slant lines

droftarts

@matt3o I don't think you ever posted your config.g (or at least, I can't find it). Can you post that? And firmware version? Send M115 and post response.

Ian

matt3o

@droftarts you are totally right.

Of course many parameters change based on the extruder that I'm using.

FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.04 ELECTRONICS: Duet WiFi 1.02 or later + DueX5 FIRMWARE_DATE: 2019-11-01b1



; General
; --------------------------------------------------

M111 S0							; Debug off
M550 PCorezilla					; Machine name and Netbios name (can be anything you like)
M551 Preprap					; Machine password (used for FTP)

M552 S1							; Turn network on
;M586 P1 S1						; Enable FTP

M555 P2							; Set output to look like Marlin
G21								; Work in millimetres
G90								; Send absolute coordinates...
M83								; ...but relative extruder moves
M669 K1							; CoreXY mode


; Motors configuration
; --------------------------------------------------

M584 X0 Y1 Z2:3:4 E6		; set drive mapping
M569 P0 S1			; Drive 0 goes backwards | X stepper
M569 P1 S1			; Drive 1 goes backwards | Y stepper
M569 P2 S0			; Drive 2 goes forwards  | Z stepper  - Z1
M569 P3 S0			; Drive 3 goes forwards  | E0 stepper - Z2
M569 P4 S0			; Drive 4 goes forwards  | E1 stepper - Z3
M569 P5 S1			; Drive 5 goes forwards  | extruder

M350 X16 Y16 I1			
M350 Z16 I1
M350 E16 I1				
M92 X160 Y160 Z1600 E415		; Steps/mm
M906 X1400 Y1400 Z1400 E500 I60		; set motor currents (mA), motor idle factor (%)
M201 X2000 Y2000 Z20 E200		; set accelerations (mm/s^2)
M203 X12000 Y12000 Z600 E1200		; set maximum speeds (mm/min)
M566 X720 Y720 Z15 E6			; maximum jerk speeds (mm/min)


; Axis limit and endstops
; --------------------------------------------------

M208 X0:406 Y0:390 Z0:390		; set axis limits

M574 X1 Y1 S1					; set active high endstops
M574 Z1 S2						; set endstops controlled by probe

; Z-Probe
M558 P1 I0 H5 R0.4 F400 T6000	; set Z probe type to effector and the dive height + speeds
G31 P543 X0 Y0 Z-0.1				; set Z probe trigger value, offset and trigger height
M557 X20:370 Y20:370 S50			; define mesh grid

; Leadscrew locations
M671 X428.4:-31.5:198.4 Y38.5:38.5:413.5 S25


; Tools: Heaters, thermistors and fans
; --------------------------------------------------

M305 P0 S"Bed" T100000 B3950 R4700 H0 L0				; Bed thermistor
M305 P3 S"E0" T500000 B4723 C1.196220e-7 R4700 H6 L0	; E0 thermistor

M570 S180						; Hotend may be a little slow to heat up so allow it 180 seconds

M143 H0 S120					; Maximum H0 (Bed) heater temperature
M143 H3 S290					; Maximum extruder 3 heater temperature

; Adjustments heaters
M307 H0 A301.3 C836.5 D0.9 B1  ; bed heater
M307 H3 A646.6 C192.9 D3.8 B0   ; tool 0 heater

; Fans
M106 P3 T45 H3					; Enable thermostatic mode for fan 3 on heater 3
M106 P4 H-1						; Disable thermostatic mode for fan 4 (part fan)

M106 P4 S0

; Tool definitions
M563 P0 D0 H3 F4				; Define tool 0 heater 3 fan 4
G10 P0 S0 R0					; Set tool 0 operating and standby temperatures

; Closing
; --------------------------------------------------

M208 S1 Z-0.2					; set minimum Z
T0								; select first hot end

droftarts

@matt3o

Add M569 P6 S1 after the other drives, but I don’t think that will make much difference.

Ian

matt3o

@droftarts yeah that comes from testing various stepper drivers. Usually it's on E5. It makes no difference but thanks for checking that out

droftarts

@matt3o You could also update to 2.05.1. Again, probably won't make a difference, but would be good to see if it changes anything.

