Posts made by Vladimir

Good afternoon. Is it clear enough that I set out my question?

When starting auto bed leveling from DWC, the probe (NPN output normally-open inductive or capacitive sensor) checks the bed tilt at two points, but does not automatically align it. If I understood correctly, then the engines should do this automatically, but they are silent ... (. P.S. table I intentionally set crookedly with a height difference of 0.5-1cm.

Good afternoon.
I can 't deal with the bed automatic leveling. The probe operates, but the motors do not align the bed. What am I doing wrong?
In advance, thank you for your answerhomeall.g config.g bed.g

absolutely I am in a stupor
Gives error during diagnostics M122
G29 no valid grid defined for probe

config - fragment
; Axis Limits
M208 X300 Y200 Z0 S1 ; set axis minima
M208 X750 Y450 Z500 S0 ; set axis maxima

; Endstops
M574 X0 S0 "X-stop"
M574 Y0 S0 "Y-stop"
; M574 Z0 S0 "Z-stop"

; Z-Probe

M574 X1 Y2 S0
; M558 P5 I1 H5 F120 T6000
M558 P8 I1 R0.5 H5 T240 F250 A0 S0.04
G31 X0 Y0 Z0,1
M557 X30:740 Y0:450 S20 ; define mesh grid

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3S4-6J9F0-3S86Q-1ARVF
Used output buffers: 3 of 24 (13 max)
=== RTOS ===
Static ram: 30516
Dynamic ram: 92312 of which 32 recycled
Exception stack ram used: 504
Never used ram: 7708
Tasks: NETWORK(ready,640) HEAT(blocked,1240) DUEX(suspended,160) MAIN(running,3668) IDLE(ready,156)
Owned mutexes:
=== Platform ===
Last reset 01:56:42 ago, cause: software
Last software reset at 2020-02-26 10:46, reason: User, spinning module GCodes, available RAM 7740 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 38.5, current 39.8, max 40.3
Supply voltage: min 24.0, current 24.3, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 118/451
Driver 1: standstill, SG min/max 122/436
Driver 2: standstill, SG min/max 107/415
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max 217/528
Driver 6: standstill, SG min/max 237/478
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-02-26 12:43:31
Cache data hit count 4294967295
Slowest loop: 3.20ms; fastest: 0.09ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 167, MaxWait: 4975468ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 14, completed moves: 14, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.57ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running

Maybe I 'm in the wrong thread having a discussion and it needs to be moved to "Firmware Installation" if yes moderator tell how to do it thank you

0

So far,the movements of top portal and z limited by mm and only one end stop
But adjustment of sensor and compensator I do not understand yet.

you are right I send M115 - the reply: RRF for Duet Wi Fi/ Ethernet Firmvare_version:3.0 Electronics: Duet WiFi 1.02 or later + duex5 firmware_date:2020-01-03b3

Good afternoon
Please help with the Сonfig file for Duet Wi Fi version 2.03. generated by RepRapFirmware Con.Tool v2.1.6
I assembled a Cartesian printer where XY moves in the same plane with ball screws and 3 step motors
the Z table is lowered with balls crews and 2 step motors. I connect inductive sensor NPN normally open. The problem is that I can’t level table with Z ptobe and I can’t get a mesh bed compensation.
Please help me what am I doing wrong
kind regards
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.6 on Tue Jan 14 2020 10:57:13 GMT+0300 (Москва, стандартное время)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Gnutik" ; set printer name
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
;***************************************
; M564 S0 H0
;***************************************
; Drives
M569 P3 S1 ; physical drive 3 goes forwards Extruder
M569 P0 S0 ; physical drive 0 goes forwards drive Y
M569 P1 S0 ; physical drive 1 goes forwards drive Y
M569 P2 S0 ; physical drive 2 goes forwards drive X
M569 P5 S0 ; physical drive 5 goes forwards drive Z
M569 P6 S0 ; physical drive 6 goes forwards drive Z
M584 X2 Y0:1 Z5:6 E3
;***********************
M671 X-27:980 Y21:21
;***********************
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X400.00 Y400.00 Z1280.00 E418.50 ; set steps per mm
M566 X400.00 Y400.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min)
M201 X400.00 Y400.00 Z10.00 E250.00 ; set accelerations (mm/s^2)
M906 X1800 Y1800 Z1800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X300 Y200 Z0 S1 ; set axis minima
M208 X750 Y450 Z500 S0 ; set axis maxima
; Endstops
M574 X0 S0 "X-stop"
M574 Y0 S0 "Y-stop"
M574 Z0 S0 "Z-stop"
; Z-Probe
M558 P5 I1 H5 F120 T6000
G31 X0 Y0 Z0,1
M557 X30:740 Y0:450 S20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
M501

