thankyou.
i got FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03beta3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-03-25b6
so 2.05.1, then 3.0 & then 3.1.1
A pitty i couldn't upgrade direct to 3.1.1
thankyou.
i got FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03beta3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-03-25b6
so 2.05.1, then 3.0 & then 3.1.1
A pitty i couldn't upgrade direct to 3.1.1
Hi,
if your using Duet Wifi v1.04, which firmware package do i use?
Duet2and3Firmware-3.1.1.zip
OR
Duet2CombinedFirmware.bin
regards,
Tony.
ok so i go to Step 8.
Sent M552 S0
then M552 S1 P192.168.1.120
and now i get this... and even after 30seconds, i try M552 & it remains with those errors
no errors in the browser when going the direct IP address.
and strangely, it knows my assigned static IP address but it cannot remember it? maybe this is a firmware issue?
I didn't have to send the M587 S & P command, it knows my static address, but when we run the M587, the SSID is remembered, but the IP is NULLED, yet the static IP address is there.
should i force the static IP in the config.h file?
@dc42 said in Newbie Seeking Help:
M115
Ok the firmware update worked perfectly, however, this problem remains!
; Configuration file for Duet WiFi (firmware version 2.00)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri May 01 2020 01:28:58 GMT+1000 (Australian Eastern Standard Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name
M667 S1 ; select CoreXY mode
; Network
M552 S1 ; enable network
;M552 P192.168.1.120
;M554 P192.168.1.255
;M553 P225.255.255.0
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E98.00 ; set steps per mm
M566 X600.00 Y600.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z180.00 E1500.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E10000.00 ; set accelerations (mm/s^2)
M906 X950 Y950 Z950 E950 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X330 Y330 Z400 S0 ; set axis maxima
; Endstops
M574 X1 Y1 Z1 S0 ; set active low and disabled endstops
; Z-Probe
M558 P5 H5 F0 T6000 ; set Z probe type to switch and the dive height + speeds
G31 P600 X0 Y0 Z0 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid
; Heaters
M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
Thankyou. I have deleted those other files. Checked /sys folder again.
But still no DWC !!!!
This is interesting. Does this mean i can't see my /sys files?
If so why?
It does remember my SSID, just not my IP address.
Do i need to port forward? i have an Asus GT-AC5300 router.
So i have /www separate & /sys separate.
The /config/sys & /config/www directory & files, i was just trying to see if that would solve the problem.
Hi
Im trying to get my Duet 2 v2.0 running. I can connect via YAT USB COM8 port. I've tried sending my wifi details & the M587 command seems to accept but when i request register, it comes back with IP NULL.
I have my IP set for 192.168.1.120 & it receive "Your Duet rejected the HTTP request: page not found".
Blue light is ON solid. i.e. not flashing. The band i am connecting the Duet 2 is 2G.
I did a DuetWiFiServer.bin update but same problem exists.
I have been trying for days to get the http working & updating the firmware to V3.01 RC1 without success.
i also have a microsd car with /www & /sys folder in the root section.
What can i do now?
Thanks,
Tony.