Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    cannot get 3hc to connect.

    Firmware installation
    5
    30
    1.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • bamundefined
      bam
      last edited by

      m122
      === Diagnostics ===
      RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
      Board ID: 08DJM-956BA-NA3TJ-6JTD2-3SN6K-9BAQU
      Used output buffers: 1 of 40 (14 max)
      === RTOS ===
      Static ram: 154604
      Dynamic ram: 162320 of which 100 recycled
      Exception stack ram used: 272
      Never used ram: 75920
      Tasks: NETWORK(ready,1968) HEAT(blocked,476) CanReceiv(suspended,3820) CanSender(suspended,1488) CanClock(blocked,1436) TMC(blocked,192) MAIN(running,5056) IDLE(ready,76)
      Owned mutexes:
      === Platform ===
      Last reset 00:06:53 ago, cause: software
      Last software reset details not available
      Error status: 0
      MCU temperature: min 43.7, current 44.6, max 44.8
      Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
      12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
      Driver 0: standstill, reads 6854, writes 14 timeouts 0, SG min/max 0/0
      Driver 1: standstill, reads 6855, writes 14 timeouts 0, SG min/max 0/0
      Driver 2: standstill, reads 6855, writes 14 timeouts 0, SG min/max 0/0
      Driver 3: standstill, reads 6858, writes 11 timeouts 0, SG min/max 0/0
      Driver 4: standstill, reads 6856, writes 14 timeouts 0, SG min/max 0/0
      Driver 5: standstill, reads 6856, writes 14 timeouts 0, SG min/max 0/0
      Date/time: 2021-01-01 23:45:44
      Slowest loop: 2102.42ms; fastest: 0.14ms
      === Storage ===
      Free file entries: 10
      SD card 0 not detected, interface speed: 37.5MBytes/sec
      SD card longest read time 0.0ms, write time 0.0ms, max retries 0
      === Move ===
      Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
      Bed compensation in use: none, comp offset 0.000
      === MainDDARing ===
      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
      === AuxDDARing ===
      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
      === Heat ===
      Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP* is ready with "M122" in state(s) 0
      Telnet is idle in state(s) 0
      File is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is idle in state(s) 0
      Trigger* is idle in state(s) 0
      Queue is idle in state(s) 0
      LCD is idle in state(s) 0
      SBC is idle in state(s) 0
      Daemon* is idle in state(s) 0
      Aux2 is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty.
      === Network ===
      Slowest loop: 0.81ms; fastest: 0.01ms
      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
      HTTP sessions: 0 of 8

      • Ethernet -
        State: disabled
        Error counts: 0 0 0 0 0
        Socket states: 0 0 0 0 0 0 0 0
        === CAN ===
        Messages sent 1636, longest wait 0ms for type 0
        === Linux interface ===
        State: 0, failed transfers: 7
        Last transfer: 17ms ago
        RX/TX seq numbers: 46099/13071
        SPI underruns 7, overruns 7
        Number of disconnects: 0
        Buffer RX/TX: 0/0-0
        === Duet Control Server ===
        Duet Control Server v3.1.1
        Code buffer space: 4096
        Configured SPI speed: 8000000 Hz
        Full transfers per second: 1.17
        1/1/2021, 11:45:04 PM m115
        FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet 3 MB6HC v1.01 or later FIRMWARE_DATE: 2020-05-19b2
      1 Reply Last reply Reply Quote 0
      • bamundefined
        bam @dc42
        last edited by

        @dc42 what does this mean?