Good afternoon

Please help with the Сonfig file for Duet Wi Fi version 2.03
I assembled a Cartesian printer where XY moves in the same plane with ball screws and 3 step motors
the Z table is lowered with balls crews and 2 step motors. I connect inductive sensor NPN normally open;( works at a height of about 2 mm from the Al table in my opinion the sensor response level is low to a heated table)
The problem is that I can’t level Z table with a probe and I can’t get a table map and auto-calibration

Please help me what am I doing wrong

kind regards

; Configuration file for Duet WiFi (firmware version 2.03)

; executed by the firmware on start-up

;

; generated by RepRapFirmware Configuration Tool v2.1.6 on Tue Jan 14 2020 10:57:13 GMT+0300 (Москва, стандартное время)

; General preferences

G90 ; send absolute coordinates...

M83 ; ...but relative extruder moves

M550 P"Gnutik" ; set printer name

; Network

M552 S1 ; enable network

M586 P0 S1 ; enable HTTP

M586 P1 S0 ; disable FTP

M586 P2 S0 ; disable Telnet

;***************************************

; M564 S0 H0

;***************************************

; Drives

M569 P3 S1 ; physical drive 3 goes forwards Extruder

M569 P0 S0 ; physical drive 0 goes forwards drive Y

M569 P1 S0 ; physical drive 1 goes forwards drive Y

M569 P2 S0 ; physical drive 2 goes forwards drive X

M569 P5 S0 ; physical drive 5 goes forwards drive Z

M569 P6 S0 ; physical drive 6 goes forwards drive Z

M584 X2 Y0:1 Z5:6 E3

;***********************

M671 X-27:980 Y21:21

;***********************

M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation

M92 X400.00 Y400.00 Z1280.00 E418.50 ; set steps per mm

M566 X400.00 Y400.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)

M203 X6000.00 Y6000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min)

M201 X400.00 Y400.00 Z10.00 E250.00 ; set accelerations (mm/s^2)

M906 X1800 Y1800 Z1800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent

M84 S30 ; Set idle timeout

; Axis Limits

M208 X300 Y200 Z0 S1 ; set axis minima

M208 X750 Y450 Z500 S0 ; set axis maxima

; Endstops

M574 X0 S0 "X-stop"

M574 Y0 S0 "Y-stop"

M574 Z0 S0 "Z-stop"

; Z-Probe

M558 P5 I1 H5 F120 T6000

G31 X0 Y0 Z0,1

M557 X30:740 Y0:450 S20 ; define mesh grid

; Heaters

M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp

M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0

M143 H0 S120 ; set temperature limit for heater 0 to 120C

M307 H0 B0 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit

M140 H0 ; map heated bed to heater 0

M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp

M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1

M143 H1 S280 ; set temperature limit for heater 1 to 280C

M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

; Fans

M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off

M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools

M563 P0 D0 H1 F0 ; define tool 0

G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets

G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

M501

Now I made the record right? is it new thread for my post

I'm not an engineer but
I became interested in assembling a 3D printer and there were questions on which I have not yet decided. Can I ask you in this forum what is wrong I am writing in the config.g so that the Z sensor starts working