Duet freezing
-
Sometimes my delta with a build size of 1m x 1,5m freeze without any logical reason, at least for me
Maybe this is the reason, but what does this mean ??
Last software reset at 2020-06-04 16:50, reason: User, spinning module GCodes, available RAM 11400 bytes (slot 2) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414dBelow the full diagnostic after reboot:
24/9/2020, 14:14:23: Connected to 192.168.1.206 24/9/2020, 14:15:38: M122: === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet WiFi 1.02 or later Board ID: 08DDM-9FAM2-LW4S4-6J9DG-3SD6N-13SRX Used output buffers: 3 of 24 (6 max) === RTOS === Static ram: 25712 Dynamic ram: 92700 of which 300 recycled Exception stack ram used: 440 Never used ram: 11920 Tasks: NETWORK(ready,764) HEAT(blocked,1232) MAIN(running,3640) IDLE(ready,160) Owned mutexes: === Platform === Last reset 00:05:22 ago, cause: power up Last software reset at 2020-06-04 16:50, reason: User, spinning module GCodes, available RAM 11400 bytes (slot 2) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 0.0ms, max retries 0 MCU temperature: min 30.9, current 33.9, max 35.5 Supply voltage: min 24.0, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max 359/699 Driver 1: standstill, SG min/max 408/712 Driver 2: standstill, SG min/max 41/179 Driver 3: standstill, SG min/max not available Driver 4: standstill, SG min/max not available Date/time: 2020-09-24 14:15:37 Cache data hit count 902642629 Slowest loop: 26.07ms; fastest: 0.07ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0, FreeDm: 160, MinFreeDm: 154, MaxWait: 14074ms Bed compensation in use: mesh, comp offset 0.000 === DDARing === Scheduled moves: 5, completed moves: 5, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 === GCodes === Segments left: 0 Stack records: 1 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 15.47ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address 60:01:94:73:5b:3c WiFi Vcc 3.39, reset reason Turned on by main processor WiFi flash size 4194304, free heap 24952 WiFi IP address 192.168.1.206 WiFi signal strength -65dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: no data received 24/9/2020, 14:15:58: M122: === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet WiFi 1.02 or later Board ID: 08DDM-9FAM2-LW4S4-6J9DG-3SD6N-13SRX Used output buffers: 3 of 24 (12 max) === RTOS === Static ram: 25712 Dynamic ram: 92744 of which 256 recycled Exception stack ram used: 440 Never used ram: 11920 Tasks: NETWORK(ready,764) HEAT(blocked,1232) MAIN(running,3640) IDLE(ready,160) Owned mutexes: === Platform === Last reset 00:05:41 ago, cause: power up Last software reset at 2020-06-04 16:50, reason: User, spinning module GCodes, available RAM 11400 bytes (slot 2) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 146.5ms, max retries 0 MCU temperature: min 33.8, current 34.1, max 34.4 Supply voltage: min 24.2, current 24.4, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: standstill, SG min/max not available Date/time: 2020-09-24 14:15:57Cache data hit count 960253407 Slowest loop: 80.23ms; fastest: 0.08ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms Bed compensation in use: mesh, comp offset 0.000 === DDARing === Scheduled moves: 5, completed moves: 5, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 === GCodes === Segments left: 0 Stack records: 1 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 364.48ms; fastest: 0.08ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 1 WiFi firmware version 1.23 WiFi MAC address 60:01:94:73:5b:3c WiFi Vcc 3.39, reset reason Turned on by main processor WiFi flash size 4194304, free heap 25064 WiFi IP address 192.168.1.206 WiFi signal strength -65dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: no data received 24/9/2020, 14:17:51: M122: === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet WiFi 1.02 or later Board ID: 08DDM-9FAM2-LW4S4-6J9DG-3SD6N-13SRX Used output buffers: 1 of 24 (15 max) === RTOS === Static ram: 25712 Dynamic ram: 92744 of which 256 recycled Exception stack ram used: 440 Never used ram: 11920 Tasks: NETWORK(ready,764) HEAT(blocked,1232) MAIN(running,3640)IDLE(ready,160) Owned mutexes: === Platform === Last reset 00:07:35 ago, cause: power up Last software reset at 2020-06-04 16:50, reason: User, spinning module GCodes, available RAM 11400 bytes (slot 2) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 0.0ms, max retries 0 MCU temperature: min 33.7, current 33.9, max 34.2 Supply voltage: min 24.1, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max not available Driver 1: standstill, SG min/max not available Driver 2: standstill, SG min/max not available Driver 3: standstill, SG min/max not available Driver 4: standstill, SG min/max not available Date/time: 2020-09-24 14:17:50 Cache data hit count 1294237665 Slowest loop: 4.94ms; fastest: 0.08ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms Bed compensation in use: mesh, comp offset 0.000 === DDARing === Scheduled moves: 5, completed moves: 5, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 === GCodes === Segments left: 0 Stack records: 1 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is idle in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 203.13ms; fastest: 0.08ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access pointFailed messages: pending 0, notready 0, noresp 3 WiFi firmware version 1.23 WiFi MAC address 60:01:94:73:5b:3c WiFi Vcc 3.39, reset reason Turned on by main processor WiFi flash size 4194304, free heap 25064 WiFi IP address 192.168.1.206 WiFi signal strength -64dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: no data receivedthank you
-
please can you provide your config
-
@paboman I can't see anything obvious in your M122 report. It says that the board was reset, that's about it.
Try updating your firmware to 2.05.1. This fixed a problem in 2.05:
Fixed a 1-character buffer overflow in class OutputBuffer. The effects of this overflow were unknown but potentially severe.
From https://github.com/Duet3D/RepRapFirmware/blob/dev/WHATS_NEW.md
Ian
-
@droftarts
I run M122 after reboot because the duet was not responding at allThanks I will try to update the firmware
