Posts made by waddo10

@mgjosh A7X is the new one i had bought. 9CR is the one ive been using for a long time and suspected was going faulty. 9CR is the only one that works with my current config. That you for your reply.

@phaedrux Well spotted. I have downloaded again and appears to have worked this time.
I am still testing at the moment, not quite sure whats going on. Using a old model i had printed which i know loads the heightmap.
Just loading the standard heightmap that mesh compensation generates.

@droftarts Do you think the old or the new one is the clone? As in ive been using a clone all along?

Tested the old and new bltouch with the updated firmware and config adjustment. Old BLTouch homes fine. New BLTouch is the same as before, Pin doesn't deploy when trying to home Z.
On the old bltouch on startup the pin probes in and out, ends with the pin stowed and output reads 0. M401 pin out Output 0, M402 pin stowed output 0. M401 and touch the pin output 1000.
On the new bltouch on startup the pin probes in and out, ends with the pin stowed and output reads 1000. M401 pin out Output 1000, M402 pin stowed output 1000. M401 and touch the pin output 0.

Strange behavior.

@droftarts
Updated and this is my M122

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3beta3 (2021-04-22 16:27:28) running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L4MSJ-6J1F6-3SJ6L-991UR
Used output buffers: 3 of 24 (18 max)
=== RTOS ===
Static ram: 23156
Dynamic ram: 75272 of which 12 recycled
Never used RAM 15976, free system stack 180 words
Tasks: NETWORK(ready,14.9%,143) HEAT(delaying,0.0%,306) Move(notifyWait,0.1%,190) MAIN(running,84.5%,441) IDLE(ready,0.5%,19), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:06:53 ago, cause: power up
Last software reset at 2021-05-14 14:06, reason: User, GCodes spinning, available RAM 15800, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x10
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 27.8, current 31.3, max 31.6
Supply voltage: min 24.2, current 24.3, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-05-14 15:13:09
Cache data hit count 4294967295
Slowest loop: 863.58ms; fastest: 0.15ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.6ms, write time 205.5ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 1469.12ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address cc:50:e3:e3:b9:19
WiFi Vcc 3.35, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25360
WiFi IP address 192.168.1.208
WiFi signal strength -47dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

I have modified that line of GCode and will test it now.

Just been comparing the two BLTouche's side by side and noticed a bit of a difference on the circuit board between the two even though they are both V3.1

New

Old

So before updating i never had any problems with my BLTouch/bed leveling. I have a 410x410 bed with a flex plate and its not perfectly flat so always used mesh bed leveling. Everything printed pretty much spot on. I updated to 3.3.0 and carry out a new bed probe for a new height map as the old one disappeared during the upgrade. First print was a success but after powering down and back on the following day it appeared to be not loading the height map and putting down a poor first layer. Mesh leveled again and same result. Thought that maybe the BLtouch was on the way out so bought a new one but the new one doesn't deploy when homing the Z. Pin moved fine using M401 and M402. Plugged the old one back in and it homes fine. So im thinking either the new one is a fake/faulty or i could possible have something in my GCode that it doesnt want to play with.
Can anyone offer any insight before i send it back?
This is my Gcode, like i said it works with the old probe but not the new yet im still getting poor bed leveling results.

config.g

; General preferences
G90                                                       ; send absolute coordinates...
M83                                                       ; ...but relative extruder moves
M550 P"Ender 3"                                           ; set printer name

; Network
M551 P"PASSWORD"                                       ; set password
M552 S1                                                   ; enable network
M586 P0 S1                                                ; enable HTTP
M586 P1 S0                                                ; disable FTP
M586 P2 S0                                                ; disable Telnet

; Drives
M569 P0 S1                                                ; physical drive 0 goes forwards
M569 P1 S1                                                ; physical drive 1 goes backwards
M569 P2 S0                                                ; physical drive 2 goes forwards
M569 P3 S1                                                ; physical drive 3 goes forwards
M569 P4 S0                                                ; physical drive 4 goes forwards
M584 X0 Y1 Z2:4 E3                                        ; set drive mapping
M671 X-20:400 Y200:200 S2.0                               ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
M350 X16 Y16 Z16 E16 I1                                   ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z400.00 E403.19                        ; set steps per mm
M566 X300.00 Y300.00 Z60.00 E120.00                       ; set maximum instantaneous speed changes (mm/min), Jerk
M203 X9000.00 Y9000.00 Z600.00 E1400.00                   ; set maximum speeds (mm/min)
M201 X600.00 Y600.00 Z120.00 E250.00                      ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z800 E800                                 ; set motor currents (mA)
M84 S0                                                    ; Disable motor idle current reduction

; Axis Limits
M208 X-5:400 Y0:400                                       ; set axis minima
M208 X400 Y400 Z500 S0                                    ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                                       ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                                       ; configure active-high endstop for low end on Y via pin ystop

; Z-Probe
M950 S0 C"exp.heater3"                                    ; create servo pin 0 for BLTouch
M558 P9 C"zprobe.in+zprobe.mod" H5 F180 T6000 A30 S0.02  ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-35 Y0 Z1.86                                    ; set Z probe trigger value, offset and trigger height
M557 X10:360 Y10:360 S175                                 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T98801 B4185             ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                                     ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S0.80                                          ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                   ; map heated bed to heater 0
M143 H0 S150                                              ; set temperature limit for heater 0 to 80C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8    ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                                      ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                          ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"fan0" Q500                                      ; create fan 0 on pin fan0 and set its frequency
;M106 P0 C"Part Cooling" S1.0 H1 T45                         ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"fan1" Q100                                      ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"Hot end" S1.0 H1 T30                              ; set fan 1 name and value. Thermostatic control is turned on

; Tools
M563 P0 S"Hot End" D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                           ; set tool 0 axis offsets
G10 P0 R0 S0                                              ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                                         ; enable support for PanelDue
M501                                                      ; load saved parameters from non-volatile memory
M911 S21 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"        ; set voltage thresholds and actions to run on power loss
T0                                                        ; select first tool

deployprobe.g

M280 P0 S10 ; deploy BLTouch

Homeall.g

;G91                     ; relative positioning
;G1 H2 Z5 F18000         ; lift Z relative to current position
G1 H2 Z5 F6000         ; lift Z relative to current position
G1 H1 X-235 Y-235 F2500 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-235 Y-235 F360  ; move slowly to X and Y axis endstops once more (second pass)
G90                     ; absolute positioning
;G1 X200 Y200 F18000     ; go to first probe point
G1 X200 Y200 F6000     ; go to first probe point
G30                     ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 Z5 F100             ; lift Z relative to current position
;G90                    ; absolute positioning

homez.g

; homez.g
; called to home the Z axis
G91                 ; relative positioning
G1 H2 Z5 F18000     ; lift Z relative to current position
G90                 ; absolute positioning
G1 X200 Y200 F18000 ; go to first probe point
G30                 ; home Z by probing the bed

@Veti Thank you so much for the help. I was starting to regret buying the duet. All i needed was some patience and some guidance. Thank you

@Veti Sorry, i meant X axis. Its printing off centre.

Brilliant problem solved. On to my next one, the print is about 15mm to the right on the Z axis. Google seems to have alot more information on this one ha.

I've reached the end of google for an answer so I'm asking here. I've got my Duet 2 wifi wired and setup. Everything seems good apart from one problem. If I home the axis individually they all home fine. If I home all together then the Z axis (bltouch) trys to home off the bed. The same happens at the start of a print. I imagine I've missed something out of the config. Any help would be much appreciated.