        M32 "0:/gcodes/Duet3Firmware_EXP3HC.bin"
        Error: Unterminated string in line 3

        Vetiundefined 1 Reply Last reply Reply Quote 0
        • bamundefined
          bam @dc42
          last edited by

          @dc42 and now this

          Warning: Incompatible firmware, please upgrade as soon as possible

          1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti @bam
            last edited by

            @bam said in cannot get 3hc to connect.:

            M32 "0:/gcodes/Duet3Firmware_EXP3HC.bin"

            M32 is start a print.

            you want to print a firmware binary file?

            and why is that file in the gcodes folder?

            bamundefined 2 Replies Last reply Reply Quote 1
            • bamundefined
              bam @Veti
              last edited by

              @Veti I Got It!!! 🙂 Finally!!

              m122 b1
              Diagnostics for board 1:
              Duet EXP3HC firmware version 3.2-RC2 (2020-12-24)
              Bootloader ID: not available
              Never used RAM 154536, free system stack 200 words
              HEAT 75 CanAsync 94 CanRecv 87 TMC 64 MAIN 173 AIN 257
              Last reset 00:00:35 ago, cause: software
              Last software reset data not available
              Driver 0: position 0, 100.0 steps/mm, standstill, reads 63861, writes 16 timeouts 0, SG min/max 0/0
              Driver 1: position 0, 100.0 steps/mm, standstill, reads 63863, writes 16 timeouts 0, SG min/max 0/0
              Driver 2: position 0, 80.0 steps/mm, standstill, reads 63871, writes 11 timeouts 0, SG min/max 0/0
              Moves scheduled 0, completed 0, in progress 0, hiccups 0
              No step interrupt scheduled
              VIN: 24.1V, V12: 12.2V
              MCU temperature: min 45.9C, current 46.1C, max 46.1C
              Ticks since heat task active 73, ADC conversions started 35564, completed 35564, timed out 0
              Last sensors broadcast 0x00000006 found 2 76 ticks ago, loop time 0
              CAN messages queued 243, send timeouts 0, received 252, lost 0, free buffers 36
              1/2/2021, 1:13:10 AM m122
              === Diagnostics ===
              RepRapFirmware for Duet 3 MB6HC version 3.2-RC2 running on Duet 3 MB6HC v1.01 or later (SBC mode)
              Board ID: 08DJM-956BA-NA3TJ-6JTD2-3SN6K-9BAQU
              Used output buffers: 1 of 40 (13 max)
              === RTOS ===
              Static ram: 149788
              Dynamic ram: 62676 of which 136 recycled
              Never used RAM 146232, free system stack 200 words
              Tasks: Linux(ready,119) HEAT(blocked,188) CanReceiv(blocked,836) CanSender(blocked,371) CanClock(blocked,360) TMC(blocked,53) MAIN(running,1217) IDLE(ready,19)
              Owned mutexes: HTTP(MAIN)
              === Platform ===
              Last reset 00:00:15 ago, cause: software
              Last software reset time unknown, reason: StuckInSpinLoop, GCodes spinning, available RAM 147880, slot 1
              Software reset code 0x0083 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0040080f BFAR 0x00000000 SP 0x204334e4 Task Linu Freestk 443 ok
              Stack: 00429a2d 00429ab0 61000000 a5a5a5a5 a5a5a5a5 a5a5a5a5 00000000 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5
              Error status: 0x00
              Aux0 errors 0,0,0
              Aux1 errors 0,0,0
              MCU temperature: min 43.8, current 46.0, max 46.1
              Supply voltage: min 24.0, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
              12V rail voltage: min 12.2, current 12.2, max 12.3, under voltage events: 0
              Driver 0: position 0, standstill, reads 23487, writes 14 timeouts 0, SG min/max 0/0
              Driver 1: position 0, standstill, reads 23487, writes 14 timeouts 0, SG min/max 0/0
              Driver 2: position 0, standstill, reads 23487, writes 14 timeouts 0, SG min/max 0/0
              Driver 3: position 0, standstill, reads 23491, writes 11 timeouts 0, SG min/max 0/0
              Driver 4: position 0, standstill, reads 23488, writes 14 timeouts 0, SG min/max 0/0
              Driver 5: position 0, standstill, reads 23488, writes 14 timeouts 0, SG min/max 0/0
              Date/time: 2021-01-02 01:13:08
              Slowest loop: 0.45ms; fastest: 0.05ms
              === Storage ===
              Free file entries: 10
              SD card 0 not detected, interface speed: 37.5MBytes/sec
              SD card longest read time 0.0ms, write time 0.0ms, max retries 0
              === Move ===
              DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
              === MainDDARing ===
              Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
              === AuxDDARing ===
              Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
              === Heat ===
              Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
              === GCodes ===
              Segments left: 0
              Movement lock held by null
              HTTP* is doing "M122" in state(s) 0
              Telnet is idle in state(s) 0
              File is idle in state(s) 0
              USB is idle in state(s) 0
              Aux is idle in state(s) 0
              Trigger* is idle in state(s) 0
              Queue is idle in state(s) 0
              LCD is idle in state(s) 0
              SBC is idle in state(s) 0
              Daemon is idle in state(s) 0
              Aux2 is idle in state(s) 0
              Autopause is idle in state(s) 0
              Code queue is empty.
              === CAN ===
              Messages queued 55, send timeouts 0, received 95, lost 0, longest wait 1ms for reply type 6018, free buffers 48
              === SBC interface ===
              State: 4, failed transfers: 0
              Last transfer: 2ms ago
              RX/TX seq numbers: 442/442
              SPI underruns 0, overruns 0
              Number of disconnects: 0, IAP RAM available 0x2c8a8
              Buffer RX/TX: 0/0-0
              === Duet Control Server ===
              Duet Control Server v3.2.0-rc2
              Code buffer space: 4096
              Configured SPI speed: 8000000 Hz
              Full transfers per second: 35.67
              Maximum length of RX/TX data transfers: 5196/900

