@dc42 I will. Thank you.

@dc42 said in Toolboard 1.1 accelerometer not reporting...:

I bought 2x1LCs 1.1 around June. Mounted and briefly tested accelerometers. Used normally up until few days ago when I tried to play with Input Shaping. Then I noticed that one accelerometer is missing.

M122 B20 (Accelerometer detected: no)

Diagnostics for board 20:
Duet TOOL1LC rev 1.1 or later firmware version 3.4.0beta5 (2021-10-12 13:59:06)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
Never used RAM 3412, free system stack 2745 words
Tasks: Move(notifyWait,5.5%,99) HEAT(notifyWait,1.9%,97) CanAsync(notifyWait,0.0%,58) CanRecv(notifyWait,1.0%,75) CanClock(notifyWait,0.2%,64) TMC(notifyWait,25.2%,57) MAIN(running,24.1%,340) IDLE(ready,0.0%,27) AIN(delaying,42.0%,142), total 100.0%
Last reset 12:38:33 ago, cause: VDD brownout
Last software reset time unknown, reason: AssertionFailed, available RAM 4192, slot 1
Software reset code 0x0120 ICSR 0x00000000 SP 0x20003ef4 Task  Freestk 129 bad marker
Stack: 00000544 00022ffc 00019b65 20003134 00016cff 20003134 000163d1 20000ed0 00000000 00000001 00008275 200071c8 200071c8 200071e0 00000000 20000f50 00011647 000223b8 00022474 00021ac8 00019b05 200071c8 200071c8 20000f50 000083ed 200071d8 000009c6
Driver 0: pos 17231199, 699.3 steps/mm,ok, SG min/max 0/464, read errors 17, write errors 0, ifcnt 16, reads 24255, writes 16, timeouts 11, DMA errors 0, failedOp 0x01, steps req 46168729 done 46168229
Moves scheduled 710857, completed 710856, in progress 1, hiccups 242, step errors 0, maxPrep 1582, maxOverdue 4140, maxInc 3603, mcErrs 0, gcmErrs 0
Peak sync jitter 4/12, peak Rx sync delay 231, resyncs 0/0, next step interrupt due in 1341 ticks, enabled
VIN voltage: min 23.8, current 24.2, max 24.3
MCU temperature: min 36.8C, current 51.1C, max 55.9C
Last sensors broadcast 0x00000002 found 1 53 ticks ago, loop time 0
CAN messages queued 920280, send timeouts 0, received 1312488, lost 0, free buffers 37, min 34, error reg 20000
dup 0, oos 2/0/1/0, bm 1, wbm 4140, rxMotionDelay 933, adv 34249/74661
Accelerometer detected: no
I2C bus errors 0, naks 12, other errors 0

M122 B21

Diagnostics for board 21:
Duet TOOL1LC rev 1.1 or later firmware version 3.4.0beta5 (2021-10-12 13:59:06)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
Never used RAM 2608, free system stack 2789 words
Tasks: Move(notifyWait,0.0%,153) HEAT(notifyWait,1.3%,105) CanAsync(notifyWait,0.0%,64) CanRecv(notifyWait,0.2%,77) CanClock(notifyWait,0.2%,64) ACCEL(notifyWait,0.0%,61) TMC(delaying,24.7%,57) MAIN(running,32.5%,350) IDLE(ready,0.0%,27) AIN(delaying,41.2%,142), total 100.0%
Last reset 12:39:11 ago, cause: power up
Last software reset time unknown, reason: AssertionFailed, available RAM 3392, slot 1
Software reset code 0x0120 ICSR 0x00000000 SP 0x2000415c Task  Freestk 129 bad marker
Stack: 00000544 00022ffc 00019b65 20003134 00016cff 20003134 000163d1 20000ed0 00000000 00000001 00008275 200071c8 200071c8 200071e0 00000000 20000f50 00011647 000223b8 00022474 00021ac8 00019b05 200071c8 200071c8 20000f50 000083ed 200071d8 000009c7
Driver 0: pos 0, 699.3 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 13, reads 34773, writes 13, timeouts 21, DMA errors 0, failedOp 0x6f, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, step errors 0, maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
Peak sync jitter 5/14, peak Rx sync delay 218, resyncs 0/0, no step interrupt scheduled
VIN voltage: min 24.2, current 24.3, max 24.4
MCU temperature: min 33.2C, current 41.9C, max 46.5C
Last sensors broadcast 0x00000004 found 1 53 ticks ago, loop time 0
CAN messages queued 911096, send timeouts 0, received 592244, lost 0, free buffers 37, min 37, error reg 20000
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0
Accelerometer detected: yes, status: 00
I2C bus errors 0, naks 3, other errors 0

That is what I get when trying to configure.

