Added Duex5 - Really need some help
-
@GeorgeM said in Added Duex5 - Really need some help:
I just changed the config.g with all mention of the U parameters deleted.
Can you share that version of your config?
-
Ok, I went and changed it line by line. I am able to get rid of all the U parameters except in M92. If I delete them in M92 it will not work.
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Mon Jun 15 2020 11:14:50 GMT-0600 (Mountain Daylight Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name
M669 K1 ; select CoreXY mode; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes backwords - X
M569 P1 S0 ; physical drive 1 goes backwards - Y
M569 P2 S0 ; physical drive 2 goes backwards - Z right side
M569 P3 S1 ; physical drive 3 goes forwards - Exturder
M569 P4 S0 ; physical drive 4 goes backward - Z left side
M584 X0 Y1 Z2:4 E3 ;two Z Motors connected to driver outputs Z and E1
M671 X-20:310 Y0:0 S2 ;Leadscrew at left (connected to Z) and right connected to E1) of X axis
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X101.84 Y104.96 Z402.42 U402.42 E2892.00 ; set steps per mm
M566 X500.00 Y500.00 Z100.00 E60.00 ; set maximum instantaneous speed changes (mm/min)
M203 X10000.00 Y10000.00 Z6000.00 E8000.00 ; set maximum speeds (mm/min)
M201 X800.00 Y800.00 Z30.00 E120.00 ; set accelerations (mm/s^2)
M906 X1200.00 Y1200.00 Z800.00 E500.00 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X-25 Y-15 Z0 S1 ; set axis minima
M208 X330 Y340 Z300 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
;M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M950 S0 C"duex.pwm1" ; create servo pin 0 for BLTouch
M558 P9 C"zprobe.in" H3 F120 T4800 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X30 Y-10 Z.48 ; set Z probe trigger value, offset and trigger height
M557 X15:285 Y15:275 P4:4 ; define mesh grid
M376 H10; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; diable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S300 ; Set temperature limit for heater 1 to 300C
M308 S5 P"drivers" Y"drivers" A"Driver" ; set virtual heater for stepper drivers; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F3 C"duex.fan3" Q1000 ; create fan 3 on pin fan3 and set its frequency
M106 P3 S0 H-1 ; set fan 3 value. Thermostatic control is turned off
M308 S4 P"mcu-temp" Y"mcu-temp" A"MCU" ; set virtual heater for MCU
M950 F4 C"!duex.fan4" Q25000 ; Define Fan_4 for use - Duet board cooling - PWM fan
M106 P4 S4 T45:65 H100:101:102 ; set fan 4 value, turn if the CPU temp (or driver temps) reaches 45C, increase to full speed at 65C; Tools
M563 P0 S"E3D_V6" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P2 S"Laser" F3 ` ; define tool 2
G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets
;G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C; Custom settings are not defined
M501 ; Load saved parameters from non-volatile memory -
by the way, Thank you for the time you are spending on this for me.
-
@GeorgeM said in Added Duex5 - Really need some help:
If I delete them in M92 it will not work.
What exactly does it do?
Where are your motors plugged in?
With the U stuff completely removed and the Duex disconnected what do you get when you send M98 P"config.g"?
-
When I try to home it stays busy and the arrow circles spins and then I get a homing error.
Same with either x or y. Same if I comment out the raising of z before I home.Motors are plugged into:
X in 0
Y in 1
Z in 2
E in 3 or E0
U in 4 or E1Well what do you know. With the duex removed and U removed from M92, it homed correctly.
With the duex reconnected and U removed from M92 - no movement and driver 5 error is back. -
I need to leave for about 90 minutes
-
@GeorgeM said in Added Duex5 - Really need some help:
Well what do you know. With the duex removed and U removed from M92, it homed correctly.
With the duex reconnected and U removed from M92 - no movement and driver 5 error is back.The first point I expected. The second point is still perplexing.
What happens with duex connected and M92 U removed?
-
@Phaedrux said in Added Duex5 - Really need some help:
What happens with duex connected and M92 U removed?
With the duex reconnected and U removed from M92 - no movement and driver 5 error is back.
-
As a sanity check, I configured X to use driver 5. When doing so I get no movement from X motor.
-
How have you the Duex wired?
https://duet3d.dozuki.com/Wiki/Duex2_and_Duex5_Features#Section_Wiring
-
@Phaedrux said in Added Duex5 - Really need some help:
How have you the Duex wired?
https://duet3d.dozuki.com/Wiki/Duex2_and_Duex5_Features#Section_Wiring
Exactly like that.
-
I think you have a failed driver 5 on your Duex. When was it purchased and from where?
-
@Phaedrux said in Added Duex5 - Really need some help:
I think you have a failed driver 5 on your Duex. When was it purchased and from where?
June 26 from Filastruder. I contacted Tim there and gave him the link to this thread.
-
Well at least our endeavour wasn't totally fruitless.
-
I do appreciate all your attention to this. You were able to get me corrected about the U parameters. That's a win.
I do need to start a new thread about why my laser wont operate from gcode commands.
