There was some extra code in the start code section that somehow got put back after I deleted it.. I edited the gcode to verify it wasw gone and printer is much better now/ Thanks!

Machine has been upgraded to 24V. I have a BL Touch installed and working. I have a BIQU H2 Direct drive Hotend Installed. I am using a 0.6 Nozzle. (Config File at end of Message)
The machine will home all axis in a decent manner no problem. but once I star a print it drops into granny gear forever more... I know it's probably something I have set wrong, but I'm not figuring it out and decided to ask for some guidance. While I am not new to 3D printing, I am new to REPRAP.

; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.12 on Sun Aug 28 2022 17:19:32 GMT-0400 (Eastern Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Creality CR-10S" ; set printer name
M950 P1 C"io0.out"
M950 P2 C"io2.out"

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0.0 S0 D3 ; physical drive 0.0 goes forwards
M569 P0.1 S0 D3 ; physical drive 0.1 goes forwards
M569 P0.2 S1 D3 ; physical drive 0.2 goes forwards
M569 P0.3 S0 D3 ; physical drive 0.3 goes forwards
M569 P0.4 S1 D3
M584 X0.0 Y0.1 Z0.2:0.4 E0.3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E917.25 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X30000.00 Y30000.00 Z900.00 E1500.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00: E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E600 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X-4 Y-25 Z0 S1 ; set axis minima
M208 X310 Y300 Z400 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"io5.in" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin !^io5.in
M574 Y1 S1 P"io6.in" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin !^io6.in
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"io3.out" ; create servo pin 0 for BLTouch
M558 P9 C"io3.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-15 Y-30 Z 1.7 ; set Z probe trigger value, offset and trigger height
M557 X40:270 Y25:280 S20 ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 R0.209 K0.299:0.000 D6.89 E1.35 S1.00 B0 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 R2.740 K0.290:0.000 D14.05 E1.35 S1.00 B0 V24.3 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"out5" Q500 ; create fan 0 on pin out5 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out6" Q500 ; create fan 1 on pin out6 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
T0

Cura Settings ? which ones do you need to know... Don't know how to dump them so I can show them all... But I suspect the slicer is the main culprit here..