Hi,

I have IDEX cartesian printer running on Duet 3 6HC with two Toolboards 1LC 1.1 connected via CAN. FW is 3.4b5. I have them for some time now and finally wanted to try input shaping.

I've noticed that accelerometer on 20.0 is not found, but on 21.0 its ok. Is there anything I can do to fix it or look for cause other than hardware failure?

@dc42 I experimented some more and came up with testing routine. Trying to set StealthChop to SpreadCycle at low speed. No luck... Or maybe at 10mm/s is all I can get?

Accel/jerk are halved in comparison to normal operation.

Each testing sequence consists of:

• Configuration
• Homing with tuning
• Three sets of moves of Y and U separately
• Each set has different speed - 10, 50 and 100mm/s

It runs five tests with different configuration each:

• StealthChop to SpreadCycle with switch at 10.4 mm/s
• StealthChop to SpreadCycle with switch at 52.1 mm/s
• StealthChop to SpreadCycle with switch at 93.8 mm/s
• Pure SpreadCycle
• Pure StealthChop

I've recorded a routine with first 3 sequences. Every time movement is above switch speed then "clack" happens. Its visibly less noticeable at low setting, but is still there. As it's increased then it gets much worse.

If you could look if I did homing/tuning correctly, please.

I'll proceed to experimenting with different speeds. Previously when I picked different values for M569 and M915 I've got some improvement - clacking was getting less and less visible.

Thanks for your time and input.

Video (last two removed for brevity):
https://youtu.be/yojaNXBJG9s

Macros:
stealthChop.home.g

; Homing and tuning
M18 X U Y Z						; Disable motors
M17 X U Y Z 					; Enable motors
G4 P100							; Wait

G91								; Relative positioning
G1 Z5 F1000 H2					; Lift Z relative to current position
G1 X-999 U999 Y-999 F3000 H1	; Move and Tune
G1 X5 U-5 Y5 F6000 H2			; Go back a few mm
G1 X-999 U999 Y-999 F360 H1		; Move again
G1 Z-5 F1000 H2					; Return Z to previous height
G90

; BLTouch preperation
M280 P0 S160				; Precautionary alarm release
M280 P0 S90				; Ensure the pin is raised

; Home Z using the Z-Probe
G91						; Relative positioning
G1 Z10 F1000 H2			; Lift Z relative to current position
G90						; Absolute positioning
G1 X-130 Y-115 F6000	; Move T0 to probing point, including probe offset
G30						; Probe the bed and set Z to the probe offset
G1 Z10 F1000			; Raise Z off the bed

stealthChop.test.g

; Initial settings
var distance = 30 ;mm 
var speed_high = 100 ;mm/s
var speed_high_min = 60 * var.speed_high;
var speed_med = 50 ;mm/s
var speed_med_min = 60 * var.speed_med;
var speed_low = 10 ;mm/s
var speed_low_min = 60 * var.speed_low;

G1 X-999 U0 Y0 F3000	; Prepare for test
G4 P1000

; Test Low Speed
while iterations < 3
	G1 U{var.distance/4} F{var.speed_low_min}
	G1 U{-(var.distance/4)} F{var.speed_low_min}
while iterations < 3
	G1 Y{var.distance/4} F{var.speed_low_min}
	G1 Y{-(var.distance/4)} F{var.speed_low_min}
	
; Test Medium Speed
while iterations < 3
	G1 U{var.distance/2} F{var.speed_med_min}
	G1 U{-(var.distance/2)} F{var.speed_med_min}
while iterations < 3
	G1 Y{var.distance/2} F{var.speed_med_min}
	G1 Y{-(var.distance/2)} F{var.speed_med_min}

; Test High Speed
while iterations < 3
	G1 U{var.distance} F{var.speed_high_min}
	G1 U{-(var.distance)} F{var.speed_high_min}
while iterations < 3
	G1 Y{var.distance} F{var.speed_high_min}
	G1 Y{-(var.distance)} F{var.speed_high_min}

stealthChop.spreadCycle.test.g

; RR VCast IDEX (Cartesian)
; Duet 3 6HC TMC5160
; Testing U and Y
; XUY using 2.5A/3.1V LDO-42STH47-2504AC
;		https://www.ratrig.com/nema-17-stepper-motor.html
; 1. Load StealthChop to SpreadCycle settings
; 2. Tune drivers
; 3. Run test for StealthChop to SpreadCycle
; 4. Run test for StealthChop only
; 5. Run test for SpreadCycle only

