Posts made by yaniv

Work like a charm! Thank you very much!

It's Original.

Front:

Back:

Hi,
I have a Duet Ethernet board, I'm connect it to the PC with the USB only, I put the 2.02a firmware to the board in this manner:
(https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Fallback_procedure_Num_3)
I delete all lines of the network on the config.g file (M552 etc)
I connected to the board with RepetierHost and try to enable the network with M552 S1 P0.0.0.0 but I got this error all the time:
"M552: Bad or missing SSID"
I can't turn the Ethernet on, This is the M122 after I'm run M552 S0:

19:44:39.807 : serial: M552 S1 P0.0.0.0
19:44:39.808 : Error: M552: Bad or missing SSID
19:44:39.809 : serial: M552 S0
19:44:39.810 : serial: M122
19:44:39.817 : === Diagnostics ===
19:44:39.817 : RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later
19:44:39.817 : Board ID: 08DDM-9FAM2-LW4SD-6J9F2-3S86N-KLWRX
19:44:39.817 : Used output buffers: 1 of 20 (11 max)
19:44:39.817 : === RTOS ===
19:44:39.817 : Static ram: 25524
19:44:39.817 : Dynamic ram: 98436 of which 0 recycled
19:44:39.817 : Exception stack ram used: 280
19:44:39.817 : Never used ram: 6832
19:44:39.817 : Tasks: NETWORK(ready,1396) HEAT(blocked,948) MAIN(running,3760) IDLE(ready,200)
19:44:39.817 : Owned mutexes:
19:44:39.817 : === Platform ===
19:44:39.817 : Last reset 00:26:08 ago, cause: reset button or watchdog
19:44:39.817 : Last software reset time unknown, reason: Hard fault, spinning module Platform, available RAM 46604 bytes (slot 1)
19:44:39.817 : Software reset code 0x4030 HFSR 0x40000000 CFSR 0x00000400 ICSR 0x0440f803 BFAR 0xe000ed38 SP 0x200049c4 Task 0x4e49414d
19:44:39.818 : Stack: 00447339 20000032 81000000 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 a5a5a5a5 2000857c 0045f05c 2000857c 0044ba25 00000054 00000000 2000857c 0044b89d 2000857c 0045f05c a5a5a5a5 230020a4
19:44:39.818 : Error status: 0
19:44:39.818 : Free file entries: 10
19:44:39.818 : SD card 0 detected, interface speed: 20.0MBytes/sec
19:44:39.818 : SD card longest block write time: 0.0ms, max retries 0
19:44:39.818 : MCU temperature: min 35.9, current 36.4, max 36.4
19:44:39.818 : Supply voltage: min 0.6, current 0.6, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
19:44:39.818 : Driver 0: ok, SG min/max not available
19:44:39.818 : Driver 1: ok, SG min/max not available
19:44:39.818 : Driver 2: ok, SG min/max not available
19:44:39.818 : Driver 3: ok, SG min/max not available
19:44:39.818 : Driver 4: ok, SG min/max not available
19:44:39.818 : Date/time: 1970-01-01 00:00:00
19:44:39.818 : Cache data hit count 3063926463
19:44:39.818 : Slowest loop: 0.25ms; fastest: 0.07ms
19:44:39.818 : I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
19:44:39.818 : === Move ===
19:44:39.818 : Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 240, MaxWait: 0ms, Underruns: 0, 0
19:44:39.818 : Scheduled moves: 0, completed moves: 0
19:44:39.818 : Bed compensation in use: none
19:44:39.818 : Bed probe heights: 0.000 0.000 0.000 0.000 0.000
19:44:39.818 : === Heat ===
19:44:39.818 : Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
19:44:39.818 : Heater 1 is on, I-accum = 0.0
19:44:39.818 : === GCodes ===
19:44:39.818 : Segments left: 0
19:44:39.818 : Stack records: 1 allocated, 0 in use
19:44:39.818 : Movement lock held by null
19:44:39.818 : http is idle in state(s) 0
19:44:39.818 : telnet is idle in state(s) 0
19:44:39.818 : file is idle in state(s) 0
19:44:39.818 : serial is ready with "M122" in state(s) 0
19:44:39.818 : aux is idle in state(s) 0
19:44:39.818 : daemon is idle in state(s) 0
19:44:39.818 : queue is idle in state(s) 0
19:44:39.818 : autopause is idle in state(s) 0
19:44:39.818 : Code queue is empty.
19:44:39.818 : === Network ===
19:44:39.818 : Slowest loop: 0.19ms; fastest: 0.00ms
19:44:39.818 : Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
19:44:39.818 : HTTP sessions: 0 of 8
19:44:39.818 : - WiFi -
19:44:39.818 : Network state is starting
19:44:39.818 : WiFi module is disabled
19:44:39.818 : Failed messages: pending 0, notready 0, noresp 0
19:44:39.818 : Socket states: 0 0 0 0 0 0 0 0

It's seems that that the board think it have Wifi Module instead of Ethernet Module.

I also copy to the SD/sys this files from the release of 2.02:
Duet2CombinedFirmware.bin
DuetMaestroFirmware.bin
DuetWiFiServer.bin
and this file from this release:
iap4e.bin

and tried to update with the M997 S0:1:2 command but the module still don't work/recognized.

It was worked before I tried to upgrade from 1.21 (If I remembered right), I first tried to upgrade from the web interface and when the the display show duplicated file/macro and I can't upgrade from the web interface anymore I tried the M997 method and after that the Erase etc.

This is what I get after M997 S0:

19:55:56.067 : serial: M997 S0
19:55:56.068 : Read 0 1 16384
|....|
19:55:57.618 : Read 0 1 20790
19:56:32.051 : No start signal detected - forcing start
19:56:32.055 : D
19:56:32.060 : FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.02(RTOS) ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2018-12-24b1
19:56:32.061 : X:0.000 Y:0.000 Z:0.000 E0:0.0 E1:0.0 E2:0.0 E3:0.0 E4:0.0 E5:0.0 E6:0.0 E7:0.0 E8:0.0 Count 0 0 0 Machine 0.000 0.000 0.000
19:56:32.063 : serial: T0
19:56:32.065 : serial: M20
19:56:32.065 : Read 0 1 16384
19:56:32.066 : Read 0 1 16640
19:56:32.067 : GCode files:
19:56:32.067 : NONE
19:56:32.067 : serial: M111 S6
19:56:32.069 : serial: T0
19:56:32.070 : serial: M80
19:57:12.081 : Communication timeout - reset send buffer block
19:57:12.083 : serial: M105
19:57:12.083 : serial: M552 S1
19:57:14.929 : serial: M105
19:57:17.991 : serial: M105
19:57:21.055 : serial: M105
19:57:23.634 : serial: M552 S1 P0.0.0.0
19:57:23.635 : Error: M552: Bad or missing SSID
19:57:24.112 : serial: M105
19:57:27.179 : serial: M105
19:58:07.206 : Communication timeout - reset send buffer block
19:58:07.207 : serial: M105
19:58:07.209 : serial: M552
19:58:07.209 : WiFi module is being started

What can I do to enable/use the Ethernet Module?