Stepper issues
-
@jumpedwithbothfeet I think you may be encountering an issue in RRF3 where config-override is not written correctly.
Can you send M115 and report the version string?
Are you using a rpi with your Duet 3?
-
@Phaedrux Yup RPI3B+ with Duetpi gui
05/04/2020, 19:52:48
M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC v0.6 or 1.0 FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet 3 MB6HC FIRMWARE_DATE: 2020-01-03b3I also copied my Autopid readings -
M307 H0
Heater 0 model: gain 150.3, time constant 632.1, dead time 1.0, max PWM 1.00, calibration voltage 23.9, mode PID
Computed PID parameters for setpoint change: P780.7, I31.671, D525.4
Computed PID parameters for load change: P780.7, I140.683, D525.4M307 H1
Heater 1 model: gain 311.0, time constant 120.0, dead time 4.2, max PWM 1.00, calibration voltage 24.0, mode PID
Computed PID parameters for setpoint change: P16.5, I0.735, D48.2
Computed PID parameters for load change: P16.5, I1.492, D48.2 -
Alright, I'm not sure if that particular issue has been resolved yet, but there was just an update released the other day for the Duet3+pi which you should look into updating to as there has been a lot of work done since version 3.0.
https://forum.duet3d.com/topic/15317/reprapfirmware-3-01-rc6-released
https://forum.duet3d.com/topic/15342/duet-web-control-2-1-1-released
https://forum.duet3d.com/topic/15343/dsf-1-3-1-unstable-released -
@Phaedrux no worries I was holding off updating till I got a basic grasp of how everything works, ill make that my first job now, if it sorts out the override happy days, if not I believe I can manually edit the override.g with the Autotune figures If I read the guide correctly
-
@jumpedwithbothfeet My Bad.
and apologies.
I forgot to tell you that part about changing the config.g and saving it.I'll go back to my corner now!
Paul -
@PaulHew not your fault bud, I’m the novice here I think I’ve even messed up the firmware upload it’s taking forever to install!
-
@Phaedrux the firmware upload I suspect has locked up, I have “please wait while updates are being installed...” there are no system files on display and it’s been at least 30mins so far is there anything I can do or should I just wait?
-
Seeing as you're using the raspberry pi I believe the means of updating would be to use apt update on the pi. I believe you'd also need to have the unstable repository added.
https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Software_Installation
-
@Phaedrux does that not only apply to raspbien? I’m running duetpi running sudo update/upgrade was one of the first things I did when I installed the board.
-
I think you'd still need the unstable repository added to get the latest.
-
@Phaedrux i think it did it, i ran M115 again and got this -
M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 MB6HC FIRMWARE_VERSION: 3.01-RC6 ELECTRONICS: Duet 3 MB6HC v0.6 or 1.0 FIRMWARE_DATE: 2020-04-03b3hopefully this will help solve some issues, thank you for your help its much appreciated