G4 S5 ; Time to start recording :)

; Accel/Jerk are halved in comparison to normal operation
M906 X2125 U2125 Y2125 	Z1600:1600 E350:350	I50		; set currents
M566 X350  U350  Y350   Z60:60     E300:300			; set maximum instantaneous speed changes (mm/min)
M203 X6000 U6000 Y6000  Z1800:1800 E3600:3600      	; set maximum speeds (mm/min)
M201 X400  U400  Y450   Z100:100   E600:600        	; set accelerations (mm/s^2)
M204 P400  T400

;------------------------------------
;---- StealthChop to SpreadCycle ----
;------------------------------------

echo "Enable StealthChop to SpreadCycle settings (Switch Speed - 10.4 mm/s)"

; Reset Coolstep
M915 P0.0:0.1:0.2:0.3:0.4:0.5 T1 ; disable coolstep
M915 P20.0:21.0 T1 ; disable coolstep

; Set U 
M569 P0.1 S0 D3 V900 H900
M915 P0.1 T900

; Set Y
M569 P0.2 S0 D3 V900 H900
M915 P0.2 T900

; Homing and tuning
M98 p"/macros/stealthChop.home.g"
M98 p"/macros/stealthChop.test.g"

echo "Enable StealthChop to SpreadCycle settings (Switch speed - 52.1 mm/s)"

; Reset Coolstep
M915 P0.0:0.1:0.2:0.3:0.4:0.5 T1 ; disable coolstep
M915 P20.0:21.0 T1 ; disable coolstep

; Set U
M569 P0.1 S0 D3 V180 H180
M915 P0.1 T180

; Set Y
M569 P0.2 S0 D3 V180 H180
M915 P0.2 T180

; Homing and tuning
M98 p"/macros/stealthChop.home.g"
M98 p"/macros/stealthChop.test.g"
	
echo "Enable StealthChop to SpreadCycle settings (Switch speed - 93.8 mm/s)"

; Reset Coolstep
M915 P0.0:0.1:0.2:0.3:0.4:0.5 T1 ; disable coolstep
M915 P20.0:21.0 T1 ; disable coolstep

; Set U
M569 P0.1 S0 D3 V100 H100
M915 P0.1 T100

; Set Y
M569 P0.2 S0 D3 V100 H100
M915 P0.2 T100

; Homing and tuning
M98 p"/macros/stealthChop.home.g"
M98 p"/macros/stealthChop.test.g"

;------------------------------------
;---- SpreadCycle only ----
;------------------------------------

echo "Enable SpreadCycle settings"

; Reset Coolstep
M915 P0.0:0.1:0.2:0.3:0.4:0.5 T1 ; disable coolstep
M915 P20.0:21.0 T1 ; disable coolstep

; Set U (Factory values)
M569 P0.1 S0 D2 H200
M915 P0.1 T2000

; Set Y
M569 P0.2 S0 D2 H200
M915 P0.2 T2000

; Homing and tuning
M98 p"/macros/stealthChop.home.g"
M98 p"/macros/stealthChop.test.g"

;------------------------------------
;---- StealthChop only ----
;------------------------------------

echo "Enable StealthChop settings"
; Reset Coolstep
M915 P0.0:0.1:0.2:0.3:0.4:0.5 T1 ; disable coolstep
M915 P20.0:21.0 T1 ; disable coolstep

; Set U (Above 100mm/s)
M569 P0.1 S0 D3 V50 H50
M915 P0.1 T50

; Set Y
M569 P0.2 S0 D3 V50 H50
M915 P0.2 T50

; Homing and tuning
M98 p"/macros/stealthChop.home.g"
M98 p"/macros/stealthChop.test.g"

@dc42 That is only homex.g file. After that I run homeu.g, homey.g and finally homez.g calling one after another using M98 P from homeall.g

To have it working properly I cannot tune them separately, but have to do it in one move? Correct?

@dc42 Yes. I already did that. But maybe version with M17 is more reliable?

