Forward/redefine tools T0 & T1.
-
My T0 tool defined to "Heated Bed",
and T1 tool to "Extruder".Can they be reassigned without a "configurator"?
(T0 - Extruder & T1 - Heated Bed)Unfortunately, I haven't found HOW to do this, and I'm afraid to ruin something.
Here is my config file:
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon Aug 06 2018 00:13:45 GMT+0100 (IST); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmare;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R105.6 L288 B105 H250 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them; Network
M550 PMy printer ; Set machine name
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M350 X16 Y16 Z16 I1 ; Configure microstepping with interpolation
M350 E8 I0 ; Configure E axis microstepping to x8 with interpolation OFF
M92 X80 Y80 Z80 E2098 ; Set steps per mm
M566 P1 X240 Y240 Z240 E6 ; Set maximum instantaneous speed changes (mm/min)(Jerk)
M203 X12000 Y12000 Z12000 E2400 ; Set maximum speeds (mm/min)
M201 X660 Y660 Z660 E120 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E400 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 Z0 S1 ; Set minimum Z; Endstops
M574 X2 Y2 Z2 S1 ; Set active high endstops; Z-Probe
M558 P5 R0.4 H2 F1200 T6000 ; Set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height
M557 R90 S20 ; Define mesh grid; Heaters
M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M307 P0 A191.5 C1032.9 D5.1 ; CALIBRATION my
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X200 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 I0 F35 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P1 D0 H1 F2 ; Define tool 0 + DEFAULT Fan0 ->forwarded to-> Fan2!!!
G10 P1 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P1 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Automatic saving after power loss is not enabled
; Custom settings are not configured
; Miscellaneous
T1 ; Select first tool
M501 ; new commands override the ones earlier in your config.g -
@vapvap said in Forward/redefine tools T0 & T1.:
; Tools
M563 P1 D0 H1 F2 ; Define tool 0 + DEFAULT Fan0 ->forwarded to-> Fan2!!!
G10 P1 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P1 R0 S0 ; Set initial tool 0 active and standby temperatures to 0CAll the P1 in there should be P0
@vapvap said in Forward/redefine tools T0 & T1.:
T1 ; Select first tool
And that should be T0
Heater0 should be the bed heater
Heater1 should be your tool0 heater
-
Thank you so much, now everything works as it should!
Honestly, the help and support of key figures like you makes this forum one of the best in 3D printing!
Please stay with us! )