The other thing I'd do is swap the bed motors to the Duex, and use the Duet for X, Y and E. eg M584 X0 Y1 Z5:6:7 E3. This will check it's a comms issue between the Duet and Duex. I don't know if you've always been using the Duex for the extruder, or have tested it the other way around, though.

Ian

matt3o

@droftarts I'll update to v3 tomorrow, I already have the updated config, I just wanted to to fix this issue first, but I guess it's worth trying upgrade the duet.

In the various tests I've done I believe I also tried a stepper on the duet for the extruder moving one of the other axis on the duex.

I think it's worth trying a completely new controller, since that is the only thing that I haven't tried to change at this point. Not that it's a good time to buy 3d printing stuff with coronavirus and all.

droftarts

@matt3o I have to ask... is this a clone or genuine Duet? If it's genuine, and swapping the board fixes the problem, and the board is less than 6 months old (from your first post in this thread) it should be covered by the warranty.

Ian

bondus

@matt3o said in slant lines:

could it be that my motion system is so well tuned that it emphasizes the extruder "signature"?

I think you might be right. In my experience many extruders have a very small periodic error. In most cases it is not visible. It depends on what hotend you have too, I would guess that if the "melt-pot" is big it will provide some elasticity inside the hot end.

My standard test object is a square cone in vase made. It is very good for showing periodic extrusion errors and mechanical errors. The varying of the extrusion length over height of the cone will make periodic extrusion errors show up very clearly as interference patterns.

Even a BMG through a 50cm bowden tube shows extrusion errors (ignore the slant lines in this case, they are mechanical). The errors in this case are so small that in any normal case it is totally invisible, this test provokes it. Interefernce waves.jpg

matt3o

@droftarts hey! of course it's a genuine duet! we are not lamerino here! BTW, I'm not covered by the warranty because I modded the wifi module.

@bondus said in slant lines:

I think you might be right. In my experience many extruders have a very small periodic error. In most cases it is not visible. It depends on what hotend you have too, I would guess that if the "melt-pot" is big it will provide some elasticity inside the hot end.

yeah that's my thought too... I'll also try a different hotend (mosquito right now).

matt3o

Quick update. I replaced the mosquito with an E3D hotend (also thermistor and heater). The texture changed again but I still get the slant lines pattern.

So at this point the only element left to change is the controller... It will take some time to get my hands on a new controller with the current covid19 situation but I'll update as soon as I get it.

matt3o

It took me a while but I wanted to give a closure to this issue in case someone ends up here from google or forum search.

The following is my current status, printed at 100mm/s with 4500 acceleration.

There are still a few issues that I'm trying to fix, but things are slowly getting better.

This is a corexy, they are heinous machines. Do yourself a favor and build a Cartesian

The bare minimum you need:

super steady frame
good vibration abortion
study gantry, use metal to hold the gantry if you can, otherwise 3d print big brackets and add more screws than you think it's necessary
tight belts
don't spare on pulleys and idlers, get good and correctly sized shims between the idlers. I got "precision shims" but they were a little rough on the edges and I had to file all of them
after you first assembled the machine, give your screws another go, for some reason they like to loosen up
proper part cooling (duh)

I've rebuilt my printer with all of the above in mind, and that helped to reach relatively high speed/acceleration but what really helped with the slant texture is... tune your extruder/hotend.

When the machine is overall well calibrated you are going to see every little defect generated by the extruder/hotend. Even an over-extrusion of 1% or a +2-3°C in temp can generate a bad surface texture.

Try to slice with different slicers (Cura seems a little less finicky) or change from Relative to Absolute (or vice versa) extrusion.

If tests and benchmarks say that your motor is calibrated properly but you still see a slanted texture, don't trust them and start lowering the extrusion multiplier and/or the temperature. You'll be surprised by how much of a difference a 1% does.

If the surface still look bad, try to change the extruder motor. I've been lucky with both 0.9° Nema17 and 1.8° Nema14 from LDO. I had a few issues with moons on the extruder, while they are great on XYZ.

Edit: almost forgot! Align your rails. Get a precision gauge and align your rails. When they are aligned, aligned them again

Hope that helps. Happy printing.