I ran your corexy test to confirm is it actually changing something and it is (https://forum.duet3d.com/topic/16297/help-needed-with-duet-3-6hc-tmc5160-stealthchop-config/75?_=1634594365615)

echo "Running homex.g"

G91															; Relative positioning
G1 H2 Z0.02 F3000
G4 P250
G1 Z5 F1000 H2												; Lift Z relative to current position
G1 H2 X0.02 F3000
G4 P250
G1 X-999 F6000 H1											; Move X-axis to the endstop and stop (first pass)
G1 X5 F6000	H2												; Go back a few mm
G1 X-999 F360 H1											; Move X-axis to the endstop once more (second pass)
G1 Z-5 F1000 H2												; Return Z to previous height
G90															; Absolute positioning

@dc42 Thanks for a rapid answer.

So it was my lack of understanding.

On Prusa/Bear that I duetized (Duet 3 mini 5+) it worked quickly just using 2nd strategy. Just configured StealthChop only mode and it worked without layer shifts up to 100mm/s - which I never excedeed. Probably worked due to different steppers, masses etc.

I'll do a step back then. First trying to tune speed/acc/jerk as currently I have mix of values provided by manufacturers (RR and Orbiter) and what produced good prints. Then retry setting StealthChop by adjusting jerk and drivers to find proper speed to switch to SpreadCycle.

My fallback will be to stay in one mode only.

One thing makes me wonder. Why I execute few moves consecutively with speed enabling SpreadCycle then sound stays. Not only when I move slow->fast->slow->fast.

Cheers!

Hi,

I have VCast IDEX with Duet 6HC and two 1LCs. Firmware is 3.4beta 5.

I am trying to configure StealthChop with switch to SpreadCycle at certain speed. So far it works, BUT with some issue I cannot understand.

When I enable SpreadCycle only. Then everything works ok. Prints are fine and motors sing their own songs on low speeds.

When I enable StealthChop up to 46.9mm/s (example) then when switch to SpreadCycle (above 46.9mm/s) happens there is an awful metal-like noise ("clack") on start of a movement/change direction. Prints are fine, but that sound defeats the purpose. It happens to all XUYZ as I run SpreadCycle on extruder motors.

Please bear in mind that on X (and most probably U) MGN carriage is very loose so contributes to awful noise while moving carriage around 60-75mm/s. Low quality unfortunately. To be replaced soon.

SpreadCycle only
https://youtu.be/0HDCOK81GIs

StealthChop with switch to SpreadCycle
https://youtu.be/jnZPjZBxbws

Macro routine does series of moves on each axis speeding up to 100mm/s and shortens movement distance to 2mm gradually. When StealthChop is enabled its nice and quiet, then SpreadCycle takes over and noise appears. Exactly same routine does not emit that sound when running in SpreadCycle only mode.

I've added driver tuning to my homing sequence and checked with dc42 corexy test script that it is actually tuning. Also tried various advices from forum. No luck so far...

Played with various THIGH, TPWMTHRS and TCOOLTHRS and I was either having StealthChop not enabling at all or that clacking sound. Tried with and without PA and Input Shaping enabled. I've managed get that clack sound a bit down but nothing close to how it is non-existing in SpreadCycle only mode.

Basically I could leave StealthChop on for all moves but during test prints I had layer shifts on Y (heavy bed) when executing travel moves around 100mm/s. So I would loose some speed.

STRANGEST (At least for me) part is that that noise is not present when only SpreadCycle is enabled.

Sooo... Any idea what I am doing wrong would be highly appreciated.

Motors config

M584 X0.0 U0.1 Y0.2 Z0.3:0.4 E20.0:21.0         ; set drive mapping	

var scSpeed_XU_TPWMTHRS = 200
var scSpeed_XU_THIGH  = 200 
var sdSpeed_XU = 200								

var scSpeed_Y_TPWMTHRS = 200 
var scSpeed_Y_THIGH  = 200 
var sdSpeed_Y_TCOOLTHRS = 200								

var scSpeed_Z_TPWMTHRS = 50
var scSpeed_Z_THIGH  = 50
var sdSpeed_Z_TCOOLTHRS = 50								

