G90 ; absolute positioning -
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.0 or 1.01 + DueX5
Board ID: 08DAM-999TL-MQ4S4-6JKDJ-3SD6K-1QGBZ
Used output buffers: 3 of 24 (12 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73716 of which 0 recycled
Never used RAM 14904, free system stack 191 words
Tasks: NETWORK(ready,175) HEAT(blocked,323) DUEX(blocked,35) MAIN(running,548) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:01:27 ago, cause: software
Last software reset at 2021-01-29 06:57, reason: User, GCodes spinning, available RAM 14904, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 17.7, current 18.2, max 19.0
Supply voltage: min 24.3, current 24.4, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0, standstill, SG min/max not available
Driver 6: position 0, standstill, SG min/max not available
Driver 7: position 0, standstill, SG min/max not available
Driver 8: position 0, standstill, SG min/max not available
Driver 9: position 0, standstill, SG min/max not available
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-29 06:58:33
Cache data hit count 107583709
Slowest loop: 11.37ms; fastest: 0.20ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 288.93ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address 5c:cf:7f:2c:27:7e
WiFi Vcc 3.37, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24640
WiFi IP address 192.168.86.66
WiFi signal strength -55dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
=== DueX ===
Read count 1, 0.68 reads/min
- WiFi -
-
1/29/2021, 6:59:04 AM M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: Unknown sensor type name "max31865"
Warning: Sensor number 1 has not been defined
Error: Sensor number out of range
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 530C
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 530C
Error: Heater 2 not found
Error: Heater 3 not found
Error: Heater 4 not found
Error: Heater 5 not found
Error: Heater 6 not found
Error: Heater 7 not found -
Sorry for the spam! It just looked clearer to me
Many thanks
-
OK, I have fixed the temperatures not showing. It seems a couple of typos on my behalf
-
aha, it seems the macros were causing the issue, all fixed
-
So you've got it all working now?