Posts made by tape

Yes exactly the same.

i have the latest firmware as You can see
M122
=== Diagnostics ===
Used output buffers: 3 of 32 (9 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19beta10+2 running on Duet WiFi 1.0
Board ID: 08DDM-9FAM2-LW4S8-6JTDD-3S46J-93ZHW
Static ram used: 20912
Dynamic ram used: 94544
Recycled dynamic ram: 3328
Stack ram used: 1304 current, 4824 maximum
Never used ram: 7464
Last reset 00:08:30 ago, cause: power up
Last software reset reason: User, spinning module GCodes, available RAM 3240 bytes (slot 0)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min -250.7, current 35.6, max 36.2
Supply voltage: min 12.0, current 12.0, max 12.2, under voltage events: 0, over voltage events: 0
Driver 0: stalled standstill
Driver 1: stalled standstill
Driver 2: stalled standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 2017-07-20 18:21:02
Slowest main loop (seconds): 0.007690; fastest: 0.000030
=== Move ===
MaxReps: 2, StepErrors: 0, FreeDm: 240, MinFreeDm 236, MaxWait: 3682ms, Underruns: 0, 0
Scheduled moves: 8, completed moves: 8
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
Probe change coordinates:
=== Heat ===
Bed heater = 0, chamber heater = -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
WiFi firmware version 1.19beta9
WiFi MAC address 5c:cf:7f:ef:3f:a8
WiFi Vcc 3.07, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 32464
WiFi IP address 192.168.1.90
WiFi signal strength -35dBm
HTTP sessions: 1 of 8
Socket states: 2 2 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0)

i have the port 80 open and forward to the ip 192.168.1.90 but i cant connect from the outside, only inside the network.
but if i connect inside the network via wifi and then disconnect wifi (still connected by 4G), i'm still able to control the duet.
i have an arduino Yun and i can control it from the outside with no problems at all!!!

best regards

i'm having the same issue here and i need to solve it too!!!

best regards

problem solved. thanks again

thanks

M906 X800 Y800 Z800 E1000 ; Set motor currents (mA)
M201 X800 Y800 Z15 E400 ; Accelerations (mm/s^2)
M203 X15000 Y15000 Z240 E100 ; Maximum speeds (mm/min)
M566 X600 Y600 Z30 E20 ; Minimum speeds mm/minute
M208 X200 Y175 Z180 ; set axis maxima (adjust to suit your machine)
M208 X0 Y0 Z-0.2 S1 ; set axis minimum (adjust to make X=0 and Y=0 the edge of the bed)
M92 X80 Y80 Z4000 ; Set axis steps/mm
M92 E100:100

https://drive.google.com/file/d/0Bx0mLwkx-u8vdDctbEdvRUhvRTQ/view?usp=sharing

ok just tested with a gcode with no retraction and it works fine.

how can i fix the retraction?

only that wifi module connected

no errors

it does not retract

can someone please help me with this?

My prusa i3 with duet wifi 1.19beta firmware stops for a second and resumes printing when it should be a continuous print,

video to see what is happening.

https://www.youtube.com/watch?v=acXxiNrkUeg

thanks in advance.

best regards

hello after firmware update for 1.19beta the wifi module stoped responding,
Upload successful
WiFi module started
Error: Failed to initialise WiFi module, code -10
[ERROR] Error: Failed to initialise WiFi module, code -10

what can i do to fix this?
thanks in advance