Is the duet WiFi documentation server down because I cannot connect on any device .
Posts made by Will Baxter
-
Server down
-
Server down
Is the documentation server down I cannot connect on any device .
-
RE: G32 not working properly
Yes everything works except the adjustment at the end of the probing
-
G32 not working properly
when i auto level using the G32 command when it is making the adjustments at the end i can see the bed being adjusted out of level . i run G32 3 times the bed is never level . any thoughts
-
RE: HomeZ
x axis goes the wrong way when i home all
my end stops are located bottom left corner
my origin is located bottom left corner
when i home the head travels towards origin; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool on Sun Jan 13 2019 13:36:28 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 X395 Y405 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 X5 Y-5 F6000 ; go back a few mm
G1 S1 X395 Y405 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X60 Y60 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool on Sun Jan 13 2019 13:36:28 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 Y405 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y-5 F6000 ; go back a few mm
G1 S1 Y405 F360 ; move slowly to Y axis endstop once more (second pass)
G1 Z-5 F6000 S2 ; lower Z again
G90 ; absolute positioning -
RE: HomeZ
homex.g file
; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool on Sun Jan 13 2019 13:36:28 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 X-395 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000 ; go back a few mm
G1 S1 X-395 F360 ; move slowly to X axis endstop once more (second pass)
G1 Z-5 F6000 S2 ; lower Z again
G90 ; absolute positioning -
RE: HomeZ
@will-baxter config.g file
Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sun Jan 13 2019 13:36:28 GMT+0000 (Greenwich Mean Time); General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves; Network
M550 PBaxters beast ; Set machine name
M551 Pboomboom6663 ; Set password
M552 S1 ; Enable network
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Drives
M569 P0 S0 ; Drive 1 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes backwards
M569 P3 S0 ; Drive 3 goes forwards
M569 P4 S0 ; Drive 4 goes forwards
M569 P5 S0 ; Drive 5 goes forwards
M569 P6 S1 ; Drive 6 goes forwards
M584 X0 Y1:2 Z3:4:5 E6
M671 X390:219:0.0 Y400:10:400 S4 ; leadscrews at front left, front right and rear middle
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y79.9 Z386.5 E420 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 E1200 ; Set maximum speeds (mm/min)
M201 X500 Y20 Z250 E250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X390 Y400 Z600 S0 ; Set axis maxima; Endstops
; Z-Probe
M574 X2 Y2 Z0 S1 ; Define active low and unused microswitches
M558 P1 I0 R0.4 F300 X0 Y0 Z0
G31 X0 Y0 Z-0.1 P600
M557 X25:375 Y15:395 S50 ; Define mesh grid; Heaters
M140 H-1 ; Disable heated bed
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S300 ; Set temperature limit for heater 1 to 260C; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C; Automatic saving after power loss is not enabled
; Custom settings are not configured
HomeZ.g file
homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool on Sun Jan 13 2019 13:36:28 GMT+0000 (Greenwich Mean Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G90 ; absolute positioning
G1 X15 Y15 F6000 ; go to first probe point
G30 ; home Z by probing the bed; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 S2 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning -
HomeZ
why is it that my X axis goes the wrong way when i use the HomeZ but homes fine when i use the home x
-
RE: Cant connect to web controller after 1.19 upgrade
I have followed instructions at https://duet3d.com/wiki/Upgrading_to_Du … mware_1.19 ? . I have also copy/paste from the web page . Nothing is working . Iam getting this creating a macro file right, it is just G code in a text file.
-
RE: Cant connect to web controller after 1.19 upgrade
it reports found wifi module idle no rememberd networks
-
RE: Cant connect to web controller after 1.19 upgrade
cant connect by usb but there is an error on the paneldue
it reads wifi reported error:no known networks found wifi module is idle
-
RE: Cant connect to web controller after 1.19 upgrade
yes i did what do you sugest
-
Cant connect to web controller after 1.19 upgrade
Upgrade worked i can connect to the printer using simply3d with usb cable and my paneldue but no luck on my mac with wifi or usb cable . The router has the duetwifi disconnected . i know it has to do with the web controller but i have created a www file but still no luck . any help would be appreciated thanks
-
1.19 upgrade trouble with web control
need help installing web control zip file after 1.19 firmware upgrade i have read the instructions about /www root file but do not understand give it to me in layman's terms please the more basic the better
-
RE: Firmware wishlist and priorities for Duet WiFi and Duet Ethernet
my preference would be 5 5 5 5 5 for 4 z motors and quickly pleace
-
Checking the trigger height
when i enter G1 Z5 the bed moves 50mm not 5mm any thoughts
-
RE: Z stepper motors
I have now purchased a duex 5 expansion board and need help maping my 1 x axis stepper motor 2 y axis stepper motors and 3 z axis stepper motors .
When using the M584 gcode does it go in any particular file and in any particular order thanks in advance Will -
RE: Z stepper motors
I thought that so how do i get the same power to all three motors thanks