              1 Reply Last reply Reply Quote 0
              • bamundefined
                bam @Veti
                last edited by

                @Veti i dont know why the file is in there, not sure how to delete either. mightve shown up with the .bin i downloaded.

                this whole time ive just been trying to get the boards online and the software updated. I can config the printer later.

                twisted pair wasnt actually twisted. just looked twisted.

                Phaedruxundefined 1 Reply Last reply Reply Quote 0
                • Phaedruxundefined
                  Phaedrux Moderator @bam
                  last edited by

                  @bam said in cannot get 3hc to connect.:

                  not sure how to delete

                  Either right click and delete, or if that won't work, you can try and do it from the SBC side. The first SD card (0:/) is emulated by DCS and its default directory is /opt/dsf/sd

                  Z-Bot CoreXY Build | Thingiverse Profile

                  bamundefined 1 Reply Last reply Reply Quote 0
                  • bamundefined
                    bam @Phaedrux
                    last edited by

                    @Phaedrux 2021-01-02-012341_1024x768_scrot.png yeah theres nothing here so idk

                    1 Reply Last reply Reply Quote 0
                    • Vetiundefined
                      Veti
                      last edited by

                      you are editing a file called gcodes.g

                      nothing phaedrux said mentioned any of that.

                      bamundefined 1 Reply Last reply Reply Quote 0
                      • bamundefined
                        bam
                        last edited by bam

                        thanks for all the helps @dc42 @Veti @Phaedrux @bearer i promise you i will be back. have to make a hardware store run to find an (actual) twisted pair, not this spliced mess, and then start wiring motors and sensors.80B0B486-E3DE-4305-8A35-91BD1102EE6B.jpeg

                        1 Reply Last reply Reply Quote 0
                        • bamundefined
                          bam @Veti
                          last edited by

                          @Veti

                          Either right click and delete, or if that won't work, you can try and do it from the SBC side.

                          i did it from the duet3webcontrol.

                          sorry if i dont know anything about these and i jumped in feet first.

                          1 Reply Last reply Reply Quote 0
                          • Vetiundefined
                            Veti
                            last edited by

                            go to the macros tab in dwc.

                            find the file Duet3Firmware_EXP3HC.bin and right click on it.

                            a dropdown menu should appear where you can select delete

                            1 Reply Last reply Reply Quote 0
                            • First post
                              Last post
                            Unless otherwise noted, all forum content is licensed under CC-BY-SA