M569 P0.0 S0 D3 V{var.scSpeed_XU_TPWMTHRS} H{var.scSpeed_XU_THIGH}	                          	; physical drive 0.0 goes backwards X
M915 P0.0 T{var.sdSpeed_XU}		
M569 P0.1 S0 D3 V{var.scSpeed_XU_TPWMTHRS} H{var.scSpeed_XU_THIGH}                            	; physical drive 0.1 goes backwards U
M915 P0.1 T{var.sdSpeed_XU}		
M569 P0.2 S0 D3 V{var.scSpeed_Y_TPWMTHRS} H{var.scSpeed_Y_THIGH}                            	; physical drive 0.2 goes backwards Y
M915 P0.2 T{var.sdSpeed_Y_TCOOLTHRS}		
M569 P0.3 S1 D3 V{var.scSpeed_Z_TPWMTHRS} H{var.scSpeed_Y_THIGH}                            	; physical drive 0.3 goes forwards ZLeft
M915 P0.3 T{var.sdSpeed_Z_TCOOLTHRS}		
M569 P0.4 S1 D3 V{var.scSpeed_Z_TPWMTHRS} H{var.scSpeed_Z_THIGH}                              	; physical drive 0.4 goes forwards ZRight
M915 P0.4 T{var.sdSpeed_Z_TCOOLTHRS}		
M569 P20.0 S1 D2                          	; physical drive 20.0 goes forwards
M569 P21.0 S1 D2                           	; physical drive 21.0 goes forwards

M915 P0.0:0.1:0.2:0.3:0.4:0.5 T1 ; disable coolstep
M915 P20.0:21.0 T1 ; disable coolstep

Drivers reports

Drive 0 runs in reverse, active low enable, timing fast, mode stealthChop, ccr 0x08053, toff 3, tblank 1, thigh 200 (46.9 mm/sec), tpwmthrs 200 (46.9 mm/sec), pwmScaleSum 24, pwmScaleAuto 2, pwmOfsAuto 32, pwmGradAuto 3, pos 824
Driver 0.0: stall threshold 1, filter off, steps/sec 200 (40.0 mm/sec), coolstep threshold 1 (9376.9 mm/sec), action on stall: none
Drive 1 runs in reverse, active low enable, timing fast, mode stealthChop, ccr 0x08053, toff 3, tblank 1, thigh 200 (46.9 mm/sec), tpwmthrs 200 (46.9 mm/sec), pwmScaleSum 22, pwmScaleAuto 0, pwmOfsAuto 32, pwmGradAuto 1, pos 168
Driver 0.1: stall threshold 1, filter off, steps/sec 200 (40.0 mm/sec), coolstep threshold 1 (9380.6 mm/sec), action on stall: none
Drive 2 runs in reverse, active low enable, timing fast, mode stealthChop, ccr 0x08053, toff 3, tblank 1, thigh 200 (46.8 mm/sec), tpwmthrs 200 (46.8 mm/sec), pwmScaleSum 19, pwmScaleAuto 0, pwmOfsAuto 29, pwmGradAuto 14, pos 24
Driver 0.2: stall threshold 1, filter off, steps/sec 200 (39.9 mm/sec), coolstep threshold 1 (9356.3 mm/sec), action on stall: none
Drive 3 runs forwards, active low enable, timing fast, mode stealthChop, ccr 0x08053, toff 3, tblank 1, thigh 50 (37.8 mm/sec), tpwmthrs 50 (37.8 mm/sec), pwmScaleSum 23, pwmScaleAuto 0, pwmOfsAuto 34, pwmGradAuto 23, pos 648
Driver 0.3: stall threshold 1, filter off, steps/sec 200 (8.1 mm/sec), coolstep threshold 1 (1890.0 mm/sec), action on stall: none
Drive 4 runs forwards, active low enable, timing fast, mode stealthChop, ccr 0x08053, toff 3, tblank 1, thigh 50 (37.8 mm/sec), tpwmthrs 50 (37.8 mm/sec), pwmScaleSum 24, pwmScaleAuto 0, pwmOfsAuto 35, pwmGradAuto 20, pos 648
Driver 0.4: stall threshold 1, filter off, steps/sec 200 (8.1 mm/sec), coolstep threshold 1 (1890.0 mm/sec), action on stall: none

Speeds

M566 X700  U700  Y600   Z60:60     E300:300                  		; set maximum instantaneous speed changes (mm/min)
M203 X6000 U6000 Y6000  Z1800:1800 E3600:3600            			; set maximum speeds (mm/min)
M201 X800  U800  Y900   Z100:100   E600:600               			; set accelerations (mm/s^2)
M204 P800 T1600

Currents and steps

M906 X2125 U2125 Y2000 Z1600:1600 E350:350 I50 
M84 X0 U3 Y1 S30                               
M350 X16 U16 Y16 Z16:16 E16:16 I1
M92 X79.9840 U79.9520 Y80.1603 Z396.8254 E699.3007:699.3007